[PATCH 2/4] arm64: dts: hip06: Append hns node

Wei Xu xuwei5 at hisilicon.com
Tue Jun 28 10:09:30 PDT 2016


Hi Kefeng,

On 28/06/2016 06:51, Kefeng Wang wrote:
> There are four ports(2 GE, 2 XGE) in D03 board, append
> relevant nodes for them.
> 
> Cc: Kejian Yan <yankejian at huawei.com>
> Cc: Yisen Zhuang <yisen.zhuang at huawei.com>
> Signed-off-by: Kefeng Wang <wangkefeng.wang at huawei.com>
> ---
>  arch/arm64/boot/dts/hisilicon/hip06-d03.dts |  16 +++
>  arch/arm64/boot/dts/hisilicon/hip06.dtsi    | 215 ++++++++++++++++++++++++++++
>  2 files changed, 231 insertions(+)
> 
> diff --git a/arch/arm64/boot/dts/hisilicon/hip06-d03.dts b/arch/arm64/boot/dts/hisilicon/hip06-d03.dts
> index f3e5323..5562cf4 100644
> --- a/arch/arm64/boot/dts/hisilicon/hip06-d03.dts
> +++ b/arch/arm64/boot/dts/hisilicon/hip06-d03.dts
> @@ -25,6 +25,22 @@
>  	chosen { };
>  };
>  
> +&eth0 {
> +	status = "ok";
> +};
> +
> +&eth1 {
> +	status = "ok";
> +};
> +
> +&eth2 {
> +	status = "ok";
> +};
> +
> +&eth3 {
> +	status = "ok";
> +};
> +
>  &usb_ohci {
>  	status = "ok";
>  };
> diff --git a/arch/arm64/boot/dts/hisilicon/hip06.dtsi b/arch/arm64/boot/dts/hisilicon/hip06.dtsi
> index 5927bc4..3eca430 100644
> --- a/arch/arm64/boot/dts/hisilicon/hip06.dtsi
> +++ b/arch/arm64/boot/dts/hisilicon/hip06.dtsi
> @@ -279,6 +279,18 @@
>  		};
>  	};
>  
> +	mbigen_dsa at c0080000 {
> +		compatible = "hisilicon,mbigen-v2";
> +		reg = <0x0 0xc0080000 0x0 0x10000>;
> +
> +		mbigen_dsaf0: intc_dsaf0 {
> +			msi-parent = <&its_dsa 0x40800>;
> +			interrupt-controller;
> +			#interrupt-cells = <2>;
> +			num-pins = <409>;
> +		};
> +	};
> +
>  	soc {
>  		compatible = "simple-bus";
>  		#address-cells = <2>;
> @@ -302,6 +314,209 @@
>  			dma-coherent;
>  			status = "disabled";
>  		};
> +
> +		peri_c_subctrl: sub_ctrl_c at 60000000 {
> +			compatible = "hisilicon,peri-c-subctrl","syscon";
> +			reg = <0 0x60000000 0x0 0x10000>;
> +		};
> +
> +		dsaf_subctrl: dsaf_subctrl at c0000000 {
> +			compatible = "hisilicon,dsaf-ctrl", "syscon";
> +			reg = <0x0 0xc0000000 0x0 0x10000>;
> +		};
> +
> +		serdes_ctrl: sds_ctrl at c2200000 {
> +			compatible = "hisilicon,serdes-syscon","syscon";
> +			reg = <0 0xc2200000 0x0 0x80000>;
> +		};

I found peri-c-subctrl, dsaf-ctrl and serdes-syscon are not documented
in the device tree binding documents.
I checked the net-next tree and also did not find it.
Could you check it as well?
Thanks!
The others is fine to me.

