serial: clk: bcm2835: Strange effects when using aux-uart in console
Martin Sperl
martin at sperl.org
Thu Feb 11 05:15:10 PST 2016
On 10.02.2016 16:12, Martin Sperl wrote:
> Hi!
>
> I got a strange effect when using the auxiliar UART as the logging console:
>
> The kernel is configured for drivers/tty/serial/8250/8250_bcm2835aux.c to
> get linked into the main kernel (requires also 8250.c to be linked in).
>
> As long as I boot using the main UART (PL011) in the kernel parameters:
> earlyprintk consoleblank=0 console=ttyAMA0 root=/dev/mmcblk0p2 rootwait
>
> Everything works fine - early_printk works and normal logging works as well.
> Both configured ttys (/dev/ttyAMA0 and /dev/ttyS0) in /etc/initttab
> work fine.
>
> Now when I switch the console to use the auxiliar UART
> (which right now does not support early_printk) like this:
> earlyprintk consoleblank=0 console=ttyS0,115200n1 root=/dev/mmcblk0p2 rootwait
>
> I get the situation where:
> * u-boot starts and writes to the main UART
> * Kernel boots using early_printk logging to the main UART until we get to:
> [ 2.657090] bootconsole [earlycon0] disabled
> * then we see the earlyprintk buffer dumped on the aux-uart
> * then booting continues and logging happens on the aux-uart:
> [ 2.657090] bootconsole [earlycon0] disabled
> [ 2.662673] 20201000.serial: ttyAMA0 at MMIO 0x20201000 (irq = 81, base_baud = 0) is a PL011 rev2
> [ 2.663793] console [ttyS0] disabled
> [ 2.663899] 20215040.serial: ttyS0 at MMIO 0x0 (irq = 53, base_baud = 31224999) is a 16550
> [ 3.384166] console [ttyS0] enabled
> * everything works fine and I get networking and everything up
> [....] Starting NTP server: ntpd. ok
> [....] Starting OpenBSD Secure Shell server: sshd. ok
> My IP address is 10.10.10.41 ::127.0.0.1
>
> Raspbian GNU/Linux 7 raspcm.intern.sperl.org ttyS0
> * I can even log in via SSH and networking works.
> Note that I have the getty for ttyAMA0 disabled in inittab
> * when I then enable the tty on the main UART like this:
> root at raspcm:~# /sbin/getty -a root -L ttyAMA0 115200 vt100
> * I get the following:
> [ 72.962845] uart-pl011 20201000.serial: no DMA platform data
> * the system freezes…
> * sometimes I still get the following on the auxiliar UART before the system “crashes":
> (at least when starting the tty from inittab)
> [ 73.072985] bcm2835-clk 20101000.cprman: plld: couldn't lock PLL
> [ 73.079132] ------------[ cut here ]------------
> [ 73.083848] WARNING: CPU: 0 PID: 2329 at drivers/clk/clk.c:680 clk_core_disable+0x34/0xf0()
> [ 73.093067] ---[ end trace 416e78cea88f5fb5 ]---
> [ 73.097848] ------------[ cut here ]------------
> [ 73.102616] WARNING: CPU: 0 PID: 2329 at drivers/clk/clk.c:575 clk_core_unprepare+0x34/0x110()
> [ 73.112219] ---[ end trace 416e78cea88f5fb6 ]---
>
> A similar effect I get when using stty:
> root at raspcm:~# stty -F /dev/ttyAMA0
> [ 128.878127] uart-pl011 20201000.serial: no DMA platform data
> speed 9600 baud; line = 0;
> -brkint -imaxbel
> Then the system freezes.
>
> As if the plld does not lock - even if it (probably) is already locked.
>
> Or the message actually comes from bcm2835_clock_wait_busy which also
> produces this message - so maybe we should better identify the message.
>
> Note that the same also applies if I remove earlyprintk with
> the only difference being that I do not get the initial boot
> messages on the main UART.
> (at that time only: "Uncompressing Linux... done, booting the kernel.”
> shows on the main uart after u-boot start..)
