[ehci-orion] ETIMEOUT with ehci_setup()'s ehci_halt()
Valentin Longchamp
valentin.longchamp at keymile.com
Tue Jun 16 02:06:33 PDT 2015
On 06/12/2015 01:37 PM, Valentin Longchamp wrote:
> On 06/08/2015 01:46 PM, Valentin Longchamp wrote:
>> On 06/06/2015 02:17 PM, Sebastian Hesselbarth wrote:
>>> On 05.06.2015 17:19, Andrew Lunn wrote:
>>>> On Fri, Jun 05, 2015 at 04:34:54PM +0200, Valentin Longchamp wrote:
>>>>> I am currently bringing up the USB 2.0 Host controller of the Bobcat's (98DX4122
>>>>> Marvell switch) internal kirkwood CPU on a variation of Keymile's km_kirwood
>>>>> hardware (kirkwood-km_kirkwood.dts).
>>>>>
>>>>> When the driver registers its hcd, it fails with a timemout as it can be seen in
>>>>> the below log:
>>>>>
>>>>>> root at kmcoge5un:~# dmesg -n 8
>>>>>> root at kmcoge5un:~# insmod ehci-orion.ko
>>>>>> ehci-orion: EHCI orion driver
>>>>>> Initializing Orion-SoC USB Host Controller
>>>>>> orion-ehci f1050000.ehci: EHCI Host Controller
>>>>>> orion-ehci f1050000.ehci: new USB bus registered, assigned bus number 1
>>>>>> orion-ehci f1050000.ehci: reset hcs_params 0x10011 dbg=0 ind cc=0 pcc=0 ordered ports=1
>>>>>> orion-ehci f1050000.ehci: reset hcc_params 0006 thresh 0 uframes 256/512/1024 park
>>>>>> orion-ehci f1050000.ehci: park 0
>>>>>> orion-ehci f1050000.ehci: reset command 0080002 (park)=0 ithresh=8 period=1024 Reset HALT
>>>>>> orion-ehci f1050000.ehci: can't setup
>>>>>> orion-ehci f1050000.ehci: USB bus 1 deregistered
>>>>>> orion-ehci f1050000.ehci: init f1050000.ehci fail, -110
>>>>>> orion-ehci: probe of f1050000.ehci failed with error -110
>>>>>
>>>>> This is very similar to this problem, except that it always happens:
>>>>> https://lkml.org/lkml/2012/6/4/381
>>>>>
>>>>> I have cornered it out to the last handshake() call of the ehci_halt() call,
>>>>> that should set the controller in the HALT state. If I comment this handshake()
>>>>> call out, the registration is fine and the controller then looks OK (I don't
>>>>> have a hardware with a real USB bus to further test it yet).
>>>
>>> Valentin,
>>>
>>> can you specify what "real USB bus" means? Does your current hardware
>>> support USB host or device with anything connected to it?
>>
>> No. The current hardware I am testing on does not support USB since the USB bus
>> is not "wired" at all, there is no phy present (this maybe causes a problem ?).
>> What I test is if the ehci-orion USB host driver is able to register with and
>> configure the USB host controller present in the SoC, in order to prepare things
>> for when the hardware is available.
>>
>> Hopefully I get some new hardware prototypes where the USB bus is complete this
>> week so that I can test on the real setup.
>>
>
> We have now received the hardware prototype and the behavior is exactly the
> same: ETIMEOUT in ehci_halt(). If the last handshake() call is removed, the EHCI
> host controller is correctly initialized and the device on the bus is detected
> and works correctly.
>
> I thus tend to think that this is an IP (or Bobcat) internal problem and is not
> really related with the hardware nor a PHY.
>
One final update on this topic: the kernel config was missing the
CONFIG_USB_EHCI_ROOT_HUB_TT option. It turns out that the USB IP embeded a
Transaction Translator and there is a check in ehci_halt() that aborts the
routine in case of a Transaction Translator in the ehci controller. The check
however only works in the above option is enabled.
Thanks for the support
Valentin
More information about the linux-arm-kernel
mailing list