[PATCH][v2] arm64: Add DTS support for FSL's LS1012A SoC
Harninder Rai
harninder.rai at nxp.com
Wed Nov 16 10:24:07 PST 2016
LS1012A features an advanced 64-bit ARM v8 CortexA53 processor
with 32 KB of parity protected L1-I cache, 32 KB of ECC protected
L1-D cache, as well as 256 KB of ECC protected L2 cache.
Features summary
One 64-bit ARM-v8 Cortex-A53 core with the following capabilities
- Arranged as a cluster of one core supporting a 256 KB L2 cache with ECC
protection
- Speed up to 800 MHz
- Parity-protected 32 KB L1 instruction cache and 32 KB L1 data cache
- Neon SIMD engine
- ARM v8 cryptography extensions
One 16-bit DDR3L SDRAM memory controller
ARM core-link CCI-400 cache coherent interconnect
Cryptography acceleration (SEC)
One Configurable x3 SerDes
One PCI Express Gen2 controller, supporting x1 operation
One serial ATA (SATA Gen 3.0) controller
One USB 3.0/2.0 controller with integrated PHY
Following levels of DTSI/DTS files have been created for the LS1012A
SoC family:
- fsl-ls1012a.dtsi:
DTS-Include file for FSL LS1012A SoC.
- fsl-ls1012a-frdm.dts:
DTS file for FSL LS1012A FRDM board.
- fsl-ls1012a-qds.dts:
DTS file for FSL LS1012A QDS board.
- fsl-ls1012a-rdb.dts:
DTS file for FSL LS1012A RDB board.
Signed-off-by: Harninder Rai <harninder.rai at nxp.com>
Signed-off-by: Bhaskar Upadhaya <Bhaskar.Upadhaya at nxp.com>
---
Changes in v2: Incorporated Shawn's comments
- Brief introduction of the SoC in commit message
- Alphabetic ordering of labeled nodes
- Better naming to be used for regulator node
- Make timer node's comments more readable
- Sort nodes with unit-address in order of the address
arch/arm64/boot/dts/freescale/Makefile | 3 +
arch/arm64/boot/dts/freescale/fsl-ls1012a-frdm.dts | 115 ++++++++++
arch/arm64/boot/dts/freescale/fsl-ls1012a-qds.dts | 128 +++++++++++
arch/arm64/boot/dts/freescale/fsl-ls1012a-rdb.dts | 59 +++++
arch/arm64/boot/dts/freescale/fsl-ls1012a.dtsi | 245 +++++++++++++++++++++
5 files changed, 550 insertions(+)
create mode 100644 arch/arm64/boot/dts/freescale/fsl-ls1012a-frdm.dts
create mode 100644 arch/arm64/boot/dts/freescale/fsl-ls1012a-qds.dts
create mode 100644 arch/arm64/boot/dts/freescale/fsl-ls1012a-rdb.dts
create mode 100644 arch/arm64/boot/dts/freescale/fsl-ls1012a.dtsi
diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile
index 6602718..39db645 100644
--- a/arch/arm64/boot/dts/freescale/Makefile
+++ b/arch/arm64/boot/dts/freescale/Makefile
@@ -1,3 +1,6 @@
+dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls1012a-frdm.dtb
+dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls1012a-qds.dtb
+dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls1012a-rdb.dtb
dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls1043a-qds.dtb
dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls1043a-rdb.dtb
dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls1046a-qds.dtb
diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1012a-frdm.dts b/arch/arm64/boot/dts/freescale/fsl-ls1012a-frdm.dts
new file mode 100644
index 0000000..81bd689
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/fsl-ls1012a-frdm.dts
@@ -0,0 +1,115 @@
+/*
+ * Device Tree file for Freescale LS1012A Freedom Board.