>
> Unfortunately it is only possible to really test this on a
> rpi-Compute module, as only there we can expose both uarts
> on distinct GPIOs at the same time:
> GPIO 14: level=1 fsel=4 alt=0 func=TXD0
> GPIO 15: level=1 fsel=4 alt=0 func=RXD0
> GPIO 32: level=1 fsel=2 alt=5 func=TXD1
> GPIO 33: level=1 fsel=2 alt=5 func=RXD1
>
> Here the commits I have used based on spi/for-next (based on 4.4.0)
> with the patches (* prefix) for the driver for aux-uart
> added separately as they are not in the tree I have used:
> * a96f6c7 serial: bcm2835: add driver for bcm2835-aux-uart
> * 464e876 clk: bcm2835: Add bindings for the auxiliary peripheral clock gates.
> * 1af1b28 clk: bcm2835: Add a driver for the auxiliary peripheral clock gates.
> ece19b8 Merge remote-tracking branch 'spi/fix/loopback' into spi-linus
> 887e6a3 Merge tag 'spi-v4.5' into spi-linus
> ebea7c0 spi: fix counting in spi-loopback-test code
> cabeea9 Merge remote-tracking branches 'spi/topic/sun4i', 'spi/topic/topcliff-pc
> 4f95307 Merge remote-tracking branches 'spi/topic/overlay', 'spi/topic/pxa2xx',
> 41d5a70 Merge remote-tracking branches 'spi/topic/lm70llp', 'spi/topic/loopback'
> 635b9b2 Merge remote-tracking branches 'spi/topic/dw', 'spi/topic/dw-mid', 'spi/
> 3c27892 Merge remote-tracking branches 'spi/topic/bcm63xx', 'spi/topic/butterfly
> 9b17e80 Merge remote-tracking branch 'spi/topic/sunxi' into spi-next
> 174c211 Merge remote-tracking branch 'spi/topic/core' into spi-next
> f30f072 Merge remote-tracking branch 'spi/fix/mtk' into spi-linus
> afd2ff9 Linux 4.4
>
> Maybe someone has gotten any idea?
>
> In the meantime I will try to reproduce on a 4.5-rc3 based branch.
Same issue with 4.5-rc3 - here the commits:
* bec2300c serial: bcm2835: add driver for bcm2835-aux-uart
388f7b1 Linux 4.5-rc3
Here the clock calls I have instrumented for the console=ttyAMA0 case:
[ 1.884107] bcm2835-clk 20101000.cprman: bcm2835_pll_get_rate - plla
[ 1.890723] bcm2835-clk 20101000.cprman: bcm2835_pll_get_rate - pllb
[ 1.897308] bcm2835-clk 20101000.cprman: bcm2835_pll_get_rate - pllc
[ 1.903849] bcm2835-clk 20101000.cprman: bcm2835_pll_get_rate - plld
[ 1.910429] bcm2835-clk 20101000.cprman: bcm2835_pll_get_rate - pllh
[ 1.917184] bcm2835-clk 20101000.cprman: bcm2835_clock_get_parent - timer
[ 1.924143] bcm2835-clk 20101000.cprman: bcm2835_clock_get_rate - timer
[ 1.931237] bcm2835-clk 20101000.cprman: bcm2835_clock_get_parent - otp
[ 1.938081] bcm2835-clk 20101000.cprman: bcm2835_clock_get_rate - otp
[ 1.944757] bcm2835-clk 20101000.cprman: bcm2835_clock_get_parent - tsens
[ 1.951714] bcm2835-clk 20101000.cprman: bcm2835_clock_get_rate - tsens
[ 1.958605] bcm2835-clk 20101000.cprman: bcm2835_clock_get_parent - vpu
[ 1.965429] bcm2835-clk 20101000.cprman: bcm2835_clock_get_rate - vpu
[ 1.972088] bcm2835-clk 20101000.cprman: bcm2835_clock_get_parent - v3d
