[V3] [TWL4030 MADC] Fix ADC[3:6] readings

[Adam YH Lee]

MADC[3:6] reads incorrect values without these two following changes:

- enable the 3v1 bias regulator for ADC[3:6]
- configure ADC[3:6] lines as input, not as USB

Signed-off-by: Adam YH Lee <adam.yh.lee at gmail.com>
---
 drivers/iio/adc/twl4030-madc.c | 36 ++++++++++++++++++++++++++++++++++++
 1 file changed, 36 insertions(+)

diff --git a/drivers/iio/adc/twl4030-madc.c b/drivers/iio/adc/twl4030-madc.c
index 94c5f05..ae33eba 100644
--- a/drivers/iio/adc/twl4030-madc.c
+++ b/drivers/iio/adc/twl4030-madc.c
@@ -45,13 +45,18 @@
 #include <linux/types.h>
 #include <linux/gfp.h>
 #include <linux/err.h>
+#include <linux/regulator/consumer.h>
 
 #include <linux/iio/iio.h>
 
+#define TWL4030_USB_SEL_MADC_MCPC	(1<<3)
+#define TWL4030_USB_CARKIT_ANA_CTRL	0xBB
+
 /**
  * struct twl4030_madc_data - a container for madc info
  * @dev:		Pointer to device structure for madc
  * @lock:		Mutex protecting this data structure
+ * @regulator:		Pointer to bias regulator for madc
  * @requests:		Array of request struct corresponding to SW1, SW2 and RT
  * @use_second_irq:	IRQ selection (main or co-processor)
  * @imr:		Interrupt mask register of MADC
@@ -60,6 +65,7 @@
 struct twl4030_madc_data {
 	struct device *dev;
 	struct mutex lock;	/* mutex protecting this data structure */
+	struct regulator *usb3v1;
 	struct twl4030_madc_request requests[TWL4030_MADC_NUM_METHODS];
 	bool use_second_irq;
 	u8 imr;
@@ -848,6 +854,33 @@ static int twl4030_madc_probe(struct platform_device *pdev)
 		goto err_i2c;
 	}
 
+	/* Configure MADC[3:6] */
+	ret = twl_i2c_read_u8(TWL_MODULE_USB, &regval,
+			TWL4030_USB_CARKIT_ANA_CTRL);
+	if (ret) {
+		dev_err(&pdev->dev, "unable to read reg CARKIT_ANA_CTRL  0x%X\n",
+				TWL4030_USB_CARKIT_ANA_CTRL);
+		goto err_i2c;
+	}
+	regval |= TWL4030_USB_SEL_MADC_MCPC;
+	ret = twl_i2c_write_u8(TWL_MODULE_USB, regval,
+				 TWL4030_USB_CARKIT_ANA_CTRL);
+	if (ret) {
+		dev_err(&pdev->dev, "unable to write reg CARKIT_ANA_CTRL 0x%X\n",
+				TWL4030_USB_CARKIT_ANA_CTRL);
+		goto err_i2c;
+	}
+
+
+	/* Enable 3v1 bias regulator for MADC[3:6] */
+	madc->usb3v1 = devm_regulator_get(madc->dev, "vusb3v1");
+	if (IS_ERR(madc->usb3v1))
+		return -ENODEV;
+
+	ret = regulator_enable(madc->usb3v1);
+	if (ret)
+		dev_err(madc->dev, "could not enable 3v1 bias regulator\n");
+
 	return 0;
 
 err_i2c:
@@ -867,6 +900,9 @@ static int twl4030_madc_remove(struct platform_device *pdev)
 	twl4030_madc_set_current_generator(madc, 0, 0);
 	twl4030_madc_set_power(madc, 0);
 
+	regulator_disable(madc->usb3v1);
+	devm_regulator_put(madc->usb3v1);
+
 	return 0;
 }
 
-- 
2.1.4