[PATCH 03/17] phy: ti-pipe3: use *syscon* framework to set PCS value of the PHY

[Roger Quadros]

On Wed, 24 Jun 2015 18:46:08 +0530
Kishon Vijay Abraham I <kishon at ti.com> wrote:

> Hi,
> 
> On Wednesday 24 June 2015 04:04 PM, Roger Quadros wrote:
> > On Tue, 23 Jun 2015 17:28:48 +0530
> > Kishon Vijay Abraham I <kishon at ti.com> wrote:
> > 
> >> Deprecate using phy-omap-control driver to set PCS value of the PHY
> >> and start using *syscon* framework to do the same.
> >>
> >> Signed-off-by: Kishon Vijay Abraham I <kishon at ti.com>
> >> ---
> >>   Documentation/devicetree/bindings/phy/ti-phy.txt |    2 ++
> >>   drivers/phy/phy-ti-pipe3.c                       |   32 +++++++++++++++++++++-
> >>   2 files changed, 33 insertions(+), 1 deletion(-)
> >>
> >> diff --git a/Documentation/devicetree/bindings/phy/ti-phy.txt b/Documentation/devicetree/bindings/phy/ti-phy.txt
> >> index d3ad3bf..52c7a92 100644
> >> --- a/Documentation/devicetree/bindings/phy/ti-phy.txt
> >> +++ b/Documentation/devicetree/bindings/phy/ti-phy.txt
> >> @@ -83,6 +83,8 @@ Optional properties:
> >>    - syscon-pllreset: Handle to system control region that contains the
> >>      CTRL_CORE_SMA_SW_0 register and register offset to the CTRL_CORE_SMA_SW_0
> >>      register that contains the SATA_PLL_SOFT_RESET bit. Only valid for sata_phy.
> >> + - syscon-pcs : phandle/offset pair. Phandle to the system control module and the
> >> +   register offset to write the PCS delay value.
> > 
> > What is PCS?
> 
> IIRC physical coding subsystem.
> > Is this valid only for PCIe? If yes we could mention it here.
> 
> This is introduced specifically for PCIe. But there are other PCS registers
> with a different register map altogether for USB. I'm not sure if we will ever
> have to do those settings.

OK then let's not say it is PCIe specific.

cheers,
-roger

> 
> > 
> >>   
> >>   Deprecated properties:
> >>    - ctrl-module : phandle of the control module used by PHY driver to power on
> >> diff --git a/drivers/phy/phy-ti-pipe3.c b/drivers/phy/phy-ti-pipe3.c
> >> index 78bac00..e2f9ad7 100644
> >> --- a/drivers/phy/phy-ti-pipe3.c
> >> +++ b/drivers/phy/phy-ti-pipe3.c
> >> @@ -65,6 +65,9 @@
> >>   #define PIPE3_PHY_TX_RX_POWERON		0x3
> >>   #define PIPE3_PHY_TX_RX_POWEROFF	0x0
> >>   
> >> +#define PCIE_PCS_MASK			0xFF0000
> >> +#define PCIE_PCS_DELAY_COUNT_SHIFT	0x10
> >> +
> >>   /*
> >>    * This is an Empirical value that works, need to confirm the actual
> >>    * value required for the PIPE3PHY_PLL_CONFIGURATION2.PLL_IDLE status
> >> @@ -96,9 +99,11 @@ struct ti_pipe3 {
> >>   	struct clk		*div_clk;
> >>   	struct pipe3_dpll_map	*dpll_map;
> >>   	struct regmap		*phy_power_syscon; /* ctrl. reg. acces */
> >> +	struct regmap		*pcs_syscon; /* ctrl. reg. acces */
> >>   	struct regmap		*dpll_reset_syscon; /* ctrl. reg. acces */
> >>   	unsigned int		dpll_reset_reg; /* reg. index within syscon */
> >>   	unsigned int		power_reg; /* power reg. index within syscon */
> >> +	unsigned int		pcie_pcs_reg; /* pcs reg. index in syscon */
> >>   	bool			sata_refclk_enabled;
> >>   };
> >>   
> >> @@ -271,7 +276,16 @@ static int ti_pipe3_init(struct phy *x)
> >>   	 * 18-1804.
> >>   	 */
> >>   	if (of_device_is_compatible(phy->dev->of_node, "ti,phy-pipe3-pcie")) {
> >> -		omap_control_pcie_pcs(phy->control_dev, 0x96);
> >> +		if (phy->pcs_syscon) {
> >> +			val = 0x96 << OMAP_CTRL_PCIE_PCS_DELAY_COUNT_SHIFT;
> >> +			ret = regmap_update_bits(phy->pcs_syscon,
> >> +						 phy->pcie_pcs_reg,
> >> +						 PCIE_PCS_MASK, val);
> >> +			if (ret < 0)
> >> +				return ret;
> >> +		} else {
> >> +			omap_control_pcie_pcs(phy->control_dev, 0x96);
> >> +		}
> >>   		return 0;
> >>   	}
> >>   
> >> @@ -455,6 +469,22 @@ static int ti_pipe3_probe(struct platform_device *pdev)
> >>   			dev_err(&pdev->dev, "unable to get div-clk\n");
> >>   			return PTR_ERR(phy->div_clk);
> >>   		}
> >> +
> >> +		phy->pcs_syscon = syscon_regmap_lookup_by_phandle(node,
> >> +								  "syscon-pcs");
> >> +		if (IS_ERR(phy->pcs_syscon)) {
> >> +			dev_dbg(&pdev->dev,
> >> +				 "can't get syscon-pcs, using omap control\n");
> >> +			phy->pcs_syscon = NULL;
> >> +		} else {
> >> +			if (of_property_read_u32_index(node,
> >> +						       "syscon-pcs", 1,
> >> +						       &phy->pcie_pcs_reg)) {
> >> +				dev_err(&pdev->dev,
> >> +					"couldn't get pcie pcs reg. offset\n");
> >> +				return -EINVAL;
> >> +			}
> >> +		}
> >>   	} else {
> >>   		phy->div_clk = ERR_PTR(-ENODEV);
> >>   	}
> >> -- 
> >> 1.7.9.5
> >>
> > 
> > Other than that,
> > 
> > Acked-by: Roger Quadros <rogerq at ti.com>
> > 
> > cheers,
> > -roger
> >