[PATCH v4 2/5] ARM: dts: Prepare exynos5410-odroidxu device tree

[Javier Martinez Canillas]

Hello Andreas,

On Sun, Mar 15, 2015 at 11:00 PM, Andreas Färber <afaerber at suse.de> wrote:
> Derived from exynos5410-smdk5410.dts.
>
> Signed-off-by: Andreas Färber <afaerber at suse.de>
> ---
>  v1 -> v2 -> v3: Unchanged
>
>  arch/arm/boot/dts/Makefile                |  1 +
>  arch/arm/boot/dts/exynos5410-odroidxu.dts | 78 +++++++++++++++++++++++++++++++
>  2 files changed, 79 insertions(+)
>  create mode 100644 arch/arm/boot/dts/exynos5410-odroidxu.dts
>
> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> index a1c776b8dcec..b040737edcbc 100644
> --- a/arch/arm/boot/dts/Makefile
> +++ b/arch/arm/boot/dts/Makefile
> @@ -103,6 +103,7 @@ dtb-$(CONFIG_ARCH_EXYNOS5) += \
>         exynos5250-snow.dtb \
>         exynos5250-spring.dtb \
>         exynos5260-xyref5260.dtb \
> +       exynos5410-odroidxu.dtb \
>         exynos5410-smdk5410.dtb \
>         exynos5420-arndale-octa.dtb \
>         exynos5420-peach-pit.dtb \
> diff --git a/arch/arm/boot/dts/exynos5410-odroidxu.dts b/arch/arm/boot/dts/exynos5410-odroidxu.dts
> new file mode 100644
> index 000000000000..97310bb727e2
> --- /dev/null
> +++ b/arch/arm/boot/dts/exynos5410-odroidxu.dts
> @@ -0,0 +1,78 @@
> +/*
> + * Hardkernel ODROID-XU device tree source
> + *
> + * Copyright (c) 2014 SUSE LINUX Products GmbH
> + *
> + * Based on exynos5410-smdk5410.dts:
> + *
> + * Copyright (c) 2013 Samsung Electronics Co., Ltd.
> + *             http://www.samsung.com
> + *
> + * This program is free software; you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License version 2 as
> + * published by the Free Software Foundation.
> +*/
> +
> +/dts-v1/;
> +#include "exynos5410.dtsi"
> +/ {
> +       model = "ODROID-XU based on EXYNOS5410";
> +       compatible = "hardkernel,odroid-xu", "samsung,exynos5410", "samsung,exynos5";
> +
> +       memory {
> +               reg = <0x40000000 0x80000000>;
> +       };
> +
> +       chosen {
> +               bootargs = "console=ttySAC2,115200";
> +       };
> +

After commit a208ffd251d0 ("of: Enable console on serial ports
specified by /chosen/stdout-path") the kernel is able to know what
serial console to use if the DT defined an stdout-path property so
should be preferred instead of using a console= parameter.

I'll post today a series to change that on all exynos5 boards so you
can base on that.

> +       fin_pll: xxti {
> +               compatible = "fixed-clock";
> +               clock-frequency = <24000000>;
> +               clock-output-names = "fin_pll";
> +               #clock-cells = <0>;
> +       };
> +

I think this should be defined in exynos5410.dtsi instead since is an
IP block in the SoC and referenced in the .dts using a label to change
the clock-frequency in the board.

> +       firmware at 02037000 {
> +               compatible = "samsung,secure-firmware";
> +               reg = <0x02037000 0x1000>;
> +       };
> +
> +};
> +
> +&mmc_0 {
> +       status = "okay";
> +       num-slots = <1>;
> +       cap-mmc-highspeed;
> +       broken-cd;
> +       card-detect-delay = <200>;
> +       samsung,dw-mshc-ciu-div = <3>;
> +       samsung,dw-mshc-sdr-timing = <2 3>;
> +       samsung,dw-mshc-ddr-timing = <1 2>;
> +       bus-width = <8>;
> +};
> +
> +&mmc_2 {
> +       status = "okay";
> +       num-slots = <1>;
> +       cap-sd-highspeed;
> +       card-detect-delay = <200>;
> +       samsung,dw-mshc-ciu-div = <3>;
> +       samsung,dw-mshc-sdr-timing = <2 3>;
> +       samsung,dw-mshc-ddr-timing = <1 2>;
> +       bus-width = <4>;
> +       disable-wp;
> +};
> +
> +&uart0 {
> +       status = "okay";
> +};
> +
> +&uart1 {
> +       status = "okay";
> +};
> +
> +&uart2 {
> +       status = "okay";
> +};
> --

With those two changes:

Reviewed-by: Javier Martinez Canillas <javier.martinez at collabora.co.uk>

Best regards,
Javier