[PATCH v2 20/22] Documentation: PCI: Add userguide for PCI endpoint test function

Kishon Vijay Abraham I kishon at ti.com
Fri Feb 17 01:50:40 PST 2017


Add documentation to help users use pci-epf-test function driver
and pci_endpoint_test host driver for testing PCI.

Signed-off-by: Kishon Vijay Abraham I <kishon at ti.com>
---
 Documentation/PCI/endpoint/pci-test-howto.txt |  167 +++++++++++++++++++++++++
 1 file changed, 167 insertions(+)
 create mode 100644 Documentation/PCI/endpoint/pci-test-howto.txt

diff --git a/Documentation/PCI/endpoint/pci-test-howto.txt b/Documentation/PCI/endpoint/pci-test-howto.txt
new file mode 100644
index 0000000..4141b2b
--- /dev/null
+++ b/Documentation/PCI/endpoint/pci-test-howto.txt
@@ -0,0 +1,167 @@
+			    PCI TEST USERGUIDE
+		    Kishon Vijay Abraham I <kishon at ti.com>
+
+This document is a guide to help users use pci-epf-test function driver
+and pci_endpoint_test host driver for testing PCI. The list of steps to
+be followed in the host side and EP side is given below.
+
+1. Endpoint Device
+
+1.1 Endpoint Controller Devices
+
+To find the list of endpoint controller devices in the system:
+
+	# ls /sys/class/pci_epc/
+	  51000000.pcie_ep
+
+1.2 Endpoint Function Drivers
+
+To find the list of endpoint function drivers in the system:
+
+	# ls /sys/bus/pci-epf/drivers
+	  pci_epf_test
+
+1.3 Creating pci-epf-test Device
+
+PCI endpoint function device can be created using the configfs. To create
+pci-epf-test device, the following commands can be used
+
+	# mount -t configfs none /sys/kernel/config
+	# cd /sys/kernel/config/pci_ep/
+	# mkdir dev
+	# mkdir dev/epf/pci_epf_test.0
+
+The "mkdir dev/epf/pci_epf_test.0" above creates the pci-epf-test function
+device. The name given to the directory preceding '.' should match with the
+name of the driver listed in '/sys/bus/pci-epf/drivers' in order for the
+device to be bound to the driver.
+
+The PCI endpoint framework populates the directory with configurable fields.
+
+	# ls dev/epf/pci_epf_test.0/
+	  baseclass_code	function	revid		vendorid
+	  cache_line_size	interrupt_pin	subclass_code
+	  deviceid		peripheral	subsys_id
+	  epc			progif_code	subsys_vendor_id
+
+The pci endpoint function driver populates these entries with default values
+when the device is bound to the driver. The pci-epf-test driver populates
+vendorid with 0xffff and interrupt_pin with 0x0001
+
+	# cat dev/epf/pci_epf_test.0/vendorid
+	  0xffff
+	# cat dev/epf/pci_epf_test.0/interrupt_pin
+	  0x0001
+
+1.4 Configuring pci-epf-test Device
+
+The user can configure the pci-epf-test device using configfs entry. In order
+to change the vendorid and the number of MSI interrupts used by the function
+device, the following commands can be used.
+
+	# echo 0x104c > dev/epf/pci_epf_test.0/vendorid
+	# echo 0xb500 > dev/epf/pci_epf_test.0/deviceid
+	# echo 16 >  dev/epf/pci_epf_test.0/msi_interrupts
+
+1.5 Binding pci-epf-test Device to EP Controller
+
+In order for the endpoint function device to be useful, it has to be bound to
+a PCI endpoint controller driver. Use the configfs to bind the function
+device to one of the controller driver present in the system.
+
+	# echo "51000000.pcie_ep" > dev/epc
+
+Once the above step is completed, the PCI endpoint is ready to establish a link
+with the host.
+
+2. Endpoint Device
+
+2.1 lspci Output
+
+Note that the devices listed here correspond to the value populated in 1.4 above
+
+	00:00.0 PCI bridge: Texas Instruments Device 8888 (rev 01)
+	01:00.0 Unassigned class [ff00]: Texas Instruments Device b500
+
+2.2 Using Endpoint Test function Device
+
+pcitest.sh added in tools/pci/ can be used to run all the default PCI endpoint
+tests. Before pcitest.sh can be used pcitest.c should be compiled using the
+following commands.
+
+	cd <kernel-dir>
+	make headers_install ARCH=arm
+	arm-linux-gnueabihf-gcc -Iusr/include tools/pci/pcitest.c -o pcitest
+	cp pcitest  <rootfs>/usr/sbin/
+	cp tools/pci/pcitest.sh <rootfs>
+
+2.2.1 pcitest.sh Output
+	# ./pcitest.sh
+	BAR tests
+
+	BAR0:           OKAY
+	BAR1:           OKAY
+	BAR2:           OKAY
+	BAR3:           OKAY
+	BAR4:           NOT OKAY
+	BAR5:           NOT OKAY
+
+	Interrupt tests
+
+	LEGACY IRQ:     NOT OKAY
+	MSI1:           OKAY
+	MSI2:           OKAY
+	MSI3:           OKAY
+	MSI4:           OKAY
+	MSI5:           OKAY
+	MSI6:           OKAY
+	MSI7:           OKAY
+	MSI8:           OKAY
+	MSI9:           OKAY
+	MSI10:          OKAY
+	MSI11:          OKAY
+	MSI12:          OKAY
+	MSI13:          OKAY
+	MSI14:          OKAY
+	MSI15:          OKAY
+	MSI16:          OKAY
+	MSI17:          NOT OKAY
+	MSI18:          NOT OKAY
+	MSI19:          NOT OKAY
+	MSI20:          NOT OKAY
+	MSI21:          NOT OKAY
+	MSI22:          NOT OKAY
+	MSI23:          NOT OKAY
+	MSI24:          NOT OKAY
+	MSI25:          NOT OKAY
+	MSI26:          NOT OKAY
+	MSI27:          NOT OKAY
+	MSI28:          NOT OKAY
+	MSI29:          NOT OKAY
+	MSI30:          NOT OKAY
+	MSI31:          NOT OKAY
+	MSI32:          NOT OKAY
+
+	Read Tests
+
+	READ (      1 bytes):           OKAY
+	READ (   1024 bytes):           OKAY
+	READ (   1025 bytes):           OKAY
+	READ (1024000 bytes):           OKAY
+	READ (1024001 bytes):           OKAY
+
+	Write Tests
+
+	WRITE (      1 bytes):          OKAY
+	WRITE (   1024 bytes):          OKAY
+	WRITE (   1025 bytes):          OKAY
+	WRITE (1024000 bytes):          OKAY
+	WRITE (1024001 bytes):          OKAY
+
+	Copy Tests
+
+	COPY (      1 bytes):           OKAY
+	COPY (   1024 bytes):           OKAY
+	COPY (   1025 bytes):           OKAY
+	COPY (1024000 bytes):           OKAY
+	COPY (1024001 bytes):           OKAY
-- 
1.7.9.5




More information about the linux-arm-kernel mailing list