[PATCH v3 3/5] usb: phy: add usb3.0 phy driver for mt65xx SoCs
chunfeng yun
chunfeng.yun at mediatek.com
Fri Jul 31 05:25:50 PDT 2015
hi,
On Tue, 2015-07-28 at 11:17 +0530, Kishon Vijay Abraham I wrote:
> Hi,
>
> On Sunday 26 July 2015 08:21 AM, chunfeng yun wrote:
> > hi,
> > On Wed, 2015-07-22 at 09:21 -0500, Felipe Balbi wrote:
> >> Hi,
> >>
> >> On Wed, Jul 22, 2015 at 10:05:43PM +0800, Chunfeng Yun wrote:
> >>> support usb3.0 phy of mt65xx SoCs
> >>>
> >>> Signed-off-by: Chunfeng Yun <chunfeng.yun at mediatek.com>
> >>
> >> you missed Kishon here.
> >>
> > Thank you.
> >>> ---
> >>> drivers/phy/Kconfig | 9 +
> >>> drivers/phy/Makefile | 1 +
> >>> drivers/phy/phy-mt65xx-usb3.c | 426 ++++++++++++++++++++++++++++++++++++++++++
> >>> 3 files changed, 436 insertions(+)
> >>> create mode 100644 drivers/phy/phy-mt65xx-usb3.c
> >>>
> >>> diff --git a/drivers/phy/Kconfig b/drivers/phy/Kconfig
> >>> index c0e6ede..019cf8b 100644
> >>> --- a/drivers/phy/Kconfig
> >>> +++ b/drivers/phy/Kconfig
> >>> @@ -193,6 +193,15 @@ config PHY_HIX5HD2_SATA
> >>> help
> >>> Support for SATA PHY on Hisilicon hix5hd2 Soc.
> >>>
> >>> +config PHY_MT65XX_USB3
> >>> + tristate "Mediatek USB3.0 PHY Driver"
> >>> + depends on ARCH_MEDIATEK && OF
> >>> + select GENERIC_PHY
> >>> + help
> >>> + Say 'Y' here to add support for Mediatek USB3.0 PHY driver
> >>> + for mt65xx SoCs. it supports two usb2.0 ports and
> >>> + one usb3.0 port.
> >>> +
> >>> config PHY_SUN4I_USB
> >>> tristate "Allwinner sunxi SoC USB PHY driver"
> >>> depends on ARCH_SUNXI && HAS_IOMEM && OF
> >>> diff --git a/drivers/phy/Makefile b/drivers/phy/Makefile
> >>> index f344e1b..3ceff2a 100644
> >>> --- a/drivers/phy/Makefile
> >>> +++ b/drivers/phy/Makefile
> >>> @@ -22,6 +22,7 @@ obj-$(CONFIG_TI_PIPE3) += phy-ti-pipe3.o
> >>> obj-$(CONFIG_TWL4030_USB) += phy-twl4030-usb.o
> >>> obj-$(CONFIG_PHY_EXYNOS5250_SATA) += phy-exynos5250-sata.o
> >>> obj-$(CONFIG_PHY_HIX5HD2_SATA) += phy-hix5hd2-sata.o
> >>> +obj-$(CONFIG_PHY_MT65XX_USB3) += phy-mt65xx-usb3.o
> >>> obj-$(CONFIG_PHY_SUN4I_USB) += phy-sun4i-usb.o
> >>> obj-$(CONFIG_PHY_SUN9I_USB) += phy-sun9i-usb.o
> >>> obj-$(CONFIG_PHY_SAMSUNG_USB2) += phy-exynos-usb2.o
> >>> diff --git a/drivers/phy/phy-mt65xx-usb3.c b/drivers/phy/phy-mt65xx-usb3.c
> >>> new file mode 100644
> >>> index 0000000..5da4534
> >>> --- /dev/null
> >>> +++ b/drivers/phy/phy-mt65xx-usb3.c
> >>> @@ -0,0 +1,426 @@
> >>> +/*
> >>> + * Copyright (c) 2015 MediaTek Inc.
> >>> + * Author: Chunfeng.Yun <chunfeng.yun at mediatek.com>
> >>> + *
> >>> + * This software is licensed under the terms of the GNU General Public
> >>> + * License version 2, as published by the Free Software Foundation, and
> >>> + * may be copied, distributed, and modified under those terms.
> >>> + *
> >>> + * This program is distributed in the hope that it will be useful,
> >>> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> >>> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> >>> + * GNU General Public License for more details.
> >>> + *
> >>> + */
> >>> +
> >>> +#include <linux/clk.h>
> >>> +#include <linux/delay.h>
> >>> +#include <linux/io.h>
> >>> +#include <linux/module.h>
> >>> +#include <linux/of_address.h>
> >>> +#include <linux/of_device.h>
> >>> +#include <linux/of_gpio.h>
> >>> +#include <linux/of.h>
> >>> +#include <linux/phy/phy.h>
> >>> +#include <linux/platform_device.h>
> >>> +#include <linux/pm_runtime.h>
> >>> +#include <linux/regulator/consumer.h>
>
> Lot of these #include are not required. Add only those what are required by
> this driver.
