[PATCH v1 6/7] ARM: dts: apq8064: Add DT support for GSBI6 and for UART pin mux

[Srinivas Kandagatla]

From: Pramod Gurav <pramod.gurav at smartplayin.com>

This change adds DT support for GSBI6 and muxes the gpio pins
as UART lines. Also defines a alias for serial port on these lines.

Signed-off-by: Pramod Gurav <pramod.gurav at smartplayin.com>
[Srinivas Kandagatla]: fix pinctrl location and rename alias correctly
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla at linaro.org>
---
 arch/arm/boot/dts/qcom-apq8064-ifc6410.dts | 13 +++++++++++++
 arch/arm/boot/dts/qcom-apq8064.dtsi        | 30 +++++++++++++++++++++++++++++-
 2 files changed, 42 insertions(+), 1 deletion(-)

diff --git a/arch/arm/boot/dts/qcom-apq8064-ifc6410.dts b/arch/arm/boot/dts/qcom-apq8064-ifc6410.dts
index cdfcf02..ec6a736 100644
--- a/arch/arm/boot/dts/qcom-apq8064-ifc6410.dts
+++ b/arch/arm/boot/dts/qcom-apq8064-ifc6410.dts
@@ -7,6 +7,7 @@
 
 	aliases {
 		serial0 = &gsbi7_serial;
+		serial1 = &gsbi6_serial;
 	};
 
 	soc {
@@ -125,6 +126,18 @@
 			};
 		};
 
+		gsbi at 16500000 {
+			status = "ok";
+			qcom,mode = <GSBI_PROT_I2C_UART>;
+
+			serial at 16540000 {
+				status = "ok";
+
+				pinctrl-names = "default";
+				pinctrl-0 = <&uart_pins>;
+			};
+		};
+
 		gsbi at 16600000 {
 			status = "ok";
 			qcom,mode = <GSBI_PROT_I2C_UART>;
diff --git a/arch/arm/boot/dts/qcom-apq8064.dtsi b/arch/arm/boot/dts/qcom-apq8064.dtsi
index da214f1..b7c282b 100644
--- a/arch/arm/boot/dts/qcom-apq8064.dtsi
+++ b/arch/arm/boot/dts/qcom-apq8064.dtsi
@@ -126,6 +126,13 @@
 					function = "gsbi3";
 				};
 			};
+
+			uart_pins: uart_pins {
+				mux {
+					pins = "gpio14", "gpio15", "gpio16", "gpio17";
+					function = "gsbi6";
+				};
+			};
 		};
 
 		intc: interrupt-controller at 2000000 {
@@ -248,7 +255,6 @@
 			#address-cells = <1>;
 			#size-cells = <1>;
 			ranges;
-
 			i2c3: i2c at 16280000 {
 				compatible = "qcom,i2c-qup-v1.1.1";
 				reg = <0x16280000 0x1000>;
@@ -259,6 +265,28 @@
 			};
 		};
 
+		gsbi6: gsbi at 16500000 {
+			status = "disabled";
+			compatible = "qcom,gsbi-v1.0.0";
+			cell-index = <6>;
+			reg = <0x16500000 0x03>;
+			clocks = <&gcc GSBI6_H_CLK>;
+			clock-names = "iface";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+
+			gsbi6_serial: serial at 16540000 {
+				compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm";
+				reg = <0x16540000 0x100>,
+				      <0x16500000 0x03>;
+				interrupts = <0 156 0x0>;
+				clocks = <&gcc GSBI6_UART_CLK>, <&gcc GSBI6_H_CLK>;
+				clock-names = "core", "iface";
+				status = "disabled";
+			};
+		};
+
 		gsbi7: gsbi at 16600000 {
 			status = "disabled";
 			compatible = "qcom,gsbi-v1.0.0";
-- 
1.9.1