Best Regards,
Wei Xu

> +
> +		mdio at 603c0000 {
> +			compatible = "hisilicon,hns-mdio";
> +			reg = <0x0 0x603c0000 0x0 0x1000>;
> +			subctrl-vbase = <&peri_c_subctrl>;
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +
> +			phy0: ethernet-phy at 0 {
> +				compatible = "ethernet-phy-ieee802.3-c22";
> +				reg = <0>;
> +			};
> +
> +			phy1: ethernet-phy at 1 {
> +				compatible = "ethernet-phy-ieee802.3-c22";
> +				reg = <1>;
> +			};
> +		};
> +
> +		dsaf0: dsa at c7000000 {
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +			compatible = "hisilicon,hns-dsaf-v2";
> +			mode = "6port-16rss";
> +			reg = <0x0 0xc5000000 0x0 0x890000
> +			       0x0 0xc7000000 0x0 0x600000>;
> +			reg-names = "ppe-base", "dsaf-base";
> +			interrupt-parent = <&mbigen_dsaf0>;
> +			subctrl-syscon = <&dsaf_subctrl>;
> +			reset-field-offset = <0>;
> +			interrupts =
> +			<576 1>, <577 1>, <578 1>, <579 1>, <580 1>,
> +			<581 1>, <582 1>, <583 1>, <584 1>, <585 1>,
> +			<586 1>, <587 1>, <588 1>, <589 1>, <590 1>,
> +			<591 1>, <592 1>, <593 1>, <594 1>, <595 1>,
> +			<596 1>, <597 1>, <598 1>, <599 1>, <600 1>,
> +			<960 1>, <961 1>, <962 1>, <963 1>, <964 1>,
> +			<965 1>, <966 1>, <967 1>, <968 1>, <969 1>,
> +			<970 1>, <971 1>, <972 1>, <973 1>, <974 1>,
> +			<975 1>, <976 1>, <977 1>, <978 1>, <979 1>,
> +			<980 1>, <981 1>, <982 1>, <983 1>, <984 1>,
> +			<985 1>, <986 1>, <987 1>, <988 1>, <989 1>,
> +			<990 1>, <991 1>, <992 1>, <993 1>, <994 1>,
> +			<995 1>, <996 1>, <997 1>, <998 1>, <999 1>,
> +			<1000 1>, <1001 1>, <1002 1>, <1003 1>,	<1004 1>,
> +			<1005 1>, <1006 1>, <1007 1>, <1008 1>, <1009 1>,
> +			<1010 1>, <1011 1>, <1012 1>, <1013 1>, <1014 1>,
> +			<1015 1>, <1016 1>, <1017 1>, <1018 1>, <1019 1>,
> +			<1020 1>, <1021 1>, <1022 1>, <1023 1>, <1024 1>,
> +			<1025 1>, <1026 1>, <1027 1>, <1028 1>, <1029 1>,
> +			<1030 1>, <1031 1>, <1032 1>, <1033 1>,	<1034 1>,
> +			<1035 1>, <1036 1>, <1037 1>, <1038 1>, <1039 1>,
> +			<1040 1>, <1041 1>, <1042 1>, <1043 1>, <1044 1>,
> +			<1045 1>, <1046 1>, <1047 1>, <1048 1>, <1049 1>,
> +			<1050 1>, <1051 1>, <1052 1>, <1053 1>, <1054 1>,
> +			<1055 1>, <1056 1>, <1057 1>, <1058 1>, <1059 1>,
> +			<1060 1>, <1061 1>, <1062 1>, <1063 1>,	<1064 1>,
> +			<1065 1>, <1066 1>, <1067 1>, <1068 1>, <1069 1>,
> +			<1070 1>, <1071 1>, <1072 1>, <1073 1>, <1074 1>,
> +			<1075 1>, <1076 1>, <1077 1>, <1078 1>, <1079 1>,
> +			<1080 1>, <1081 1>, <1082 1>, <1083 1>, <1084 1>,
> +			<1085 1>, <1086 1>, <1087 1>, <1088 1>, <1089 1>,
> +			<1090 1>, <1091 1>, <1092 1>, <1093 1>,	<1094 1>,
> +			<1095 1>, <1096 1>, <1097 1>, <1098 1>, <1099 1>,
> +			<1100 1>, <1101 1>, <1102 1>, <1103 1>, <1104 1>,
> +			<1105 1>, <1106 1>, <1107 1>, <1108 1>, <1109 1>,
> +			<1110 1>, <1111 1>, <1112 1>, <1113 1>, <1114 1>,
> +			<1115 1>, <1116 1>, <1117 1>, <1118 1>, <1119 1>,
> +			<1120 1>, <1121 1>, <1122 1>, <1123 1>, <1124 1>,
> +			<1125 1>, <1126 1>, <1127 1>, <1128 1>, <1129 1>,
> +			<1130 1>, <1131 1>, <1132 1>, <1133 1>, <1134 1>,
> +			<1135 1>, <1136 1>, <1137 1>, <1138 1>, <1139 1>,
> +			<1140 1>, <1141 1>, <1142 1>, <1143 1>, <1144 1>,
> +			<1145 1>, <1146 1>, <1147 1>, <1148 1>, <1149 1>,
> +			<1150 1>, <1151 1>, <1152 1>, <1153 1>, <1154 1>,
> +			<1155 1>, <1156 1>, <1157 1>, <1158 1>, <1159 1>,
> +			<1160 1>, <1161 1>, <1162 1>, <1163 1>, <1164 1>,
> +			<1165 1>, <1166 1>, <1167 1>, <1168 1>, <1169 1>,
> +			<1170 1>, <1171 1>, <1172 1>, <1173 1>, <1174 1>,
> +			<1175 1>, <1176 1>, <1177 1>, <1178 1>, <1179 1>,
> +			<1180 1>, <1181 1>, <1182 1>, <1183 1>, <1184 1>,
