[RFC PATCH] net: stmmac: Add OXNAS Glue Driver

Joachim Eastwood manabian at gmail.com
Thu Oct 20 09:26:58 PDT 2016


Hi Neil,

On 20 October 2016 at 17:54, Neil Armstrong <narmstrong at baylibre.com> wrote:
> Add Synopsys Designware MAC Glue layer for the Oxford Semiconductor OX820.
>
> Signed-off-by: Neil Armstrong <narmstrong at baylibre.com>
> ---
>  .../devicetree/bindings/net/oxnas-dwmac.txt        |  44 ++++++
>  drivers/net/ethernet/stmicro/stmmac/Kconfig        |  11 ++
>  drivers/net/ethernet/stmicro/stmmac/Makefile       |   1 +
>  drivers/net/ethernet/stmicro/stmmac/dwmac-oxnas.c  | 173 +++++++++++++++++++++
>  4 files changed, 229 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/net/oxnas-dwmac.txt
>  create mode 100644 drivers/net/ethernet/stmicro/stmmac/dwmac-oxnas.c
<snip>
> +
> +static int oxnas_dwmac_probe(struct platform_device *pdev)
> +{
> +       struct plat_stmmacenet_data *plat_dat;
> +       struct stmmac_resources stmmac_res;
> +       struct device_node *sysctrl;
> +       struct oxnas_dwmac *dwmac;
> +       int ret;
> +
> +       sysctrl = of_parse_phandle(pdev->dev.of_node, "oxsemi,sys-ctrl", 0);
> +       if (!sysctrl) {
> +               dev_err(&pdev->dev, "failed to get sys-ctrl node\n");
> +               return -EINVAL;
> +       }
> +
> +       ret = stmmac_get_platform_resources(pdev, &stmmac_res);
> +       if (ret)
> +               return ret;
> +
> +       plat_dat = stmmac_probe_config_dt(pdev, &stmmac_res.mac);
> +       if (IS_ERR(plat_dat))
> +               return PTR_ERR(plat_dat);
> +
> +       dwmac = devm_kzalloc(&pdev->dev, sizeof(*dwmac), GFP_KERNEL);
> +       if (!dwmac)
> +               return -ENOMEM;
> +
> +       dwmac->regmap = syscon_node_to_regmap(sysctrl);
> +       if (IS_ERR(dwmac->regmap)) {
> +               dev_err(&pdev->dev, "failed to have sysctrl regmap\n");
> +               return PTR_ERR(dwmac->regmap);
> +       }
> +
> +       dwmac->clk = devm_clk_get(&pdev->dev, "gmac");
> +       if (IS_ERR(dwmac->clk))
> +               return PTR_ERR(dwmac->clk);
> +
> +       plat_dat->bsp_priv = dwmac;
> +       plat_dat->init = oxnas_dwmac_init;
> +       plat_dat->exit = oxnas_dwmac_exit;

Please do not use the init/exit callbacks. Implement proper driver
callbacks instead. I.e: PM resume/suspend and driver remove.

Shouldn't you call oxnas_dwmac_init() from probe as well?
As it is now it will only be called during PM resume and that can't be right.


> +
> +       return stmmac_dvr_probe(&pdev->dev, plat_dat, &stmmac_res);

If stmmac_dvr_probe() fails you should disable your clocks.


regards,
Joachim Eastwood



More information about the linux-arm-kernel mailing list