[PATCH v2 2/2] ARM: dts: sun5i: hsg-h702: Enable USB OTG controller

[Chen-Yu Tsai]

This tablet has proper USB OTG support, using 3 GPIO pins for
ID and VBUS detection, and also VBUS control.

Signed-off-by: Chen-Yu Tsai <wens at csie.org>
---
 arch/arm/boot/dts/sun5i-a13-hsg-h702.dts | 38 ++++++++++++++++++++++++++++++++
 1 file changed, 38 insertions(+)

diff --git a/arch/arm/boot/dts/sun5i-a13-hsg-h702.dts b/arch/arm/boot/dts/sun5i-a13-hsg-h702.dts
index 4b8808ab9711..3724b988064e 100644
--- a/arch/arm/boot/dts/sun5i-a13-hsg-h702.dts
+++ b/arch/arm/boot/dts/sun5i-a13-hsg-h702.dts
@@ -130,6 +130,10 @@
 	status = "okay";
 };
 
+&otg_sram {
+	status = "okay";
+};
+
 &pio {
 	mmc0_cd_pin_h702: mmc0_cd_pin at 0 {
 		allwinner,pins = "PG0";
@@ -137,6 +141,20 @@
 		allwinner,drive = <SUN4I_PINCTRL_10_MA>;
 		allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
 	};
+
+	usb0_id_detect_pin: usb0_id_detect_pin at 0 {
+		allwinner,pins = "PG2";
+		allwinner,function = "gpio_in";
+		allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+		allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+	};
+
+	usb0_vbus_detect_pin: usb0_vbus_detect_pin at 0 {
+		allwinner,pins = "PG1";
+		allwinner,function = "gpio_in";
+		allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+		allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+	};
 };
 
 #include "axp209.dtsi"
@@ -172,13 +190,33 @@
 	regulator-name = "vcc-wifi";
 };
 
+&reg_usb0_vbus {
+	pinctrl-0 = <&usb0_vbus_pin_a>;
+	gpio = <&pio 6 12 GPIO_ACTIVE_HIGH>; /* PG12 */
+	status = "okay";
+};
+
 &uart1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&uart1_pins_b>;
 	status = "okay";
 };
 
+&usb_otg {
+	dr_mode = "otg";
+	status = "okay";
+};
+
+&usb0_vbus_pin_a {
+	allwinner,pins = "PG12";
+};
+
 &usbphy {
+	pinctrl-names = "default";
+	pinctrl-0 = <&usb0_id_detect_pin>, <&usb0_vbus_detect_pin>;
+	usb0_id_det-gpios = <&pio 6 2 GPIO_ACTIVE_HIGH>; /* PG2 */
+	usb0_vbus_det-gpios = <&pio 6 1 GPIO_ACTIVE_HIGH>; /* PG1 */
+	usb0_vbus-supply = <&reg_usb0_vbus>;
 	usb1_vbus-supply = <&reg_ldo3>;
 	status = "okay";
 };
-- 
2.5.0