[RFC PATCH] net: stmmac: Add OXNAS Glue Driver
Neil Armstrong
narmstrong at baylibre.com
Thu Oct 20 08:54:06 PDT 2016
Add Synopsys Designware MAC Glue layer for the Oxford Semiconductor OX820.
Signed-off-by: Neil Armstrong <narmstrong at baylibre.com>
---
.../devicetree/bindings/net/oxnas-dwmac.txt | 44 ++++++
drivers/net/ethernet/stmicro/stmmac/Kconfig | 11 ++
drivers/net/ethernet/stmicro/stmmac/Makefile | 1 +
drivers/net/ethernet/stmicro/stmmac/dwmac-oxnas.c | 173 +++++++++++++++++++++
4 files changed, 229 insertions(+)
create mode 100644 Documentation/devicetree/bindings/net/oxnas-dwmac.txt
create mode 100644 drivers/net/ethernet/stmicro/stmmac/dwmac-oxnas.c
diff --git a/Documentation/devicetree/bindings/net/oxnas-dwmac.txt b/Documentation/devicetree/bindings/net/oxnas-dwmac.txt
new file mode 100644
index 0000000..5d2696c
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/oxnas-dwmac.txt
@@ -0,0 +1,44 @@
+* Oxford Semiconductor OXNAS DWMAC Ethernet controller
+
+The device inherits all the properties of the dwmac/stmmac devices
+described in the file stmmac.txt in the current directory with the
+following changes.
+
+Required properties on all platforms:
+
+- compatible: Depending on the platform this should be one of:
+ - "oxsemi,ox820-dwmac"
+ Additionally "snps,dwmac" and any applicable more
+ detailed version number described in net/stmmac.txt
+ should be used.
+
+- reg: The first register range should be the one of the DWMAC
+ controller.
+
+- clocks: Should contain phandles to the following clocks
+- clock-names: Should contain the following:
+ - "stmmaceth" - see stmmac.txt
+ - "gmac" - peripheral gate clock
+
+- oxsemi,sys-ctrl: a phandle to the system controller syscon node
+
+Example :
+
+etha: ethernet at 40400000 {
+ compatible = "oxsemi,ox820-dwmac", "snps,dwmac";
+ reg = <0x40400000 0x2000>;
+ interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "macirq", "eth_wake_irq";
+ mac-address = [000000000000]; /* Filled in by U-Boot */
+ phy-mode = "rgmii";
+
+ clocks = <&stdclk CLK_820_ETHA>, <&gmacclk>;
+ clock-names = "gmac", "stmmaceth";
+ resets = <&reset RESET_MAC>;
+
+ /* Regmap for sys registers */
+ oxsemi,sys-ctrl = <&sys>;
+
+ status = "disabled";
+};
diff --git a/drivers/net/ethernet/stmicro/stmmac/Kconfig b/drivers/net/ethernet/stmicro/stmmac/Kconfig
index 3818c5e..27ed913 100644
--- a/drivers/net/ethernet/stmicro/stmmac/Kconfig
+++ b/drivers/net/ethernet/stmicro/stmmac/Kconfig
@@ -62,6 +62,7 @@ config DWMAC_MESON
tristate "Amlogic Meson dwmac support"
default ARCH_MESON
depends on OF && COMMON_CLK && (ARCH_MESON || COMPILE_TEST)
+ select MFD_SYSCON
help
Support for Ethernet controller on Amlogic Meson SoCs.
@@ -69,6 +70,16 @@ config DWMAC_MESON
the stmmac device driver. This driver is used for Meson6,
Meson8, Meson8b and GXBB SoCs.
+config DWMAC_OXNAS
+ tristate "Oxford Semiconductor OXNAS dwmac support"
+ default ARCH_OXNAS
+ depends on OF && COMMON_CLK && (ARCH_OXNAS || COMPILE_TEST)
+ help
+ Support for Ethernet controller on Oxford Semiconductor OXNAS SoCs.
+
+ This selects the Oxford Semiconductor OXNASSoC glue layer support for
+ the stmmac device driver. This driver is used for OX820.