+ *
+ * Copyright 2016, Freescale Semiconductor
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPLv2 or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This library is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This library is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+/dts-v1/;
+
+#include "fsl-ls1012a.dtsi"
+
+/ {
+ model = "LS1012A Freedom Board";
+ compatible = "fsl,ls1012a-frdm", "fsl,ls1012a";
+
+ sys_mclk: clock-mclk {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <25000000>;
+ };
+
+ regulator_1p8v: regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "1P8V";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ };
+
+ sound {
+ compatible = "simple-audio-card";
+ simple-audio-card,format = "i2s";
+ simple-audio-card,widgets =
+ "Microphone", "Microphone Jack",
+ "Headphone", "Headphone Jack",
+ "Speaker", "Speaker Ext",
+ "Line", "Line In Jack";
+ simple-audio-card,routing =
+ "MIC_IN", "Microphone Jack",
+ "Microphone Jack", "Mic Bias",
+ "LINE_IN", "Line In Jack",
+ "Headphone Jack", "HP_OUT",
+ "Speaker Ext", "LINE_OUT";
+
+ simple-audio-card,cpu {
+ sound-dai = <&sai2>;
+ frame-master;
+ bitclock-master;
+ };
+
+ simple-audio-card,codec {
+ sound-dai = <&codec>;
+ frame-master;
+ bitclock-master;
+ system-clock-frequency = <25000000>;
+ };
+ };
+};
+
+&duart0 {
+ status = "okay";
+};
+
+&i2c0 {
+ status = "okay";
+
+ codec: sgtl5000 at a {
+ #sound-dai-cells = <0>;
+ compatible = "fsl,sgtl5000";
+ reg = <0xa>;
+ VDDA-supply = <®ulator_1p8v>;
+ VDDIO-supply = <®ulator_1p8v>;
+ clocks = <&sys_mclk>;
+ };
+};
+
+&sai2 {
+ status = "okay";
+};
diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1012a-qds.dts b/arch/arm64/boot/dts/freescale/fsl-ls1012a-qds.dts
new file mode 100644
index 0000000..b841251
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/fsl-ls1012a-qds.dts
@@ -0,0 +1,128 @@
+/*
+ * Device Tree file for Freescale LS1012A QDS Board.
+ *
+ * Copyright 2016, Freescale Semiconductor
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPLv2 or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This library is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This library is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+/dts-v1/;
+
+#include "fsl-ls1012a.dtsi"
+
+/ {
+ model = "LS1012A QDS Board";
+ compatible = "fsl,ls1012a-qds", "fsl,ls1012a";
+
+ sys_mclk: clock-mclk {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <24576000>;
+ };
+
+ regulator_3p3v: regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "3P3V";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ sound {
+ compatible = "simple-audio-card";
+ simple-audio-card,format = "i2s";
+ simple-audio-card,widgets =
+ "Microphone", "Microphone Jack",
+ "Headphone", "Headphone Jack",
+ "Speaker", "Speaker Ext",
+ "Line", "Line In Jack";
+ simple-audio-card,routing =
+ "MIC_IN", "Microphone Jack",
+ "Microphone Jack", "Mic Bias",
+ "LINE_IN", "Line In Jack",
+ "Headphone Jack", "HP_OUT",
+ "Speaker Ext", "LINE_OUT";
+
+ simple-audio-card,cpu {
+ sound-dai = <&sai2>;
+ frame-master;
+ bitclock-master;
+ };
+
+ simple-audio-card,codec {
+ sound-dai = <&codec>;
+ frame-master;
+ bitclock-master;
+ system-clock-frequency = <24576000>;
+ };
+ };
+};
+
+&duart0 {
+ status = "okay";
+};
+
+&i2c0 {
+ status = "okay";
+
+ pca9547 at 77 {
+ compatible = "nxp,pca9547";
+ reg = <0x77>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ i2c at 4 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x4>;
+
+ codec: sgtl5000 at a {
+ #sound-dai-cells = <0>;
+ compatible = "fsl,sgtl5000";
+ reg = <0xa>;
+ VDDA-supply = <®ulator_3p3v>;
+ VDDIO-supply = <®ulator_3p3v>;
+ clocks = <&sys_mclk>;
+ };
+ };
+ };
+};
+
+&sai2 {
+ status = "okay";
+};
diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1012a-rdb.dts b/arch/arm64/boot/dts/freescale/fsl-ls1012a-rdb.dts
new file mode 100644
index 0000000..62c5c71
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/fsl-ls1012a-rdb.dts
@@ -0,0 +1,59 @@
+/*
+ * Device Tree file for Freescale LS1012A RDB Board.
