serial: clk: bcm2835: Strange effects when using aux-uart in console
stefan.wahren at i2se.com
Wed Feb 10 09:21:31 PST 2016
Am 10.02.2016 um 16:12 schrieb Martin Sperl:
> I got a strange effect when using the auxiliar UART as the logging console:
> The kernel is configured for drivers/tty/serial/8250/8250_bcm2835aux.c to
> get linked into the main kernel (requires also 8250.c to be linked in).
> As long as I boot using the main UART (PL011) in the kernel parameters:
> earlyprintk consoleblank=0 console=ttyAMA0 root=/dev/mmcblk0p2 rootwait
> Everything works fine - early_printk works and normal logging works as well.
> Both configured ttys (/dev/ttyAMA0 and /dev/ttyS0) in /etc/initttab
> work fine.
> Now when I switch the console to use the auxiliar UART
> (which right now does not support early_printk) like this:
> earlyprintk consoleblank=0 console=ttyS0,115200n1 root=/dev/mmcblk0p2 rootwait
> I get the situation where:
> * u-boot starts and writes to the main UART
> * Kernel boots using early_printk logging to the main UART until we get to:
> [ 2.657090] bootconsole [earlycon0] disabled
> * then we see the earlyprintk buffer dumped on the aux-uart
> * then booting continues and logging happens on the aux-uart:
> [ 2.657090] bootconsole [earlycon0] disabled
> [ 2.662673] 20201000.serial: ttyAMA0 at MMIO 0x20201000 (irq = 81, base_baud = 0) is a PL011 rev2
> [ 2.663793] console [ttyS0] disabled
> [ 2.663899] 20215040.serial: ttyS0 at MMIO 0x0 (irq = 53, base_baud = 31224999) is a 16550
> [ 3.384166] console [ttyS0] enabled
> * everything works fine and I get networking and everything up
> [....] Starting NTP server: ntpd. ok
> [....] Starting OpenBSD Secure Shell server: sshd. ok
> My IP address is 10.10.10.41 ::127.0.0.1
> Raspbian GNU/Linux 7 raspcm.intern.sperl.org ttyS0
> * I can even log in via SSH and networking works.
> Note that I have the getty for ttyAMA0 disabled in inittab
> * when I then enable the tty on the main UART like this:
> root at raspcm:~# /sbin/getty -a root -L ttyAMA0 115200 vt100
> * I get the following:
> [ 72.962845] uart-pl011 20201000.serial: no DMA platform data
> * the system freezes…
> * sometimes I still get the following on the auxiliar UART before the system “crashes":
> (at least when starting the tty from inittab)
> [ 73.072985] bcm2835-clk 20101000.cprman: plld: couldn't lock PLL
> [ 73.079132] ------------[ cut here ]------------
> [ 73.083848] WARNING: CPU: 0 PID: 2329 at drivers/clk/clk.c:680 clk_core_disable+0x34/0xf0()
> [ 73.093067] ---[ end trace 416e78cea88f5fb5 ]---
> [ 73.097848] ------------[ cut here ]------------
> [ 73.102616] WARNING: CPU: 0 PID: 2329 at drivers/clk/clk.c:575 clk_core_unprepare+0x34/0x110()
> [ 73.112219] ---[ end trace 416e78cea88f5fb6 ]---
> A similar effect I get when using stty:
> root at raspcm:~# stty -F /dev/ttyAMA0
> [ 128.878127] uart-pl011 20201000.serial: no DMA platform data
> speed 9600 baud; line = 0;
> -brkint -imaxbel
> Then the system freezes.
> As if the plld does not lock - even if it (probably) is already locked.
> Or the message actually comes from bcm2835_clock_wait_busy which also
> produces this message - so maybe we should better identify the message.
> Note that the same also applies if I remove earlyprintk with
> the only difference being that I do not get the initial boot
> messages on the main UART.
> (at that time only: "Uncompressing Linux... done, booting the kernel.”
> shows on the main uart after u-boot start..)
> Unfortunately it is only possible to really test this on a
> rpi-Compute module, as only there we can expose both uarts
> on distinct GPIOs at the same time:
> GPIO 14: level=1 fsel=4 alt=0 func=TXD0
> GPIO 15: level=1 fsel=4 alt=0 func=RXD0
> GPIO 32: level=1 fsel=2 alt=5 func=TXD1
> GPIO 33: level=1 fsel=2 alt=5 func=RXD1
> Here the commits I have used based on spi/for-next (based on 4.4.0)
> with the patches (* prefix) for the driver for aux-uart
> added separately as they are not in the tree I have used:
> * a96f6c7 serial: bcm2835: add driver for bcm2835-aux-uart
> * 464e876 clk: bcm2835: Add bindings for the auxiliary peripheral clock gates.
> * 1af1b28 clk: bcm2835: Add a driver for the auxiliary peripheral clock gates.
> ece19b8 Merge remote-tracking branch 'spi/fix/loopback' into spi-linus
> 887e6a3 Merge tag 'spi-v4.5' into spi-linus
> ebea7c0 spi: fix counting in spi-loopback-test code
> cabeea9 Merge remote-tracking branches 'spi/topic/sun4i', 'spi/topic/topcliff-pc
> 4f95307 Merge remote-tracking branches 'spi/topic/overlay', 'spi/topic/pxa2xx',
> 41d5a70 Merge remote-tracking branches 'spi/topic/lm70llp', 'spi/topic/loopback'
> 635b9b2 Merge remote-tracking branches 'spi/topic/dw', 'spi/topic/dw-mid', 'spi/
> 3c27892 Merge remote-tracking branches 'spi/topic/bcm63xx', 'spi/topic/butterfly
> 9b17e80 Merge remote-tracking branch 'spi/topic/sunxi' into spi-next
> 174c211 Merge remote-tracking branch 'spi/topic/core' into spi-next
> f30f072 Merge remote-tracking branch 'spi/fix/mtk' into spi-linus
> afd2ff9 Linux 4.4
> Maybe someone has gotten any idea?
this sounds like an issue i had with the compute module here:
Unfortunately i don't have the cm anymore.
Maybe you can try this downstream patch:
More information about the linux-arm-kernel