[PATCH v2, 6/6] dt-bindings: phy-mt65xx-usb: add support for new version phy

Chunfeng Yun chunfeng.yun at mediatek.com
Mon Feb 6 22:30:21 PST 2017


On Fri, 2017-01-27 at 14:07 -0600, Rob Herring wrote:
> On Fri, Jan 20, 2017 at 04:18:41PM +0800, Chunfeng Yun wrote:
> > add a new compatible string for "mt2712", and move reference clock
> > into each port node;
> > 
> > Signed-off-by: Chunfeng Yun <chunfeng.yun at mediatek.com>
> > ---
> >  .../devicetree/bindings/phy/phy-mt65xx-usb.txt     |   91 +++++++++++++++++---
> >  1 file changed, 77 insertions(+), 14 deletions(-)
> > 
> > diff --git a/Documentation/devicetree/bindings/phy/phy-mt65xx-usb.txt b/Documentation/devicetree/bindings/phy/phy-mt65xx-usb.txt
> > index 33a2b1e..1d06604 100644
> > --- a/Documentation/devicetree/bindings/phy/phy-mt65xx-usb.txt
> > +++ b/Documentation/devicetree/bindings/phy/phy-mt65xx-usb.txt
> > @@ -6,21 +6,27 @@ This binding describes a usb3.0 phy for mt65xx platforms of Medaitek SoC.
> >  Required properties (controller (parent) node):
> >   - compatible	: should be one of
> >  		  "mediatek,mt2701-u3phy"
> > +		  "mediatek,mt2712-u3phy"
> >  		  "mediatek,mt8173-u3phy"
> > - - reg		: offset and length of register for phy, exclude port's
> > -		  register.
> > - - clocks	: a list of phandle + clock-specifier pairs, one for each
> > -		  entry in clock-names
> > - - clock-names	: must contain
> > -		  "u3phya_ref": for reference clock of usb3.0 analog phy.
> >  
> >  Required nodes	: a sub-node is required for each port the controller
> >  		  provides. Address range information including the usual
> >  		  'reg' property is used inside these nodes to describe
> >  		  the controller's topology.
> >  
> > +Optional properties (controller (parent) node):
> > + - reg		: offset and length of register shared by multiple ports,
> 
> How is this optional?
I put register shared by ports in parent node, but no shared register
for new phy, so change it as optional.

> 
> > +		  exclude port's private register. It is needed on mt2701
> > +		  and mt8173, but not on mt2712.
> > +
> >  Required properties (port (child) node):
> >  - reg		: address and length of the register set for the port.
> > +- clocks	: a list of phandle + clock-specifier pairs, one for each
> > +		  entry in clock-names
> > +- clock-names	: must contain
> > +		  "ref_clk": 48M reference clock for HighSpeed analog phy; and
> 
> _clk is redundant. Just "ref"
Ok
> 
> > +			26M reference clock for SuperSpeed analog phy, sometimes is
> > +			24M, 25M or 27M, depended on platform.
> >  - #phy-cells	: should be 1 (See second example)
> >  		  cell after port phandle is phy type from:
> >  			- PHY_TYPE_USB2
> > @@ -31,21 +37,31 @@ Example:
> >  u3phy: usb-phy at 11290000 {
> >  	compatible = "mediatek,mt8173-u3phy";
> >  	reg = <0 0x11290000 0 0x800>;
> > -	clocks = <&apmixedsys CLK_APMIXED_REF2USB_TX>;
> > -	clock-names = "u3phya_ref";
> >  	#address-cells = <2>;
> >  	#size-cells = <2>;
> >  	ranges;
> >  	status = "okay";
> >  
> > -	phy_port0: port at 11290800 {
> > -		reg = <0 0x11290800 0 0x800>;
> > +	u2port0: port at 11290800 {
> > +		reg = <0 0x11290800 0 0x100>;
> > +		clocks = <&apmixedsys CLK_APMIXED_REF2USB_TX>;
> > +		clock-names = "ref_clk";
> >  		#phy-cells = <1>;
> >  		status = "okay";
> >  	};
> >  
> > -	phy_port1: port at 11291000 {
> > -		reg = <0 0x11291000 0 0x800>;
> > +	u3port0: port at 11290900 {
> > +		reg = <0 0x11290800 0 0x700>;
> > +		clocks = <&clk26m>;
> > +		clock-names = "ref_clk";
> > +		#phy-cells = <1>;
> > +		status = "okay";
> > +	};
> > +
> > +	u2port1: port at 11291000 {
> > +		reg = <0 0x11291000 0 0x100>;
> > +		clocks = <&apmixedsys CLK_APMIXED_REF2USB_TX>;
> > +		clock-names = "ref_clk";
> >  		#phy-cells = <1>;
> >  		status = "okay";
> >  	};
> > @@ -64,7 +80,54 @@ Example:
> >  
> >  usb30: usb at 11270000 {
> >  	...
> > -	phys = <&phy_port0 PHY_TYPE_USB3>;
> > -	phy-names = "usb3-0";
> > +	phys = <&u2port0 PHY_TYPE_USB2>, <&u3port0 PHY_TYPE_USB3>;
> > +	phy-names = "usb2-0", "usb3-0";
> >  	...
> >  };
> > +
> > +
> > +Layout differences of banks between mt8173/mt2701 and mt2712
> > +-------------------------------------------------------------
> > +mt8173 and mt2701:
> > +port        offset    bank
> > +shared      0x0000    SPLLC
> > +            0x0100    FMREG
> > +u2 port0    0x0800    U2PHY_COM
> > +u3 port0    0x0900    U3PHYD
> > +            0x0a00    U3PHYD_BANK2
> > +            0x0b00    U3PHYA
> > +            0x0c00    U3PHYA_DA
> > +u2 port1    0x1000    U2PHY_COM
> > +u3 port1    0x1100    U3PHYD
> > +            0x1200    U3PHYD_BANK2
> > +            0x1300    U3PHYA
> > +            0x1400    U3PHYA_DA
> > +u2 port2    0x1800    U2PHY_COM
> > +            ...
> > +
> > +mt2712:
> > +port        offset    bank
> > +u2 port0    0x0000    MISC
> > +            0x0100    FMREG
> > +            0x0300    U2PHY_COM
> > +u3 port0    0x0700    SPLLC
> > +            0x0800    CHIP
> > +            0x0900    U3PHYD
> > +            0x0a00    U3PHYD_BANK2
> > +            0x0b00    U3PHYA
> > +            0x0c00    U3PHYA_DA
> > +u2 port1    0x1000    MISC
> > +            0x1100    FMREG
> > +            0x1300    U2PHY_COM
> > +u3 port1    0x1700    SPLLC
> > +            0x1800    CHIP
> > +            0x1900    U3PHYD
> > +            0x1a00    U3PHYD_BANK2
> > +            0x1b00    U3PHYA
> > +            0x1c00    U3PHYA_DA
> > +u2 port2    0x2000    MISC
> > +            ...
> > +
> > +    SPLLC shared by u3 ports and FMREG shared by u2 ports on
> > +mt8173/mt2701 are put back into each port; a new bank MISC for
> > +u2 ports and CHIP for u3 ports are added on mt2712.
> > -- 
> > 1.7.9.5
> > 





More information about the linux-arm-kernel mailing list