[PATCH v2 2/2] ARM: dts: imx6: Add support for Toradex Ixora carrier board
Stefan Agner
stefan at agner.ch
Wed Jan 6 22:38:24 PST 2016
Hi Marcel,
On 2016-01-05 08:39, Marcel Ziswiler wrote:
> From: Petr Štetiar <ynezz at true.cz>
>
> Signed-off-by: Petr Štetiar <ynezz at true.cz>
> Signed-off-by: Marcel Ziswiler <marcel.ziswiler at toradex.com>
> ---
>
> Changes in v2: None
>
> arch/arm/boot/dts/Makefile | 1 +
> arch/arm/boot/dts/imx6q-apalis-ixora.dts | 256 +++++++++++++++++++++++++++++++
> 2 files changed, 257 insertions(+)
> create mode 100644 arch/arm/boot/dts/imx6q-apalis-ixora.dts
>
> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> index 44508dc..29b1aae 100644
> --- a/arch/arm/boot/dts/Makefile
> +++ b/arch/arm/boot/dts/Makefile
> @@ -315,6 +315,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
> imx6dl-udoo.dtb \
> imx6dl-wandboard.dtb \
> imx6dl-wandboard-revb1.dtb \
> + imx6q-apalis-ixora.dtb \
> imx6q-apf6dev.dtb \
> imx6q-arm2.dtb \
> imx6q-cm-fx6.dtb \
> diff --git a/arch/arm/boot/dts/imx6q-apalis-ixora.dts
> b/arch/arm/boot/dts/imx6q-apalis-ixora.dts
> new file mode 100644
> index 0000000..5494a13
> --- /dev/null
> +++ b/arch/arm/boot/dts/imx6q-apalis-ixora.dts
> @@ -0,0 +1,256 @@
> +/*
> + * Copyright 2014-2016 Toradex AG
> + * Copyright 2012 Freescale Semiconductor, Inc.
> + * Copyright 2011 Linaro Ltd.
> + *
> + * This file is dual-licensed: you can use it either under the terms
> + * of the GPL or the X11 license, at your option. Note that this dual
> + * licensing only applies to this file, and not this project as a
> + * whole.
> + *
> + * a) This file is free software; you can redistribute it and/or
> + * modify it under the terms of the GNU General Public License
> + * version 2 as published by the Free Software Foundation.
> + *
> + * This file is distributed in the hope that it will be useful
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + *
> + * Or, alternatively
> + *
> + * b) Permission is hereby granted, free of charge, to any person
> + * obtaining a copy of this software and associated documentation
> + * files (the "Software"), to deal in the Software without
> + * restriction, including without limitation the rights to use
> + * copy, modify, merge, publish, distribute, sublicense, and/or
> + * sell copies of the Software, and to permit persons to whom the
> + * Software is furnished to do so, subject to the following
> + * conditions:
> + *
> + * The above copyright notice and this permission notice shall be
> + * included in all copies or substantial portions of the Software.
> + *
> + * THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND
> + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
> + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
> + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
> + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY
> + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
> + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
> + * OTHER DEALINGS IN THE SOFTWARE.
> + */
> +
> +/dts-v1/;
> +
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/input/input.h>
> +#include <dt-bindings/interrupt-controller/irq.h>
> +#include "imx6q.dtsi"
> +#include "imx6qdl-apalis.dtsi"
> +
> +/ {
> + model = "Toradex Apalis iMX6Q/D Module on Ixora Carrier Board";
> + compatible = "toradex,apalis_imx6q-ixora", "toradex,apalis_imx6q",
> + "fsl,imx6q";
> +
> + aliases {
> + i2c0 = &i2cddc;
> + i2c1 = &i2c1;
> + i2c2 = &i2c2;
> + i2c3 = &i2c3;
> + };
> +
> + aliases {
> + rtc0 = &rtc_i2c;
> + rtc1 = "/soc/aips-bus at 02000000/snvs at 020cc000/snvs-rtc-lp at 34";
Probably easier and better readable when using the label here
("&snvs_rtc").