+
config DWMAC_ROCKCHIP
tristate "Rockchip dwmac support"
default ARCH_ROCKCHIP
diff --git a/drivers/net/ethernet/stmicro/stmmac/Makefile b/drivers/net/ethernet/stmicro/stmmac/Makefile
index 5d6ece5..8f83a86 100644
--- a/drivers/net/ethernet/stmicro/stmmac/Makefile
+++ b/drivers/net/ethernet/stmicro/stmmac/Makefile
@@ -10,6 +10,7 @@ obj-$(CONFIG_STMMAC_PLATFORM) += stmmac-platform.o
obj-$(CONFIG_DWMAC_IPQ806X) += dwmac-ipq806x.o
obj-$(CONFIG_DWMAC_LPC18XX) += dwmac-lpc18xx.o
obj-$(CONFIG_DWMAC_MESON) += dwmac-meson.o dwmac-meson8b.o
+obj-$(CONFIG_DWMAC_OXNAS) += dwmac-oxnas.o
obj-$(CONFIG_DWMAC_ROCKCHIP) += dwmac-rk.o
obj-$(CONFIG_DWMAC_SOCFPGA) += dwmac-altr-socfpga.o
obj-$(CONFIG_DWMAC_STI) += dwmac-sti.o
diff --git a/drivers/net/ethernet/stmicro/stmmac/dwmac-oxnas.c b/drivers/net/ethernet/stmicro/stmmac/dwmac-oxnas.c
new file mode 100644
index 0000000..c65f3a6
--- /dev/null
+++ b/drivers/net/ethernet/stmicro/stmmac/dwmac-oxnas.c
@@ -0,0 +1,173 @@
+/*
+ * Oxford Semiconductor OXNAS DWMAC glue layer
+ *
+ * Copyright (C) 2016 Neil Armstrong <narmstrong at baylibre.com>
+ * Copyright (C) 2014 Daniel Golle <daniel at makrotopia.org>
+ * Copyright (C) 2013 Ma Haijun <mahaijuns at gmail.com>
+ * Copyright (C) 2012 John Crispin <blogic at openwrt.org>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program. If not, see <http://www.gnu.org/licenses/>.
+ */
+
+#include <linux/device.h>
+#include <linux/io.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+#include <linux/mfd/syscon.h>
+#include <linux/stmmac.h>
+
+#include "stmmac_platform.h"
+
+/* System Control regmap offsets */
+#define OXNAS_DWMAC_CTRL_REGOFFSET 0x78
+#define OXNAS_DWMAC_DELAY_REGOFFSET 0x100
+
+/* Control Register */
+#define DWMAC_CKEN_RX_IN 14
+#define DWMAC_CKEN_RXN_OUT 13
+#define DWMAC_CKEN_RX_OUT 12
+#define DWMAC_CKEN_TX_IN 10
+#define DWMAC_CKEN_TXN_OUT 9
+#define DWMAC_CKEN_TX_OUT 8
+#define DWMAC_RX_SOURCE 7
+#define DWMAC_TX_SOURCE 6
+#define DWMAC_LOW_TX_SOURCE 4
+#define DWMAC_AUTO_TX_SOURCE 3
+#define DWMAC_RGMII 2
+#define DWMAC_SIMPLE_MUX 1
+#define DWMAC_CKEN_GTX 0
+
+/* Delay register */
+#define DWMAC_TX_VARDELAY_SHIFT 0
+#define DWMAC_TXN_VARDELAY_SHIFT 8
+#define DWMAC_RX_VARDELAY_SHIFT 16
+#define DWMAC_RXN_VARDELAY_SHIFT 24
+#define DWMAC_TX_VARDELAY(d) ((d) << DWMAC_TX_VARDELAY_SHIFT)
+#define DWMAC_TXN_VARDELAY(d) ((d) << DWMAC_TXN_VARDELAY_SHIFT)
+#define DWMAC_RX_VARDELAY(d) ((d) << DWMAC_RX_VARDELAY_SHIFT)
+#define DWMAC_RXN_VARDELAY(d) ((d) << DWMAC_RXN_VARDELAY_SHIFT)
+
+struct oxnas_dwmac {
+ struct clk *clk;
+ struct regmap *regmap;
+};
+
+static int oxnas_dwmac_init(struct platform_device *pdev, void *priv)
+{
+ struct oxnas_dwmac *dwmac = priv;
+ unsigned int value;
+ int ret;
+
+ /* Reset HW here before changing the glue configuration */
+ ret = device_reset(&pdev->dev);
+ if (ret)
+ return ret;
+
+ clk_prepare_enable(dwmac->clk);