[ 1.978909] bcm2835-clk 20101000.cprman: bcm2835_clock_get_rate - v3d
[ 1.985622] bcm2835-clk 20101000.cprman: bcm2835_clock_get_parent - isp
[ 1.992405] bcm2835-clk 20101000.cprman: bcm2835_clock_get_rate - isp
[ 1.999101] bcm2835-clk 20101000.cprman: bcm2835_clock_get_parent - h264
[ 2.006011] bcm2835-clk 20101000.cprman: bcm2835_clock_get_rate - h264
[ 2.012774] bcm2835-clk 20101000.cprman: bcm2835_clock_get_parent - sdram
[ 2.019772] bcm2835-clk 20101000.cprman: bcm2835_clock_get_rate - sdram
[ 2.026848] bcm2835-clk 20101000.cprman: bcm2835_clock_get_parent - uart
[ 2.033725] bcm2835-clk 20101000.cprman: bcm2835_clock_get_rate - uart
[ 2.040521] bcm2835-clk 20101000.cprman: bcm2835_clock_get_parent - vec
[ 2.047366] bcm2835-clk 20101000.cprman: bcm2835_clock_get_rate - vec
[ 2.054207] bcm2835-clk 20101000.cprman: bcm2835_clock_get_parent - hsm
[ 2.061065] bcm2835-clk 20101000.cprman: bcm2835_clock_get_rate - hsm
[ 2.067720] bcm2835-clk 20101000.cprman: bcm2835_clock_get_parent - hsm
[ 2.074699] bcm2835-clk 20101000.cprman: bcm2835_clock_get_parent - emmc
[ 2.081574] bcm2835-clk 20101000.cprman: bcm2835_clock_get_rate - emmc
[ 2.088316] bcm2835-clk 20101000.cprman: bcm2835_clock_get_parent - hsm
[ 2.095253] bcm2835-clk 20101000.cprman: bcm2835_clock_get_parent - hsm
[ 2.102112] bcm2835-clk 20101000.cprman: bcm2835_clock_get_parent - pwm
[ 2.108951] bcm2835-clk 20101000.cprman: bcm2835_clock_get_rate - pwm
[ 2.115594] bcm2835-clk 20101000.cprman: bcm2835_clock_get_parent - pwm
[ 2.122374] bcm2835-clk 20101000.cprman: bcm2835_clock_get_parent - hsm
[ 2.129667] bcm2835-clk 20101000.cprman: bcm2835_clock_get_parent - pwm
[ 2.136523] bcm2835-clk 20101000.cprman: bcm2835_clock_get_parent - hsm
[ 2.143329] bcm2835-clk 20101000.cprman: bcm2835_clock_get_parent - pwm
[ 2.150148] bcm2835-clk 20101000.cprman: bcm2835_clock_get_parent - hsm
[ 2.157157] bcm2835-clk 20101000.cprman: bcm2835_clock_get_parent - pwm
[ 2.163942] bcm2835-clk 20101000.cprman: bcm2835_clock_get_parent - hsm
[ 2.230330] bcm2835-clk 20101000.cprman: bcm2835_pll_on - pllc
[ 2.245552] bcm2835-clk 20101000.cprman: bcm2835_pll_on - plld
[ 2.251559] bcm2835-clk 20101000.cprman: bcm2835_clock_on - uart
[ 2.284246] bcm2835-clk 20101000.cprman: bcm2835_clock_on - emmc
And for the console=ttyS0,115200 case:
[ 1.884106] bcm2835-clk 20101000.cprman: bcm2835_pll_get_rate - plla
[ 1.890721] bcm2835-clk 20101000.cprman: bcm2835_pll_get_rate - pllb
[ 1.897307] bcm2835-clk 20101000.cprman: bcm2835_pll_get_rate - pllc
[ 1.903849] bcm2835-clk 20101000.cprman: bcm2835_pll_get_rate - plld
[ 1.910429] bcm2835-clk 20101000.cprman: bcm2835_pll_get_rate - pllh
[ 1.917183] bcm2835-clk 20101000.cprman: bcm2835_clock_get_parent - timer
[ 1.924143] bcm2835-clk 20101000.cprman: bcm2835_clock_get_rate - timer
[ 1.931234] bcm2835-clk 20101000.cprman: bcm2835_clock_get_parent - otp
[ 1.938077] bcm2835-clk 20101000.cprman: bcm2835_clock_get_rate - otp
