[PATCH v10 0/3] Add support for the S6E3HA2 panel on TM2 board

[Hoegeun Kwon]

Hi all,


This patchset is resent patchset.

Because I have a missing TO, CC, I sent it again.

Sorry, I will send it in the correct format next time.


Best Regards,

Hoegeun


On 02/22/2017 10:09 AM, Hoegeun Kwon wrote:
> Dear Thierry,
>
> I understand that your opinion is:
> It is better to handle the error every time it is input to the
> register, rather than error handling at once in the struct using
> error. This not only makes the code easier to maintain, but also
> reduces unnecessary computation.
>
> So I modified the panel driver to code-by-code error handling.
> If this is not your opinion, could you tell me what your opinion?
>
> Best Regards,
> Hoegeun
>
>
> Changes for V10:
> - Fixed code-by-code error handling.
>
> Changes for V9:
> - Fixed the te-gpio to optional in bindings
>
> Changes for V8:
> - Applied below two patches: (drm/exynos)
>   : drm/exynos: mic: Add mode_set callback function
>   : drm/exynos: mic: Fix parse_dt function
> - The dt-binding patch and driver patch were divided.
> - Rebase these patches on samsung SoC tree[1] and tm2 touckey patch[2].
>
> Change for V7:
> - Fixed the mode_set callback function of mic device driver.
>   because the mic register is initialized when entering suspend
>   mode, so should set the reg value whenever pre_enable is
>   called.
>
> Changes for V6:
> - Fixed the parse_dt function of dsi device driver.
> - Removed OF graph of panel in DT and DT binding document.
> - Fixed the s6e3ha2 panel device driver.
>   - Fixed from number size to ARRAY_SIZE().
>   - Fixed error handling in mipi_dsi_dcs_* functions.
>   - Fixed the clock of display_mode.
>   - Removed unnecessary casting and error log.
>
> Change for V5:
> - The V5 has only one fix in V4 below.
> - Removed the enable check of the mic driver in mode_set
>   callback, because mode_set should be performed every time.
>
> Changes for V4:
> - Removed display-timings in devicetree, the display-timings has
>   been fixed to be provided by the device driver.
> - Added the mode_set callback function into exynos_drm_mic,
>   because the exynos_drm_mic driver can not parse a videomode
>   struct by removing the display-timings from the devicetree.
>
> Changes for V3:
> - In the DT binding document, made it clearly that the panel is a
>   child node of dsi.
> - Fix reset-gpio active from high to low.
> - Is the OF graph saying related to patch2?
>   Althogh the panel is a child of dsi, I think OF graph necessary.
>   because if a remote-endpoint is not specified, the dsi also
>   panel is not probed.
> - The display-timings has been fixed to be provided by the device
>   driver. however, I think display-timings is necessary in dts.
>   because if dts does not have display-timings, dsi will not load.
>
> Changes for V2:
> - Fixed the samsung,s6e3ha2.txt DT document.
>   - Added active high or low after the description of the GPIOs.
>   - Removed the reg and added a description of the virtual
>     channel number of a DSI peripheral.
>
> Depends on:
> [1] https://git.kernel.org/cgit/linux/kernel/git/krzk/linux.git/ 
> (for-next branch)
> [2] https://patchwork.kernel.org/patch/9504131/
>     - ("arm64: dts: exynos: Add tm2 touchkey node")
>
> Hoegeun Kwon (2):
>   dt-bindings: Add support for samsung s6e3ha2 panel binding
>   drm/panel: Add support for S6E3HA2 panel driver on TM2 board
>
> Hyungwon Hwang (1):
>   arm64: dts: exynos: Add support for S6E3HA2 panel device on TM2 board
>
>  .../bindings/display/panel/samsung,s6e3ha2.txt     |  28 +
>  arch/arm64/boot/dts/exynos/exynos5433-tm2.dts      |  12 +
>  drivers/gpu/drm/panel/Kconfig                      |   6 +
>  drivers/gpu/drm/panel/Makefile                     |   1 +
>  drivers/gpu/drm/panel/panel-samsung-s6e3ha2.c      | 739 
> +++++++++++++++++++++
>  5 files changed, 786 insertions(+)
>  create mode 100644 
> Documentation/devicetree/bindings/display/panel/samsung,s6e3ha2.txt
>  create mode 100644 drivers/gpu/drm/panel/panel-samsung-s6e3ha2.c
>