+ *
+ * Copyright 2016, Freescale Semiconductor
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPLv2 or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This library is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This library is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+/dts-v1/;
+
+#include "fsl-ls1012a.dtsi"
+
+/ {
+ model = "LS1012A RDB Board";
+ compatible = "fsl,ls1012a-rdb", "fsl,ls1012a";
+};
+
+&duart0 {
+ status = "okay";
+};
+
+&i2c0 {
+ status = "okay";
+};
diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1012a.dtsi b/arch/arm64/boot/dts/freescale/fsl-ls1012a.dtsi
new file mode 100644
index 0000000..24874d7
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/fsl-ls1012a.dtsi
@@ -0,0 +1,245 @@
+/*
+ * Device Tree Include file for Freescale Layerscape-1012A family SoC.
+ *
+ * Copyright 2016, Freescale Semiconductor
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPLv2 or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This library is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This library is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+#include <dt-bindings/interrupt-controller/irq.h>
+
+/ {
+ compatible = "fsl,ls1012a";
+ interrupt-parent = <&gic>;
+ #address-cells = <2>;
+ #size-cells = <2>;
+
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ cpu0: cpu at 0 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a53";
+ reg = <0x0>;
+ clocks = <&clockgen 1 0>;
+ #cooling-cells = <2>;
+ };
+ };
+
+ sysclk: sysclk {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <100000000>;
+ clock-output-names = "sysclk";
+ };
+
+ timer {
+ compatible = "arm,armv8-timer";
+
+ interrupts = <1 13 IRQ_TYPE_LEVEL_LOW>,/* Physical Secure PPI */
+ <1 14 IRQ_TYPE_LEVEL_LOW>,/* Physical Non-Secure PPI */
+ <1 11 IRQ_TYPE_LEVEL_LOW>,/* Virtual PPI */
+ <1 10 IRQ_TYPE_LEVEL_LOW>;/* Hypervisor PPI */
+ };
+
+ pmu {
+ compatible = "arm,armv8-pmuv3";
+ interrupts = <0 106 IRQ_TYPE_LEVEL_LOW>;
+ };
+
+ gic: interrupt-controller at 1400000 {
+ compatible = "arm,gic-400";
+ #interrupt-cells = <3>;
+ interrupt-controller;
+ reg = <0x0 0x1401000 0 0x1000>, /* GICD */
+ <0x0 0x1402000 0 0x2000>, /* GICC */
+ <0x0 0x1404000 0 0x2000>, /* GICH */
+ <0x0 0x1406000 0 0x2000>; /* GICV */
+ interrupts = <1 9 IRQ_TYPE_LEVEL_LOW>;
+ };
+
+ reboot {
+ compatible = "syscon-reboot";
+ regmap = <&dcfg>;
+ offset = <0xb0>;
+ mask = <0x02>;
+ };
+
+ soc {
+ compatible = "simple-bus";
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+
+ scfg: scfg at 1570000 {
+ compatible = "fsl,ls1012a-scfg", "syscon";
+ reg = <0x0 0x1570000 0x0 0x10000>;
+ big-endian;
+ };
+
+ dcfg: dcfg at 1ee0000 {
+ compatible = "fsl,ls1012a-dcfg",
+ "syscon";
+ reg = <0x0 0x1ee0000 0x0 0x10000>;
+ big-endian;
+ };
+
+ clockgen: clocking at 1ee1000 {
+ compatible = "fsl,ls1012a-clockgen";
+ reg = <0x0 0x1ee1000 0x0 0x1000>;
+ #clock-cells = <2>;
+ clocks = <&sysclk>;
+ };
+