The dummy header files will be removed later
> >>> +#include <linux/resource.h>
> >>> +
> >>> +/*
> >>> + * for sifslv2 register
> >>> + * relative to USB3_SIF2_BASE base address
> >>> + */
> >>> +#define SSUSB_SIFSLV_SPLLC (0x0000)
> >>> +#define SSUSB_SIFSLV_U2PHY_COM_BASE (0x0800)
>
> Looks like all this base address can come from dt.
The phy supports multi-ports, and these are sub-segment registers for
port0, and other ports can be calculated from the bases. So I think it's
better to use the same base address in dts
> >>> +#define SSUSB_SIFSLV_U3PHYD_BASE (0x0900)
> >>> +#define SSUSB_USB30_PHYA_SIV_B_BASE (0x0b00)
> >>> +#define SSUSB_SIFSLV_U3PHYA_DA_BASE (0x0c00)
> >>> +
> >>> +/*port1 refs. +0x800(refer to port0)*/
> >>> +#define U3P_PORT_INTERVAL (0x800) /*based on port0 */
> >>> +#define U3P_PHY_DELTA(index) ((U3P_PORT_INTERVAL) * (index))
> >>> +
> >>> +#define U3P_USBPHYACR0 (SSUSB_SIFSLV_U2PHY_COM_BASE + 0x0000)
> >>> +#define PA0_RG_U2PLL_FORCE_ON (0x1 << 15)
> >>> +
> >>> +#define U3P_USBPHYACR2 (SSUSB_SIFSLV_U2PHY_COM_BASE + 0x0008)
> >>> +#define PA2_RG_SIF_U2PLL_FORCE_EN (0x1 << 18)
> >>> +
> >>> +#define U3P_USBPHYACR5 (SSUSB_SIFSLV_U2PHY_COM_BASE + 0x0014)
> >>> +#define PA5_RG_U2_HSTX_SRCTRL (0x7 << 12)
> >>> +#define PA5_RG_U2_HSTX_SRCTRL_VAL(x) ((0x7 & (x)) << 12)
> >>> +#define PA5_RG_U2_HS_100U_U3_EN (0x1 << 11)
> >>> +
> >>> +#define U3P_USBPHYACR6 (SSUSB_SIFSLV_U2PHY_COM_BASE + 0x0018)
> >>> +#define PA6_RG_U2_ISO_EN (0x1 << 31)
> >>> +#define PA6_RG_U2_BC11_SW_EN (0x1 << 23)
> >>> +#define PA6_RG_U2_OTG_VBUSCMP_EN (0x1 << 20)
> >>> +
> >>> +#define U3P_U2PHYACR4 (SSUSB_SIFSLV_U2PHY_COM_BASE + 0x0020)
> >>> +#define P2C_RG_USB20_GPIO_CTL (0x1 << 9)
> >>> +#define P2C_USB20_GPIO_MODE (0x1 << 8)
> >>> +#define P2C_U2_GPIO_CTR_MSK (P2C_RG_USB20_GPIO_CTL | P2C_USB20_GPIO_MODE)
> >>> +
> >>> +#define U3D_U2PHYDCR0 (SSUSB_SIFSLV_U2PHY_COM_BASE + 0x0060)
> >>> +#define P2C_RG_SIF_U2PLL_FORCE_ON (0x1 << 24)
> >>> +
> >>> +#define U3P_U2PHYDTM0 (SSUSB_SIFSLV_U2PHY_COM_BASE + 0x0068)
> >>> +#define P2C_FORCE_UART_EN (0x1 << 26)
> >>> +#define P2C_FORCE_DATAIN (0x1 << 23)
> >>> +#define P2C_FORCE_DM_PULLDOWN (0x1 << 21)
> >>> +#define P2C_FORCE_DP_PULLDOWN (0x1 << 20)
> >>> +#define P2C_FORCE_XCVRSEL (0x1 << 19)
> >>> +#define P2C_FORCE_SUSPENDM (0x1 << 18)
> >>> +#define P2C_FORCE_TERMSEL (0x1 << 17)
> >>> +#define P2C_RG_DATAIN (0xf << 10)
> >>> +#define P2C_RG_DATAIN_VAL(x) ((0xf & (x)) << 10)
> >>> +#define P2C_RG_DMPULLDOWN (0x1 << 7)
> >>> +#define P2C_RG_DPPULLDOWN (0x1 << 6)
> >>> +#define P2C_RG_XCVRSEL (0x3 << 4)
> >>> +#define P2C_RG_XCVRSEL_VAL(x) ((0x3 & (x)) << 4)
> >>> +#define P2C_RG_SUSPENDM (0x1 << 3)
> >>> +#define P2C_RG_TERMSEL (0x1 << 2)
> >>> +#define P2C_DTM0_PART_MASK \
> >>> + (P2C_FORCE_DATAIN | P2C_FORCE_DM_PULLDOWN | \
> >>> + P2C_FORCE_DP_PULLDOWN | P2C_FORCE_XCVRSEL | \
> >>> + P2C_FORCE_TERMSEL | P2C_RG_DMPULLDOWN | \
> >>> + P2C_RG_DPPULLDOWN | P2C_RG_TERMSEL)
> >>> +
> >>> +#define U3P_U2PHYDTM1 (SSUSB_SIFSLV_U2PHY_COM_BASE + 0x006C)
> >>> +#define P2C_RG_UART_EN (0x1 << 16)
