[PATCH 5/5] ARM: dts: sun7i: Add dts file for Wits Pro A20 DKT

Fri Jul 31 03:20:28 PDT 2015

On Fri, Jul 31, 2015 at 10:59:54AM +0200, Hans de Goede wrote:
> From: Jelle de Jong <jelledejong at powercraft.nl>
> 
> The Wits Pro A20 DKT is an A20 Development KiT with 1G RAM, 4G NAND,
> sdio wifi, 1Gbit ethernet, 1024x768 lcd screen with ft5x_ts touchscreen
> and a ton of IO connectors.
> 
> Note there seem to be multiple sdcard slots on the board (4 in total), but
> other then mmc0 none of these are hooked up by default, there is a ton of
> dip-switches which likely allow hooking some of these up, but the
> documentation of the board only describes the use of a fraction of them,
> so for now we only support mmc0.
> 
> Signed-off-by: Jelle de Jong <jelledejong at powercraft.nl>
> Signed-off-by: Hans de Goede <hdegoede at redhat.com>
> ---
> Also see: http://www.merrii.com/en/pla_d.asp?id=163
> ---
>  arch/arm/boot/dts/Makefile                       |   3 +-
>  arch/arm/boot/dts/sun7i-a20-wits-pro-a20-dkt.dts | 209 +++++++++++++++++++++++
>  2 files changed, 211 insertions(+), 1 deletion(-)
>  create mode 100644 arch/arm/boot/dts/sun7i-a20-wits-pro-a20-dkt.dts
> 
> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> index f830e1f..151a413 100644
> --- a/arch/arm/boot/dts/Makefile
> +++ b/arch/arm/boot/dts/Makefile
> @@ -595,7 +595,8 @@ dtb-$(CONFIG_MACH_SUN7I) += \
>  	sun7i-a20-orangepi-mini.dtb \
>  	sun7i-a20-pcduino3.dtb \
>  	sun7i-a20-pcduino3-nano.dtb \
> -	sun7i-a20-wexler-tab7200.dtb
> +	sun7i-a20-wexler-tab7200.dtb \
> +        sun7i-a20-wits-pro-a20-dkt.dtb

The indentation is off.

>  dtb-$(CONFIG_MACH_SUN8I) += \
>  	sun8i-a23-evb.dtb \
>  	sun8i-a23-ippo-q8h-v5.dtb \
> diff --git a/arch/arm/boot/dts/sun7i-a20-wits-pro-a20-dkt.dts b/arch/arm/boot/dts/sun7i-a20-wits-pro-a20-dkt.dts
> new file mode 100644
> index 0000000..db4d32c
> --- /dev/null
> +++ b/arch/arm/boot/dts/sun7i-a20-wits-pro-a20-dkt.dts
> @@ -0,0 +1,209 @@
> +/*
> + * Copyright 2015 Jelle de Jong <jelledejong at powercraft.nl>
> + *
> + * This file is dual-licensed: you can use it either under the terms
> + * of the GPL or the X11 license, at your option. Note that this dual
> + * licensing only applies to this file, and not this project as a
> + * whole.
> + *
> + *  a) This file is free software; you can redistribute it and/or
> + *     modify it under the terms of the GNU General Public License as
> + *     published by the Free Software Foundation; either version 2 of the
> + *     License, or (at your option) any later version.
> + *
> + *     This file is distributed in the hope that it will be useful,
> + *     but WITHOUT ANY WARRANTY; without even the implied warranty of
> + *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
> + *     GNU General Public License for more details.
> + *
> + * Or, alternatively,
> + *
> + *  b) Permission is hereby granted, free of charge, to any person
> + *     obtaining a copy of this software and associated documentation
> + *     files (the "Software"), to deal in the Software without
> + *     restriction, including without limitation the rights to use,
> + *     copy, modify, merge, publish, distribute, sublicense, and/or
> + *     sell copies of the Software, and to permit persons to whom the
> + *     Software is furnished to do so, subject to the following
> + *     conditions:
> + *
> + *     The above copyright notice and this permission notice shall be
> + *     included in all copies or substantial portions of the Software.
> + *
> + *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
> + *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
> + *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
> + *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
> + *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
> + *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
> + *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
> + *     OTHER DEALINGS IN THE SOFTWARE.
> + */
> +
> +/dts-v1/;
> +#include "sun7i-a20.dtsi"
> +#include "sunxi-common-regulators.dtsi"
> +
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/input/input.h>
> +#include <dt-bindings/interrupt-controller/irq.h>
> +
> +/ {
> +	model = "Wits Pro A20 DKT";
> +	compatible = "wits,pro-a20-dkt", "allwinner,sun7i-a20";
> +
> +	aliases {
> +		serial0 = &uart0;
> +	};
> +
> +	chosen {
> +		stdout-path = "serial0:115200n8";
> +	};
> +
> +	reg_vmmc3: vmmc3 {
> +		compatible = "regulator-fixed";
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&vmmc3_pin_ap6xxx_wl_regon>;
> +		regulator-name = "vmmc3";
> +		regulator-min-microvolt = <3300000>;
> +		regulator-max-microvolt = <3300000>;
> +		enable-active-high;
> +		gpio = <&pio 7 9 GPIO_ACTIVE_HIGH>; /* PH9 */
> +	};

It's not really vmmc. The reg_on stuff is actually more of a reset
line: when tied to VCC, the WLAN part of the chip and its regulators
are enabled, while when it's tied to ground, the WLAN is in reset, and
the internal regulators disabled.

So it can be seen as either an active-low reset line, or an
active-high regulator for the WiFi part, but VMMC is the power line of
the MMC bus itself, which usually is provided by a regulator through
the pin 22 of the AP6210, usually tied directly to the 3.3V line.

So you actually have two regulators here: one for vmmc (reg_3v3), and
one for reg_on which is the one that you just defined.

Note that it's a bit of a pain for now to support such cases, as
there's nothing to tie something from the DT to an SDIO device. I
don't have a better solution than marking it always-on at the moment,
with a big FIXME comment on top... :/

Maxime

-- 
Maxime Ripard, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 819 bytes
Desc: Digital signature
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20150731/aafae621/attachment-0001.sig>