+ i2c0: i2c at 2180000 {
+ compatible = "fsl,vf610-i2c";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x0 0x2180000 0x0 0x10000>;
+ interrupts = <0 56 IRQ_TYPE_LEVEL_LOW>;
+ clocks = <&clockgen 4 0>;
+ status = "disabled";
+ };
+
+ i2c1: i2c at 2190000 {
+ compatible = "fsl,vf610-i2c";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x0 0x2190000 0x0 0x10000>;
+ interrupts = <0 57 IRQ_TYPE_LEVEL_LOW>;
+ clocks = <&clockgen 4 0>;
+ status = "disabled";
+ };
+
+ duart0: serial at 21c0500 {
+ compatible = "fsl,ns16550", "ns16550a";
+ reg = <0x00 0x21c0500 0x0 0x100>;
+ interrupts = <0 54 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clockgen 4 0>;
+ };
+
+ duart1: serial at 21c0600 {
+ compatible = "fsl,ns16550", "ns16550a";
+ reg = <0x00 0x21c0600 0x0 0x100>;
+ interrupts = <0 54 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clockgen 4 0>;
+ };
+
+ gpio0: gpio at 2300000 {
+ compatible = "fsl,qoriq-gpio";
+ reg = <0x0 0x2300000 0x0 0x10000>;
+ interrupts = <0 66 IRQ_TYPE_LEVEL_LOW>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpio1: gpio at 2310000 {
+ compatible = "fsl,qoriq-gpio";
+ reg = <0x0 0x2310000 0x0 0x10000>;
+ interrupts = <0 67 IRQ_TYPE_LEVEL_LOW>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ wdog0: wdog at 2ad0000 {
+ compatible = "fsl,ls1012a-wdt",
+ "fsl,imx21-wdt";
+ reg = <0x0 0x2ad0000 0x0 0x10000>;
+ interrupts = <0 83 IRQ_TYPE_LEVEL_LOW>;
+ clocks = <&clockgen 4 0>;
+ big-endian;
+ };
+
+ sai1: sai at 2b50000 {
+ #sound-dai-cells = <0>;
+ compatible = "fsl,vf610-sai";
+ reg = <0x0 0x2b50000 0x0 0x10000>;
+ interrupts = <0 148 IRQ_TYPE_LEVEL_LOW>;
+ clocks = <&clockgen 4 3>, <&clockgen 4 3>,
+ <&clockgen 4 3>, <&clockgen 4 3>;
+ clock-names = "bus", "mclk1", "mclk2", "mclk3";
+ dma-names = "tx", "rx";
+ dmas = <&edma0 1 47>,
+ <&edma0 1 46>;
+ status = "disabled";
+ };
+
+ sai2: sai at 2b60000 {
+ #sound-dai-cells = <0>;
+ compatible = "fsl,vf610-sai";
+ reg = <0x0 0x2b60000 0x0 0x10000>;
+ interrupts = <0 149 IRQ_TYPE_LEVEL_LOW>;
+ clocks = <&clockgen 4 3>, <&clockgen 4 3>,
+ <&clockgen 4 3>, <&clockgen 4 3>;
+ clock-names = "bus", "mclk1", "mclk2", "mclk3";
+ dma-names = "tx", "rx";
+ dmas = <&edma0 1 45>,
+ <&edma0 1 44>;
+ status = "disabled";
+ };
+
+ edma0: edma at 2c00000 {
+ #dma-cells = <2>;
+ compatible = "fsl,vf610-edma";
+ reg = <0x0 0x2c00000 0x0 0x10000>,
+ <0x0 0x2c10000 0x0 0x10000>,
+ <0x0 0x2c20000 0x0 0x10000>;
+ interrupts = <0 103 IRQ_TYPE_LEVEL_LOW>,
+ <0 103 IRQ_TYPE_LEVEL_LOW>;
+ interrupt-names = "edma-tx", "edma-err";
+ dma-channels = <32>;
+ big-endian;
+ clock-names = "dmamux0", "dmamux1";
+ clocks = <&clockgen 4 3>,
+ <&clockgen 4 3>;
+ };
+
+ sata: sata at 3200000 {
+ compatible = "fsl,ls1012a-ahci", "fsl,ls1043a-ahci";
+ reg = <0x0 0x3200000 0x0 0x10000>;
+ interrupts = <0 69 IRQ_TYPE_LEVEL_LOW>;
+ clocks = <&clockgen 4 0>;
+ };
+ };
+};
--
1.9.1
More information about the linux-arm-kernel
mailing list