> >>> +#define P2C_RG_VBUSVALID (0x1 << 5)
> >>> +#define P2C_RG_SESSEND (0x1 << 4)
> >>> +#define P2C_RG_AVALID (0x1 << 2)
> >>> +
> >>> +#define U3P_U3_PHYA_REG0 (SSUSB_USB30_PHYA_SIV_B_BASE + 0x0000)
> >>> +#define P3A_RG_U3_VUSB10_ON (1 << 5)
> >>> +
> >>> +#define U3P_U3_PHYA_REG6 (SSUSB_USB30_PHYA_SIV_B_BASE + 0x0018)
> >>> +#define P3A_RG_TX_EIDLE_CM (0xf << 28)
> >>> +#define P3A_RG_TX_EIDLE_CM_VAL(x) ((0xf & (x)) << 28)
> >>> +
> >>> +#define U3P_U3_PHYA_REG9 (SSUSB_USB30_PHYA_SIV_B_BASE + 0x0024)
> >>> +#define P3A_RG_RX_DAC_MUX (0x1f << 1)
> >>> +#define P3A_RG_RX_DAC_MUX_VAL(x) ((0x1f & (x)) << 1)
> >>> +
> >>> +#define U3P_U3PHYA_DA_REG0 (SSUSB_SIFSLV_U3PHYA_DA_BASE + 0x0)
> >>> +#define P3A_RG_XTAL_EXT_EN_U3 (0x3 << 10)
> >>> +#define P3A_RG_XTAL_EXT_EN_U3_VAL(x) ((0x3 & (x)) << 10)
> >>> +
> >>> +#define U3P_PHYD_CDR1 (SSUSB_SIFSLV_U3PHYD_BASE + 0x5c)
> >>> +#define P3D_RG_CDR_BIR_LTD1 (0x1f << 24)
> >>> +#define P3D_RG_CDR_BIR_LTD1_VAL(x) ((0x1f & (x)) << 24)
> >>> +#define P3D_RG_CDR_BIR_LTD0 (0x1f << 8)
> >>> +#define P3D_RG_CDR_BIR_LTD0_VAL(x) ((0x1f & (x)) << 8)
> >>> +
> >>> +#define U3P_XTALCTL3 (SSUSB_SIFSLV_SPLLC + 0x18)
> >>> +#define XC3_RG_U3_XTAL_RX_PWD (0x1 << 9)
> >>> +#define XC3_RG_U3_FRC_XTAL_RX_PWD (0x1 << 8)
> >>> +
> >>> +#define MT65XX_MAX_PHYS 2
> >>> +
> >>> +struct mt65xx_phy_instance {
> >>> + struct phy *phy;
> >>> + u32 index;
> >>> + u32 delta; /* increament refers to port0 */
> >>> +};
> >>> +
> >>> +struct mt65xx_u3phy {
> >>> + struct device *dev;
> >>> + void __iomem *sif_base; /* include sif2 */
> >>> + struct clk *u3phya_ref; /* reference clock of usb3 anolog phy */
> >>> + struct mt65xx_phy_instance phys[MT65XX_MAX_PHYS];
> >>> +};
> >>> +
> >>> +static struct mt65xx_u3phy *to_usbdrd_phy(
> >>> + struct mt65xx_phy_instance *instance)
> >>> +{
> >>> + return container_of((instance), struct mt65xx_u3phy,
> >>> + phys[(instance)->index]);
> >>> +}
> >>> +
> .
> .
> <<snip>>
> .
> .
>
> >>> +static struct phy *mt65xx_phy_xlate(struct device *dev,
> >>> + struct of_phandle_args *args)
> >>> +{
> >>> + struct mt65xx_u3phy *u3phy = dev_get_drvdata(dev);
> >>> +
> >>> + if (WARN_ON(args->args[0] > MT65XX_MAX_PHYS))
> >>> + return ERR_PTR(-ENODEV);
> >>> +
> >>> + return u3phy->phys[args->args[0]].phy;
> >>> +}
>
> If the driver doesn't have to get any data from dt, then custom xlate is not
> required at all. All you have to do is create separate nodes for every
> individual phy and keep it as the child node of the phy_provider dt node. Note
> that the phy consumer dt node should now use the label given for the chld-nodes
> and not the phy_provider. Look at drivers/phy/phy-miphy365x.c for reference.
>
It is multi-port PHY, and these ports share some registers from offset
[0, 0x7ff], and port0 segment is [0x800, 0xfff], port1 segment is
[0x1000, 0x17ff], etc, so I think maybe it is not suitable to create
separate nodes in dts for each port.
BTW: I refer to phy-exynos5-usbdrd.c which is multi-channel usb3.0 phy
to write this driver.
thanks
> Cheers
> Kishon
More information about the linux-arm-kernel
mailing list