[PATCH/RFT] ARM: dts: porter: Enable UHS-I SDR-50 and SDR-104

Simon Horman horms+renesas at verge.net.au
Tue Apr 18 02:33:06 EDT 2017


Add the "1v8" pinctrl state and sd-uhs-sdr50 property to SDHI{0,2}.
And the sd-uhs-sdr104 property to SDHI0.

Signed-off-by: Simon Horman <horms+renesas at verge.net.au>
--
Testing failed:
- SDHI0: mmc0: error -110 whilst initialising SD card
- It is unclear if this is something to do with my hardware/firmware
  environment or software problem.
  + SD card CID: 035344534c33324780aa9c34de010600
Untested:
- SDHI2: Untested due to no card present in remotely accessed board
---
 arch/arm/boot/dts/r8a7791-porter.dts | 23 +++++++++++++++++++++--
 1 file changed, 21 insertions(+), 2 deletions(-)

diff --git a/arch/arm/boot/dts/r8a7791-porter.dts b/arch/arm/boot/dts/r8a7791-porter.dts
index 95da5cb9d37a..a0fb8dca3c86 100644
--- a/arch/arm/boot/dts/r8a7791-porter.dts
+++ b/arch/arm/boot/dts/r8a7791-porter.dts
@@ -160,11 +160,25 @@
 	sdhi0_pins: sd0 {
 		groups = "sdhi0_data4", "sdhi0_ctrl";
 		function = "sdhi0";
+		power-source = <3300>;
+	};
+
+	sdhi0_pins_uhs: sd0_uhs {
+		groups = "sdhi0_data4", "sdhi0_ctrl";
+		function = "sdhi0";
+		power-source = <1800>;
 	};
 
 	sdhi2_pins: sd2 {
 		groups = "sdhi2_data4", "sdhi2_ctrl";
 		function = "sdhi2";
+		power-source = <3300>;
+	};
+
+	sdhi2_pins_uhs: sd2_uhs {
+		groups = "sdhi2_data4", "sdhi2_ctrl";
+		function = "sdhi2";
+		power-source = <1800>;
 	};
 
 	qspi_pins: qspi {
@@ -238,22 +252,27 @@
 
 &sdhi0 {
 	pinctrl-0 = <&sdhi0_pins>;
-	pinctrl-names = "default";
+	pinctrl-1 = <&sdhi0_pins_uhs>;
+	pinctrl-names = "default", "state_uhs";
 
 	vmmc-supply = <&vcc_sdhi0>;
 	vqmmc-supply = <&vccq_sdhi0>;
 	cd-gpios = <&gpio6 6 GPIO_ACTIVE_LOW>;
 	wp-gpios = <&gpio6 7 GPIO_ACTIVE_HIGH>;
+	sd-uhs-sdr50;
+	sd-uhs-sdr104;
 	status = "okay";
 };
 
 &sdhi2 {
 	pinctrl-0 = <&sdhi2_pins>;
-	pinctrl-names = "default";
+	pinctrl-1 = <&sdhi2_pins_uhs>;
+	pinctrl-names = "default", "state_uhs";
 
 	vmmc-supply = <&vcc_sdhi2>;
 	vqmmc-supply = <&vccq_sdhi2>;
 	cd-gpios = <&gpio6 22 GPIO_ACTIVE_LOW>;
+	sd-uhs-sdr50;
 	status = "okay";
 };
 
-- 
2.7.0.rc3.207.g0ac5344




More information about the linux-arm-kernel mailing list