[ 1.944759] bcm2835-clk 20101000.cprman: bcm2835_clock_get_parent - tsens
[ 1.951717] bcm2835-clk 20101000.cprman: bcm2835_clock_get_rate - tsens
[ 1.958607] bcm2835-clk 20101000.cprman: bcm2835_clock_get_parent - vpu
[ 1.965429] bcm2835-clk 20101000.cprman: bcm2835_clock_get_rate - vpu
[ 1.972089] bcm2835-clk 20101000.cprman: bcm2835_clock_get_parent - v3d
[ 1.978908] bcm2835-clk 20101000.cprman: bcm2835_clock_get_rate - v3d
[ 1.985620] bcm2835-clk 20101000.cprman: bcm2835_clock_get_parent - isp
[ 1.992406] bcm2835-clk 20101000.cprman: bcm2835_clock_get_rate - isp
[ 1.999102] bcm2835-clk 20101000.cprman: bcm2835_clock_get_parent - h264
[ 2.006010] bcm2835-clk 20101000.cprman: bcm2835_clock_get_rate - h264
[ 2.012772] bcm2835-clk 20101000.cprman: bcm2835_clock_get_parent - sdram
[ 2.019769] bcm2835-clk 20101000.cprman: bcm2835_clock_get_rate - sdram
[ 2.026842] bcm2835-clk 20101000.cprman: bcm2835_clock_get_parent - uart
[ 2.033719] bcm2835-clk 20101000.cprman: bcm2835_clock_get_rate - uart
[ 2.040518] bcm2835-clk 20101000.cprman: bcm2835_clock_get_parent - vec
[ 2.047362] bcm2835-clk 20101000.cprman: bcm2835_clock_get_rate - vec
[ 2.054199] bcm2835-clk 20101000.cprman: bcm2835_clock_get_parent - hsm
[ 2.061052] bcm2835-clk 20101000.cprman: bcm2835_clock_get_rate - hsm
[ 2.067706] bcm2835-clk 20101000.cprman: bcm2835_clock_get_parent - hsm
[ 2.074688] bcm2835-clk 20101000.cprman: bcm2835_clock_get_parent - emmc
[ 2.081561] bcm2835-clk 20101000.cprman: bcm2835_clock_get_rate - emmc
[ 2.088303] bcm2835-clk 20101000.cprman: bcm2835_clock_get_parent - hsm
[ 2.095241] bcm2835-clk 20101000.cprman: bcm2835_clock_get_parent - hsm
[ 2.102100] bcm2835-clk 20101000.cprman: bcm2835_clock_get_parent - pwm
[ 2.108938] bcm2835-clk 20101000.cprman: bcm2835_clock_get_rate - pwm
[ 2.115582] bcm2835-clk 20101000.cprman: bcm2835_clock_get_parent - pwm
[ 2.122362] bcm2835-clk 20101000.cprman: bcm2835_clock_get_parent - hsm
[ 2.129648] bcm2835-clk 20101000.cprman: bcm2835_clock_get_parent - pwm
[ 2.136509] bcm2835-clk 20101000.cprman: bcm2835_clock_get_parent - hsm
[ 2.143315] bcm2835-clk 20101000.cprman: bcm2835_clock_get_parent - pwm
[ 2.150135] bcm2835-clk 20101000.cprman: bcm2835_clock_get_parent - hsm
[ 2.157145] bcm2835-clk 20101000.cprman: bcm2835_clock_get_parent - pwm
[ 2.163929] bcm2835-clk 20101000.cprman: bcm2835_clock_get_parent - hsm
[ 2.230333] bcm2835-clk 20101000.cprman: bcm2835_pll_on - pllc
[ 2.275803] bcm2835-clk 20101000.cprman: bcm2835_clock_on - emmc
The only real difference is this diff:
@@ -41,6 +41,4 @@
20101000.cprman: bcm2835_clock_get_parent - pwm
20101000.cprman: bcm2835_clock_get_parent - hsm
20101000.cprman: bcm2835_pll_on - pllc
- 20101000.cprman: bcm2835_pll_on - plld
- 20101000.cprman: bcm2835_clock_on - uart
20101000.cprman: bcm2835_clock_on - emmc
so plld and uart are not started for the console=ttyS0 case.