> + };
> +
> + gpio-keys {
> + compatible = "gpio-keys";
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_gpio_keys>;
> +
> + wakeup {
> + label = "Wake-Up";
> + gpios = <&gpio1 4 GPIO_ACTIVE_LOW>;
> + linux,code = <KEY_WAKEUP>;
> + debounce-interval = <10>;
> + gpio-key,wakeup;
> + };
> + };
> +
> + leds {
> + compatible = "gpio-leds";
> +
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_leds_ixora>;
> +
> + led4-green {
> + label = "LED_4_GREEN";
> + gpios = <&gpio1 17 GPIO_ACTIVE_HIGH>;
> + };
> +
> + led4-red {
> + label = "LED_4_RED";
> + gpios = <&gpio1 21 GPIO_ACTIVE_HIGH>;
> + };
> +
> + led5-green {
> + label = "LED_5_GREEN";
> + gpios = <&gpio2 1 GPIO_ACTIVE_HIGH>;
> + };
> +
> + led5-red {
> + label = "LED_5_RED";
> + gpios = <&gpio2 2 GPIO_ACTIVE_HIGH>;
> + };
> + };
> +
> + pwmleds {
> + compatible = "pwm-leds";
> + ledpwm1 {
> + label = "PWM1";
> + pwms = <&pwm1 0 50000>;
> + max-brightness = <255>;
> + };
> +
> + ledpwm2 {
> + label = "PWM2";
> + pwms = <&pwm2 0 50000>;
> + max-brightness = <255>;
> + };
> +
> + ledpwm3 {
> + label = "PWM3";
> + pwms = <&pwm3 0 50000>;
> + max-brightness = <255>;
> + };
> + };
> +
> + regulators {
> + reg_usb_otg_vbus: usb_otg_vbus {
> + status = "okay";
> + };
> +
> + reg_usb_host_vbus: usb_host_vbus {
> + status = "okay";
> + };
> + };
> +};
> +
> +&backlight {
> + brightness-levels = <0 127 191 223 239 247 251 255>;
> + default-brightness-level = <1>;
> + status = "okay";
> +};
> +
> +&can1 {
> + status = "okay";
> +};
> +
> +&can2 {
> + status = "okay";
> +};
> +
> +/* GEN1_I2C: I2C1_SDA/SCL on MXM3 209/211 (e.g. RTC on carrier board) */
> +&i2c1 {
> + status = "okay";
> +
> + cat24c02 at 50 {
According to devicetree.org, nodes are named according to what kind of
device it represents. Hence this should be eeprom at 50.
> + compatible = "atmel,24c02";
> + reg = <0x50>;
> + };
> +
> + /* M41T0M6 real time clock on carrier board */
> + rtc_i2c: rtc at 68 {
> + compatible = "st,m41t00";
> + reg = <0x68>;
> + };
> +};
> +
> +&iomuxc {
This should go to the end of the device tree.
Otherwise looks good to me:
Reviewed-by: Stefan Agner <stefan at agner.ch>
--
Stefan
> + /*
> + * Mux the Apalis GPIOs, GPIO7 used for PCIe reset,
> + * GPIO5, 6 used by optional fusion_F0710A kernel module
> + */
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_apalis_gpio1 &pinctrl_apalis_gpio2
> + &pinctrl_apalis_gpio3 &pinctrl_apalis_gpio4
> + &pinctrl_apalis_gpio5 &pinctrl_apalis_gpio6
> + &pinctrl_apalis_gpio7 &pinctrl_apalis_gpio8>;
> +
> + leds_ixora {
> + pinctrl_leds_ixora: leds-ixora {
> + fsl,pins = <
> + MX6QDL_PAD_SD1_DAT1__GPIO1_IO17 PAD_CTRL_HYS_PU
> + MX6QDL_PAD_SD1_DAT3__GPIO1_IO21 PAD_CTRL_HYS_PU
> + MX6QDL_PAD_NANDF_D1__GPIO2_IO01 PAD_CTRL_HYS_PU
> + MX6QDL_PAD_NANDF_D2__GPIO2_IO02 PAD_CTRL_HYS_PU
> + >;
> + };
> + };
> +};
> +
> +&pcie {
> + /* active-low meaning opposite of regular PERST# active-low polarity */
> + reset-gpio = <&gpio1 28 GPIO_ACTIVE_LOW>;
> + status = "okay";
> +};
> +
> +&pwm1 {
> + status = "okay";
> +};
> +
> +&pwm2 {
> + status = "okay";
> +};
> +
> +&pwm3 {
> + status = "okay";
> +};
> +
> +&pwm4 {
> + status = "okay";
> +};
> +
> +&sata {
> + status = "okay";
> +};
> +
> +&sound_spdif {
> + status = "okay";
> +};
> +
> +&spdif {
> + status = "okay";
> +};
> +
> +&uart1 {
> + status = "okay";
> +};
> +
> +&uart2 {
> + status = "okay";
> +};
> +
> +&uart4 {
> + status = "okay";
> +};
> +
> +&uart5 {
> + status = "okay";
> +};
> +
> +&usbh1 {
> + status = "okay";
> +};
> +
> +&usbotg {
> + status = "okay";
> +};
> +
> +/* SD1 */
> +&usdhc2 {
> + status = "okay";
> +};
More information about the linux-arm-kernel
mailing list