[RFC v2 6/7] IIO: add bindings for stm32 DFSDM filter

[Jonathan Cameron]

On 13/02/17 16:38, Arnaud Pouliquen wrote:
> Add bindings that describe Digital Filter for Sigma Delta
> Modulators. DFSDM allows to connect sigma delta
> modulators and/or PDM microphones.
> 
> Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen at st.com>
> ---
>  .../bindings/iio/adc/st,stm32-dfsdm-adc.txt        | 125 +++++++++++++++++++++
>  1 file changed, 125 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/iio/adc/st,stm32-dfsdm-adc.txt
> 
> diff --git a/Documentation/devicetree/bindings/iio/adc/st,stm32-dfsdm-adc.txt b/Documentation/devicetree/bindings/iio/adc/st,stm32-dfsdm-adc.txt
> new file mode 100644
> index 0000000..83937cb
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/iio/adc/st,stm32-dfsdm-adc.txt
> @@ -0,0 +1,125 @@
> +STMicroelectronics STM32 DFSDM ADC device driver
> +
> +
> +STM32 DFSDM ADC is a sigma delta analog-to-digital converter dedicted to
> +interface external sigma delta modulators to stm32 micro controlers.
> +it is mainly targeted for:
> +- Sigma delta modulators ( motor control, metering...)
> +- PDM microphones ( audio digital microphone)
> +
> +It featured with up to 8 serial digital interface (SPI or Manchester) and
> +up to 4 filters.
> +
> +Each instance of the sub-drivers uses one filter instance.
> +
> +Contents of a stm32 dfsdmc root node:
> +-------------------------------------
> +Required properties:
> +- compatible: Should be "st,stm32-dfsdm-adc".
> +- reg: Offset and length of the DFSDM block register set.
> +- clocks: IP and serial interfaces clocking. Should be set according
> +		to rcc clock ID and "clock-names".
> +- clock-names: Input clock name "dfsdm" must be defined,
> +		"audio" is optional. If defined CLKOUT is based on the audio
> +		clock, else "dfsdm" is used.
> +- clocks: Clock for the analog circuitry (common to all ADCs).
> +- clock-names: Must be "adc".
> +
> +Optional properties:
> +- st,clkout-freq: needed for SPI master mode
> +		  SPI clock OUT frequency (Hz).This clock must be set according
> +		  to "clock" property. Frequency must be a multiple of the rcc
> +		  clock frequency. If not, clkout frequency will not be
> +		  accurate.
> +
> +Contents of a stm32 DFSDM child nodes:
> +----------------------------------------
> +
> +Required properties:
> +- compatible: Must be:
> +	"st,stm32-dfsdm-adc" for sigma delta ADCs
> +	"st,stm32-dfsdm-pdm" for audio digital microphone.
> +- reg: Specifies the DFSDM filter instance.
> +- interrupts: IRQ lines connected to each DFSDM filter instance.
> +- st,adc-channels:	List of single-ended channels muxed for this ADC.
> +- st,adc-channel-names:	List of single-ended channels Name.
> +- st,dai-filter-order:  SinC filter order from 0 to 5.
> +			0: FastSinC
> +			[1-5]: order 1 to 5.
> +			For audio purpose it is recommended to use order 3 to 5.
> +
> +Required properties for "st,stm32-dfsdm-adc" compatibility:
> +- #io-channel-cells = <1>: See the IIO bindings section "IIO consumers".
> +- io-channels: from common iio binding. use to pipe external sigma delta
> +		modulator or internal ADC output to dfsdm channel.
> +
> +Required properties for "st,stm32-dfsdm-pdm" compatibility:
> +- #sound-dai-cells: must be set to 0.
> +- dma: DMA controller phandle and DMA request line associated to the
> +		filter instance ( specified by the field "reg")
> +- dma-names: must be "rx"
> +
> +Optional properties:
> +- st,adc-channel-types:	Single-ended channel input type. Default value is 0.
> +			- "SPI_R": SPI with data on rising edge (default)
> +			- "SPI_F": SPI with data on falling edge
> +			- "MANCH_R": manchester codec, rising edge = logic 0
> +			- "MANCH_F": manchester codec, falling edge = logic 1
> +- st,adc-channel-clk-src: Conversion clock source. default value is 1.
> +			  - "CLKIN": External SPI clock (CLKIN x)
> +			  - "CLKOUT": internal SPI clock (CLKOUT) (default)
> +			  - "CLKOUT_F": internal SPI clock divided by 2 (falling edge).
> +			  - "CLKOUT_R": internal SPI clock divided by 2 (rising edge).
> +
> +- st,adc-alt-channel: Must be defined if Two sigma delta modulator are
> +			  connected on same SPI input.
> +			  If not set channel n is connected to SPI input n.
> +			  If set channel n is connected to SPI input n + 1.
> +
> +- st,filter0-sync: Set to 1 to synchronize with DFSDM filter instance 0.
> +		   to used for multi microphone synchronization.
> +
> +Example of a sigma delta adc purpose:
> +	ads1202: simple_sd_adc at 0 {
> +		compatible = "sd-modulator";
This suggests to me that we ought to have a primary compatible of the actual part
number.  Down the line I suspect we will want to distinguish between the different
ADCs and it's kind of easier if we do it from the start.  May not be obvious
later which the 'default sd-modulator' is.
> +		#io-channel-cells = <1>;
> +		status = "okay";
> +	};
> +	dfsdm: dfsdm at 40017000 {
> +		compatible = "st,stm32h7-dfsdm";
> +		reg = <0x40017000 0x400>;
> +		clocks = <&timer_clk>;
> +		clock-names = "dfsdm";
> +
> +		dfsdm_adc0: dfsdm-adc0 at 0 {
> +			compatible = "st,stm32-dfsdm-adc";
> +			#io-channel-cells = <1>;
> +			reg = <0>;
> +			interrupts = <110>;
> +			st,adc-channels = <0>;
> +			st,adc-channel-names = "in0";
> +			st,adc-channel-types = "SPI_R";
> +			st,adc-channel-clk-src = "CLKOUT";
> +			io-channels = <&ads1202 0>;
> +	};
> +
> +Example of a pdm microphone purpose:
Is there nothing about the particular pdm microphone that is
worth giving it an explicit representation in the device
tree?  I've no idea having never used one!
> +	dfsdm: dfsdm at 40017000 {
> +		compatible = "st,stm32h7-dfsdm";
> +		reg = <0x40017000 0x400>;
> +		clocks = <&timer_clk>;
> +		clock-names = "dfsdm";
> +
> +		dfsdm_pdm0: dfsdm-pdm at 0 {
> +			compatible = "st,stm32-dfsdm-pdm";
> +			#sound-dai-cells = <0>;
> +			reg = <0>;
> +			interrupts = <110>;
> +			dmas = <&dmamux1 102 0x400 0x00>;
> +			dma-names = "rx";
> +			st,adc-channels = <0>;
> +			st,adc-channel-names = "pdm1";
> +			st,adc-channel-types = "SPI_R";
> +			st,adc-channel-clk-src = "CLKOUT";
> +		};
> +	}
>