After I instrumented clk-bcm2835.c to see what happens in the driver
and running: /sbin/getty -a root -L ttyAMA0 115200 vt100
I get the following:
[ 146.342341] bcm2835-clk 20101000.cprman: bcm2835_pll_on - plld
[ 146.348426] bcm2835-clk 20101000.cprman: bcm2835_clock_on - uart
[ 146.354639] uart-pl011 20201000.uart: no DMA platform data
[ 146.375535] bcm2835-clk 20101000.cprman: bcm2835_clock_off - uart
[ 146.381776] bcm2835-clk 20101000.cprman: bcm2835_clock_wait_busy - uart
[ 146.388595] bcm2835-clk 20101000.cprman: bcm2835_pll_off - plld
[ 146.396574] bcm2835-clk 20101000.cprman: bcm2835_pll_on - plld
[ 146.502551] bcm2835-clk 20101000.cprman: plld: couldn't lock PLL
[ 146.508726] ------------[ cut here ]------------
[ 146.513448] WARNING: CPU: 0 PID: 2349 at drivers/clk/clk.c:680
clk_core_disa)
[ 146.522673] ---[ end trace 33268753126338e9 ]---
[ 146.527478] ------------[ cut here ]------------
[ 146.532224] WARNING: CPU: 0 PID: 2349 at drivers/clk/clk.c:575
clk_core_unpr)
[ 146.541866] ---[ end trace 33268753126338ea ]---
So I wonder why we would disable and reenable the plld and uart clock
Note that just adding a return in bcm2835_pll_off like this:
@@ -900,6 +905,9 @@ static void bcm2835_pll_off(struct clk_hw *hw)
struct bcm2835_cprman *cprman = pll->cprman;
const struct bcm2835_pll_data *data = pll->data;
+ dev_err(cprman->dev, "%s - %s\n", __FUNCTION__, clk_hw_get_name(hw));
+ return;
+
cprman_write(cprman, data->cm_ctrl_reg, CM_PLL_ANARST);
cprman_write(cprman, data->a2w_ctrl_reg, A2W_PLL_CTRL_PWRDN);
}
avoids the crash, but the tty is non-functional.
Calling sequence of the clock driver is:
[ 145.022546] bcm2835-clk 20101000.cprman: bcm2835_pll_on - plld
[ 145.028619] bcm2835-clk 20101000.cprman: bcm2835_clock_on - uart
[ 145.034807] uart-pl011 20201000.uart: no DMA platform data
[ 145.045089] bcm2835-clk 20101000.cprman: bcm2835_clock_off - uart
[ 145.051418] bcm2835-clk 20101000.cprman: bcm2835_clock_wait_busy - uart
[ 145.058215] bcm2835-clk 20101000.cprman: bcm2835_pll_off - plld
[ 145.065779] bcm2835-clk 20101000.cprman: bcm2835_pll_on - plld
[ 145.071761] bcm2835-clk 20101000.cprman: bcm2835_clock_on - uart
debugfs shows the following after the above:
root at raspcm:~# head /sys/kernel/debug/clk/uart*/clk_rate
==> /sys/kernel/debug/clk/uart0_pclk/clk_rate <==
3000000
==> /sys/kernel/debug/clk/uart1_pclk/clk_rate <==
125000000
==> /sys/kernel/debug/clk/uart/clk_rate <==
2997598
Is this maybe related to the uart0_pclk, uart1_pclk, apb_pclk
clocks created and registered in bcm2835_init_clocks?
Any Ideas?
Thanks,
Martin
More information about the linux-arm-kernel
mailing list