+
+ ret = regmap_read(dwmac->regmap, OXNAS_DWMAC_CTRL_REGOFFSET, &value);
+ if (ret < 0)
+ return ret;
+
+ /* Enable GMII_GTXCLK to follow GMII_REFCLK, required for gigabit PHY */
+ value |= BIT(DWMAC_CKEN_GTX);
+ /* Use simple mux for 25/125 Mhz clock switching */
+ value |= BIT(DWMAC_SIMPLE_MUX);
+ /* set auto switch tx clock source */
+ value |= BIT(DWMAC_AUTO_TX_SOURCE);
+ /* enable tx & rx vardelay */
+ value |= BIT(DWMAC_CKEN_TX_OUT);
+ value |= BIT(DWMAC_CKEN_TXN_OUT);
+ value |= BIT(DWMAC_CKEN_TX_IN);
+ value |= BIT(DWMAC_CKEN_RX_OUT);
+ value |= BIT(DWMAC_CKEN_RXN_OUT);
+ value |= BIT(DWMAC_CKEN_RX_IN);
+ regmap_write(dwmac->regmap, OXNAS_DWMAC_CTRL_REGOFFSET, value);
+
+ /* set tx & rx vardelay */
+ value = DWMAC_TX_VARDELAY(4);
+ value |= DWMAC_TXN_VARDELAY(2);
+ value |= DWMAC_RX_VARDELAY(10);
+ value |= DWMAC_RXN_VARDELAY(8);
+ regmap_write(dwmac->regmap, OXNAS_DWMAC_DELAY_REGOFFSET, value);
+
+ return 0;
+}
+
+static void oxnas_dwmac_exit(struct platform_device *pdev, void *priv)
+{
+ struct oxnas_dwmac *dwmac = priv;
+
+ clk_disable_unprepare(dwmac->clk);
+}
+
+static int oxnas_dwmac_probe(struct platform_device *pdev)
+{
+ struct plat_stmmacenet_data *plat_dat;
+ struct stmmac_resources stmmac_res;
+ struct device_node *sysctrl;
+ struct oxnas_dwmac *dwmac;
+ int ret;
+
+ sysctrl = of_parse_phandle(pdev->dev.of_node, "oxsemi,sys-ctrl", 0);
+ if (!sysctrl) {
+ dev_err(&pdev->dev, "failed to get sys-ctrl node\n");
+ return -EINVAL;
+ }
+
+ ret = stmmac_get_platform_resources(pdev, &stmmac_res);
+ if (ret)
+ return ret;
+
+ plat_dat = stmmac_probe_config_dt(pdev, &stmmac_res.mac);
+ if (IS_ERR(plat_dat))
+ return PTR_ERR(plat_dat);
+
+ dwmac = devm_kzalloc(&pdev->dev, sizeof(*dwmac), GFP_KERNEL);
+ if (!dwmac)
+ return -ENOMEM;
+
+ dwmac->regmap = syscon_node_to_regmap(sysctrl);
+ if (IS_ERR(dwmac->regmap)) {
+ dev_err(&pdev->dev, "failed to have sysctrl regmap\n");
+ return PTR_ERR(dwmac->regmap);
+ }
+
+ dwmac->clk = devm_clk_get(&pdev->dev, "gmac");
+ if (IS_ERR(dwmac->clk))
+ return PTR_ERR(dwmac->clk);
+
+ plat_dat->bsp_priv = dwmac;
+ plat_dat->init = oxnas_dwmac_init;
+ plat_dat->exit = oxnas_dwmac_exit;
+
+ return stmmac_dvr_probe(&pdev->dev, plat_dat, &stmmac_res);
+}
+
+static const struct of_device_id oxnas_dwmac_match[] = {
+ { .compatible = "oxsemi,ox820-dwmac" },
+ { }
+};
+MODULE_DEVICE_TABLE(of, oxnas_dwmac_match);
+
+static struct platform_driver oxnas_dwmac_driver = {
+ .probe = oxnas_dwmac_probe,
+ .remove = stmmac_pltfr_remove,
+ .driver = {
+ .name = "oxnas-dwmac",
+ .pm = &stmmac_pltfr_pm_ops,
+ .of_match_table = oxnas_dwmac_match,
+ },
+};
+module_platform_driver(oxnas_dwmac_driver);
+
+MODULE_AUTHOR("Neil Armstrong <narmstrong at baylibre.com>");
+MODULE_DESCRIPTION("Oxford Semiconductor OXNAS DWMAC glue layer");
+MODULE_LICENSE("GPL v2");
--
2.7.0
More information about the linux-arm-kernel
mailing list