[PATCH] PCI: imx6: Use "u32", not "uint32_t"

[Bjorn Helgaas]

Use "u32", not "uint32_t", for consistency.  Use "tmp", not "temp", for
consistency within the driver.

Signed-off-by: Bjorn Helgaas <bhelgaas at google.com>
---
 drivers/pci/host/pci-imx6.c |   20 ++++++++++----------
 1 file changed, 10 insertions(+), 10 deletions(-)

diff --git a/drivers/pci/host/pci-imx6.c b/drivers/pci/host/pci-imx6.c
index 2bbd38d..a032c01 100644
--- a/drivers/pci/host/pci-imx6.c
+++ b/drivers/pci/host/pci-imx6.c
@@ -354,7 +354,7 @@ static int imx6_pcie_wait_for_link(struct pcie_port *pp)
 
 static int imx6_pcie_wait_for_speed_change(struct pcie_port *pp)
 {
-	uint32_t tmp;
+	u32 tmp;
 	unsigned int retries;
 
 	for (retries = 0; retries < 200; retries++)
@@ -379,7 +379,7 @@ static irqreturn_t imx6_pcie_msi_handler(int irq, void *arg)
 static int imx6_pcie_start_link(struct pcie_port *pp)
 {
 	struct imx6_pcie *imx6_pcie = to_imx6_pcie(pp);
-	uint32_t tmp;
+	u32 tmp;
 	int ret;
 
 	/*
@@ -450,19 +450,19 @@ static void imx6_pcie_host_init(struct pcie_port *pp)
 
 static void imx6_pcie_reset_phy(struct pcie_port *pp)
 {
-	uint32_t temp;
+	u32 tmp;
 
-	pcie_phy_read(pp->dbi_base, PHY_RX_OVRD_IN_LO, &temp);
-	temp |= (PHY_RX_OVRD_IN_LO_RX_DATA_EN |
-		 PHY_RX_OVRD_IN_LO_RX_PLL_EN);
-	pcie_phy_write(pp->dbi_base, PHY_RX_OVRD_IN_LO, temp);
+	pcie_phy_read(pp->dbi_base, PHY_RX_OVRD_IN_LO, &tmp);
+	tmp |= (PHY_RX_OVRD_IN_LO_RX_DATA_EN |
+		PHY_RX_OVRD_IN_LO_RX_PLL_EN);
+	pcie_phy_write(pp->dbi_base, PHY_RX_OVRD_IN_LO, tmp);
 
 	usleep_range(2000, 3000);
 
-	pcie_phy_read(pp->dbi_base, PHY_RX_OVRD_IN_LO, &temp);
-	temp &= ~(PHY_RX_OVRD_IN_LO_RX_DATA_EN |
+	pcie_phy_read(pp->dbi_base, PHY_RX_OVRD_IN_LO, &tmp);
+	tmp &= ~(PHY_RX_OVRD_IN_LO_RX_DATA_EN |
 		  PHY_RX_OVRD_IN_LO_RX_PLL_EN);
-	pcie_phy_write(pp->dbi_base, PHY_RX_OVRD_IN_LO, temp);
+	pcie_phy_write(pp->dbi_base, PHY_RX_OVRD_IN_LO, tmp);
 }
 
 static int imx6_pcie_link_up(struct pcie_port *pp)