> +			<1185 1>, <1186 1>, <1187 1>, <1188 1>, <1189 1>,
> +			<1190 1>, <1191 1>, <1192 1>, <1193 1>, <1194 1>,
> +			<1195 1>, <1196 1>, <1197 1>, <1198 1>, <1199 1>,
> +			<1200 1>, <1201 1>, <1202 1>, <1203 1>, <1204 1>,
> +			<1205 1>, <1206 1>, <1207 1>, <1208 1>, <1209 1>,
> +			<1210 1>, <1211 1>, <1212 1>, <1213 1>, <1214 1>,
> +			<1215 1>, <1216 1>, <1217 1>, <1218 1>, <1219 1>,
> +			<1220 1>, <1221 1>, <1222 1>, <1223 1>, <1224 1>,
> +			<1225 1>, <1226 1>, <1227 1>, <1228 1>, <1229 1>,
> +			<1230 1>, <1231 1>, <1232 1>, <1233 1>, <1234 1>,
> +			<1235 1>, <1236 1>, <1237 1>, <1238 1>, <1239 1>,
> +			<1240 1>, <1241 1>, <1242 1>, <1243 1>, <1244 1>,
> +			<1245 1>, <1246 1>, <1247 1>, <1248 1>, <1249 1>,
> +			<1250 1>, <1251 1>, <1252 1>, <1253 1>, <1254 1>,
> +			<1255 1>, <1256 1>, <1257 1>, <1258 1>, <1259 1>,
> +			<1260 1>, <1261 1>, <1262 1>, <1263 1>, <1264 1>,
> +			<1265 1>, <1266 1>, <1267 1>, <1268 1>, <1269 1>,
> +			<1270 1>, <1271 1>, <1272 1>, <1273 1>, <1274 1>,
> +			<1275 1>, <1276 1>, <1277 1>, <1278 1>, <1279 1>,
> +			<1280 1>, <1281 1>, <1282 1>, <1283 1>, <1284 1>,
> +			<1285 1>, <1286 1>, <1287 1>, <1288 1>, <1289 1>,
> +			<1290 1>, <1291 1>, <1292 1>, <1293 1>, <1294 1>,
> +			<1295 1>, <1296 1>, <1297 1>, <1298 1>, <1299 1>,
> +			<1300 1>, <1301 1>, <1302 1>, <1303 1>, <1304 1>,
> +			<1305 1>, <1306 1>, <1307 1>, <1308 1>, <1309 1>,
> +			<1310 1>, <1311 1>, <1312 1>, <1313 1>, <1314 1>,
> +			<1315 1>, <1316 1>, <1317 1>, <1318 1>, <1319 1>,
> +			<1320 1>, <1321 1>, <1322 1>, <1323 1>, <1324 1>,
> +			<1325 1>, <1326 1>, <1327 1>, <1328 1>, <1329 1>,
> +			<1330 1>, <1331 1>, <1332 1>, <1333 1>, <1334 1>,
> +			<1335 1>, <1336 1>, <1337 1>, <1338 1>, <1339 1>,
> +			<1340 1>, <1341 1>, <1342 1>, <1343 1>;
> +
> +			desc-num = <0x400>;
> +			buf-size = <0x1000>;
> +			dma-coherent;
> +
> +			port at 0 {
> +				reg = <0>;
> +				serdes-syscon = <&serdes_ctrl>;
> +				port-rst-offset = <0>;
> +				port-mode-offset = <0>;
> +				media-type = "fiber";
> +			};
> +
> +			port at 1 {
> +				reg = <1>;
> +				serdes-syscon= <&serdes_ctrl>;
> +				port-rst-offset = <1>;
> +				port-mode-offset = <1>;
> +				media-type = "fiber";
> +			};
> +
> +			port at 4 {
> +				reg = <4>;
> +				phy-handle = <&phy0>;
> +				serdes-syscon= <&serdes_ctrl>;
> +				port-rst-offset = <4>;
> +				port-mode-offset = <2>;
> +				media-type = "copper";
> +			};
> +
> +			port at 5 {
> +				reg = <5>;
> +				phy-handle = <&phy1>;
> +				serdes-syscon= <&serdes_ctrl>;
> +				port-rst-offset = <5>;
> +				port-mode-offset = <3>;
> +				media-type = "copper";
> +			};
> +		};
> +
> +		eth0: ethernet at 4{
> +			compatible = "hisilicon,hns-nic-v2";
> +			ae-handle = <&dsaf0>;
> +			port-idx-in-ae = <4>;
> +			local-mac-address = [00 00 00 00 00 00];
> +			status = "disabled";
> +			dma-coherent;
> +		};
> +
> +		eth1: ethernet at 5{
> +			compatible = "hisilicon,hns-nic-v2";
> +			ae-handle = <&dsaf0>;
> +			port-idx-in-ae = <5>;
> +			local-mac-address = [00 00 00 00 00 00];
> +			status = "disabled";
> +			dma-coherent;
> +		};
> +
> +		eth2: ethernet at 0{
> +			compatible = "hisilicon,hns-nic-v2";
> +			ae-handle = <&dsaf0>;
> +			port-idx-in-ae = <0>;
> +			local-mac-address = [00 00 00 00 00 00];
> +			status = "disabled";
> +			dma-coherent;
> +		};
> +
> +		eth3: ethernet at 1{
> +			compatible = "hisilicon,hns-nic-v2";
> +			ae-handle = <&dsaf0>;
> +			port-idx-in-ae = <1>;
> +			local-mac-address = [00 00 00 00 00 00];
> +			status = "disabled";
> +			dma-coherent;
> +		};
>  	};
>  
>  };
> 




More information about the linux-arm-kernel mailing list