[PATCH 3/3] ARM: dts: Add gyro and accel to APQ8060 Dragonboard

Bjorn Andersson bjorn.andersson at linaro.org
Thu Nov 3 14:54:53 PDT 2016


On Thu 03 Nov 02:13 PDT 2016, Linus Walleij wrote:

> This adds the MPU-3050 gyroscope and the KXSD9 accelerometer to
> the Qualcomm APQ8060 Dragonboard. The KXSD9 is mounted beyond the
> MPU-3050 and appear as a subdevice beyond it. We set up the
> required GPIO and interrupt lines to make the devices work.
> 
> Signed-off-by: Linus Walleij <linus.walleij at linaro.org>

I still would have preferred you using interrupts-extended when you're
specifying both parent and irq specifier anyways, but I'm ok with this.

Acked-by: Bjorn Andersson <bjorn.andersson at linaro.org>

Regards,
Bjorn

> ---
> ChangeLog v2->v3:
> - Move the interrupt to the pm8058 alias to reflect the two patches
>   properly specifying the PMIC as interrupt parent.
> ChangeLog v1->v2:
> - Use the new I2C mux gate bindings from Peter Rosin (merged to
>   the I2C subsystem)
> ---
>  arch/arm/boot/dts/qcom-apq8060-dragonboard.dts | 53 ++++++++++++++++++++++++++
>  1 file changed, 53 insertions(+)
> 
> diff --git a/arch/arm/boot/dts/qcom-apq8060-dragonboard.dts b/arch/arm/boot/dts/qcom-apq8060-dragonboard.dts
> index ea660ffa03ea..c1b99c9cb318 100644
> --- a/arch/arm/boot/dts/qcom-apq8060-dragonboard.dts
> +++ b/arch/arm/boot/dts/qcom-apq8060-dragonboard.dts
> @@ -220,6 +220,14 @@
>  					function = "ebi2";
>  				};
>  			};
> +
> +			/* Interrupt line for the KXSD9 accelerometer */
> +			dragon_kxsd9_gpios: kxsd9 {
> +				irq {
> +					pins = "gpio57"; /* IRQ line */
> +					bias-pull-up;
> +				};
> +			};
>  		};
>  
>  		qcom,ssbi at 500000 {
> @@ -272,6 +280,15 @@
>  							power-source = <PM8058_GPIO_S3>;
>  						};
>  					};
> +					dragon_mpu3050_gpios: mpu3050-gpios {
> +						pinconf {
> +							pins = "gpio17";
> +							function = "normal";
> +							input-enable;
> +							bias-disable;
> +							power-source = <PM8058_GPIO_S3>;
> +						};
> +					};
>  					dragon_sdcc3_gpios: sdcc3-gpios {
>  						pinconf {
>  							pins = "gpio22";
> @@ -389,6 +406,42 @@
>  					vddd-supply = <&pm8058_lvs0>; // 1.8V
>  					vdda-supply = <&pm8058_l14>; // 2.85V
>  				};
> +				mpu3050 at 68 {
> +					compatible = "invensense,mpu3050";
> +					reg = <0x68>;
> +					/*
> +					 * GPIO17 has interrupt 208 on the
> +					 * PM8058, it is pulled high by a 10k
> +					 * resistor to VLOGIC so needs to be
> +					 * active low/falling edge.
> +					 */
> +					interrupt-parent = <&pm8058>;
> +					interrupts = <208 IRQ_TYPE_EDGE_FALLING>;
> +					pinctrl-names = "default";
> +					pinctrl-0 = <&dragon_mpu3050_gpios>;
> +					vlogic-supply = <&pm8058_lvs0>; // 1.8V
> +					vdd-supply = <&pm8058_l14>; // 2.85V
> +
> +					/*
> +					 * The MPU-3050 acts as a hub for the
> +					 * accelerometer.
> +					 */
> +					i2c-gate {
> +						#address-cells = <1>;
> +						#size-cells = <0>;
> +
> +						kxsd9 at 18 {
> +							compatible = "kionix,kxsd9";
> +							reg = <0x18>;
> +							interrupt-parent = <&tlmm>;
> +							interrupts = <57 IRQ_TYPE_EDGE_FALLING>;
> +							pinctrl-names = "default";
> +							pinctrl-0 = <&dragon_kxsd9_gpios>;
> +							iovdd-supply = <&pm8058_lvs0>; // 1.8V
> +							vdd-supply = <&pm8058_l14>; // 2.85V
> +						};
> +					};
> +				};
>  			};
>  		};
>  
> -- 
> 2.7.4
> 



More information about the linux-arm-kernel mailing list