[ehci-orion] ETIMEOUT with ehci_setup()'s ehci_halt()
Valentin Longchamp
valentin.longchamp at keymile.com
Fri Jun 12 04:37:52 PDT 2015
On 06/08/2015 01:46 PM, Valentin Longchamp wrote:
> On 06/06/2015 02:17 PM, Sebastian Hesselbarth wrote:
>> On 05.06.2015 17:19, Andrew Lunn wrote:
>>> On Fri, Jun 05, 2015 at 04:34:54PM +0200, Valentin Longchamp wrote:
>>>> I am currently bringing up the USB 2.0 Host controller of the Bobcat's (98DX4122
>>>> Marvell switch) internal kirkwood CPU on a variation of Keymile's km_kirwood
>>>> hardware (kirkwood-km_kirkwood.dts).
>>>>
>>>> When the driver registers its hcd, it fails with a timemout as it can be seen in
>>>> the below log:
>>>>
>>>>> root at kmcoge5un:~# dmesg -n 8
>>>>> root at kmcoge5un:~# insmod ehci-orion.ko
>>>>> ehci-orion: EHCI orion driver
>>>>> Initializing Orion-SoC USB Host Controller
>>>>> orion-ehci f1050000.ehci: EHCI Host Controller
>>>>> orion-ehci f1050000.ehci: new USB bus registered, assigned bus number 1
>>>>> orion-ehci f1050000.ehci: reset hcs_params 0x10011 dbg=0 ind cc=0 pcc=0 ordered ports=1
>>>>> orion-ehci f1050000.ehci: reset hcc_params 0006 thresh 0 uframes 256/512/1024 park
>>>>> orion-ehci f1050000.ehci: park 0
>>>>> orion-ehci f1050000.ehci: reset command 0080002 (park)=0 ithresh=8 period=1024 Reset HALT
>>>>> orion-ehci f1050000.ehci: can't setup
>>>>> orion-ehci f1050000.ehci: USB bus 1 deregistered
>>>>> orion-ehci f1050000.ehci: init f1050000.ehci fail, -110
>>>>> orion-ehci: probe of f1050000.ehci failed with error -110
>>>>
>>>> This is very similar to this problem, except that it always happens:
>>>> https://lkml.org/lkml/2012/6/4/381
>>>>
>>>> I have cornered it out to the last handshake() call of the ehci_halt() call,
>>>> that should set the controller in the HALT state. If I comment this handshake()
>>>> call out, the registration is fine and the controller then looks OK (I don't
>>>> have a hardware with a real USB bus to further test it yet).
>>
>> Valentin,
>>
>> can you specify what "real USB bus" means? Does your current hardware
>> support USB host or device with anything connected to it?
>
> No. The current hardware I am testing on does not support USB since the USB bus
> is not "wired" at all, there is no phy present (this maybe causes a problem ?).
> What I test is if the ehci-orion USB host driver is able to register with and
> configure the USB host controller present in the SoC, in order to prepare things
> for when the hardware is available.
>
> Hopefully I get some new hardware prototypes where the USB bus is complete this
> week so that I can test on the real setup.
>
We have now received the hardware prototype and the behavior is exactly the
same: ETIMEOUT in ehci_halt(). If the last handshake() call is removed, the EHCI
host controller is correctly initialized and the device on the bus is detected
and works correctly.
I thus tend to think that this is an IP (or Bobcat) internal problem and is not
really related with the hardware nor a PHY.
Valentin
More information about the linux-arm-kernel
mailing list