[PATCH] ARM: decompressor: reset ttbcr fields to use TTBR0 on ARMv7
Srinivas Ramana
sramana at codeaurora.org
Tue Sep 13 07:52:23 PDT 2016
On 09/12/2016 11:21 PM, Robin Murphy wrote:
> On 12/09/16 07:57, Srinivas Ramana wrote:
>> If the bootloader uses the long descriptor format and jumps to
>> kernel decompressor code, TTBCR may not be in a right state.
>> Before enabling the MMU, it is required to clear the TTBCR.PD0
>> field to use TTBR0 for translation table walks.
>>
>> The 'commit dbece45894d3a ("ARM: 7501/1: decompressor:
>> reset ttbcr for VMSA ARMv7 cores")' does the reset of TTBCR.N, but
>> doesn't consider all the bits for the size of TTBCR.N.
>>
>> Clear TTBCR.PD0 field and reset all the three bits of TTBCR.N to
>> indicate the use of TTBR0 and the correct base address width.
>>
>> Signed-off-by: Srinivas Ramana <sramana at codeaurora.org>
>> ---
>> arch/arm/boot/compressed/head.S | 2 +-
>> 1 file changed, 1 insertion(+), 1 deletion(-)
>>
>> diff --git a/arch/arm/boot/compressed/head.S b/arch/arm/boot/compressed/head.S
>> index af11c2f8f3b7..fc6d541549a2 100644
>> --- a/arch/arm/boot/compressed/head.S
>> +++ b/arch/arm/boot/compressed/head.S
>> @@ -779,7 +779,7 @@ __armv7_mmu_cache_on:
>> orrne r0, r0, #1 @ MMU enabled
>> movne r1, #0xfffffffd @ domain 0 = client
>> bic r6, r6, #1 << 31 @ 32-bit translation system
>
> Hmm, if TTBCR.EAE _was_ actually set...
>
>> - bic r6, r6, #3 << 0 @ use only ttbr0
>> + bic r6, r6, #(7 << 0) | (1 << 4) @ use only ttbr0
>> mcrne p15, 0, r3, c2, c0, 0 @ load page table pointer
>> mcrne p15, 0, r1, c3, c0, 0 @ load domain access control
>> mcrne p15, 0, r6, c2, c0, 2 @ load ttb control
>
> ...then strictly the TLBIALL needs to happen after the ISB following
> this update. Otherwise per B3.10.2 of DDI406C.c I think we might be into
> unpredictable territory - i.e. if the TLB happens to treat long- and
> short-descriptor entries differently then the TLBI beforehand (with EAE
> set) may be at liberty to only discard long-descriptor entries and leave
> bogus short-descriptor entries sitting around.
Yes, it seems this has to be taken care of, along with resetting
TTBCR.PD0 and TTBCR.N. Do you say that this needs to be done in the same
patch or a different one?
>
> In other words, something like (completely untested):
>
> ---8<---
> diff --git a/arch/arm/boot/compressed/head.S
> b/arch/arm/boot/compressed/head.S
> index af11c2f8f3b7..536b7781024a 100644
> --- a/arch/arm/boot/compressed/head.S
> +++ b/arch/arm/boot/compressed/head.S
> @@ -764,7 +764,6 @@ __armv7_mmu_cache_on:
> mov r0, #0
> mcr p15, 0, r0, c7, c10, 4 @ drain write buffer
> tst r11, #0xf @ VMSA
> - mcrne p15, 0, r0, c8, c7, 0 @ flush I,D TLBs
Shouldn't this be still there for the same reason you explained above? I
mean to discard the long descriptor entries when EAE was 1 (before we
reset it).
> #endif
> mrc p15, 0, r0, c1, c0, 0 @ read control reg
> bic r0, r0, #1 << 28 @ clear SCTLR.TRE
> @@ -783,8 +782,11 @@ __armv7_mmu_cache_on:
> mcrne p15, 0, r3, c2, c0, 0 @ load page table pointer
> mcrne p15, 0, r1, c3, c0, 0 @ load domain access control
> mcrne p15, 0, r6, c2, c0, 2 @ load ttb control
> -#endif
> mcr p15, 0, r0, c7, c5, 4 @ ISB
> + mcrne p15, 0, r0, c8, c7, 0 @ flush I,D TLBs
> +#else
> + mcr p15, 0, r0, c7, c5, 4 @ ISB
> +#endif
> mcr p15, 0, r0, c1, c0, 0 @ load control register
> mrc p15, 0, r0, c1, c0, 0 @ and read it back
> ---8<---
>
> Robin.
>
i have tested this change (flush I, D, TLBs after TTB control is
written) and don't see any issue. But on my setup decompression is
successful even without this (probably not hitting the case in discussion).
Thanks,
-- Srinivas R
--
Qualcomm India Private Limited, on behalf of Qualcomm Innovation Center,
Inc., is a member of Code Aurora Forum, a Linux Foundation Collaborative
Project.
More information about the linux-arm-kernel
mailing list