[PATCH v4 3/5] tty/serial: at91: remove bunch of macros to access UART registers
Nicolas Ferre
nicolas.ferre at atmel.com
Mon Jul 20 05:24:38 PDT 2015
Le 02/07/2015 15:18, Cyrille Pitchen a écrit :
> This patch replaces the UART_PUT_*, resp. UART_GET_*, macros by
> atmel_uart_writel(), resp. atmel_uart_readl(), inline function calls.
>
> Signed-off-by: Cyrille Pitchen <cyrille.pitchen at atmel.com>
Ok with this move:
Acked-by: Nicolas Ferre <nicolas.ferre at atmel.com>
> ---
> drivers/tty/serial/atmel_serial.c | 313 +++++++++++++++++++-------------------
> 1 file changed, 159 insertions(+), 154 deletions(-)
>
> diff --git a/drivers/tty/serial/atmel_serial.c b/drivers/tty/serial/atmel_serial.c
> index 2a8f528153e7..e7c337de31d1 100644
> --- a/drivers/tty/serial/atmel_serial.c
> +++ b/drivers/tty/serial/atmel_serial.c
> @@ -88,37 +88,6 @@ static void atmel_stop_rx(struct uart_port *port);
>
> #define ATMEL_ISR_PASS_LIMIT 256
>
> -/* UART registers. CR is write-only, hence no GET macro */
> -#define UART_PUT_CR(port,v) __raw_writel(v, (port)->membase + ATMEL_US_CR)
> -#define UART_GET_MR(port) __raw_readl((port)->membase + ATMEL_US_MR)
> -#define UART_PUT_MR(port,v) __raw_writel(v, (port)->membase + ATMEL_US_MR)
> -#define UART_PUT_IER(port,v) __raw_writel(v, (port)->membase + ATMEL_US_IER)
> -#define UART_PUT_IDR(port,v) __raw_writel(v, (port)->membase + ATMEL_US_IDR)
> -#define UART_GET_IMR(port) __raw_readl((port)->membase + ATMEL_US_IMR)
> -#define UART_GET_CSR(port) __raw_readl((port)->membase + ATMEL_US_CSR)
> -#define UART_GET_CHAR(port) __raw_readl((port)->membase + ATMEL_US_RHR)
> -#define UART_PUT_CHAR(port,v) __raw_writel(v, (port)->membase + ATMEL_US_THR)
> -#define UART_GET_BRGR(port) __raw_readl((port)->membase + ATMEL_US_BRGR)
> -#define UART_PUT_BRGR(port,v) __raw_writel(v, (port)->membase + ATMEL_US_BRGR)
> -#define UART_PUT_RTOR(port,v) __raw_writel(v, (port)->membase + ATMEL_US_RTOR)
> -#define UART_PUT_TTGR(port, v) __raw_writel(v, (port)->membase + ATMEL_US_TTGR)
> -#define UART_GET_IP_NAME(port) __raw_readl((port)->membase + ATMEL_US_NAME)
> -#define UART_GET_IP_VERSION(port) __raw_readl((port)->membase + ATMEL_US_VERSION)
> -
> - /* PDC registers */
> -#define UART_PUT_PTCR(port,v) __raw_writel(v, (port)->membase + ATMEL_PDC_PTCR)
> -#define UART_GET_PTSR(port) __raw_readl((port)->membase + ATMEL_PDC_PTSR)
> -
> -#define UART_PUT_RPR(port,v) __raw_writel(v, (port)->membase + ATMEL_PDC_RPR)
> -#define UART_GET_RPR(port) __raw_readl((port)->membase + ATMEL_PDC_RPR)
> -#define UART_PUT_RCR(port,v) __raw_writel(v, (port)->membase + ATMEL_PDC_RCR)
> -#define UART_PUT_RNPR(port,v) __raw_writel(v, (port)->membase + ATMEL_PDC_RNPR)
> -#define UART_PUT_RNCR(port,v) __raw_writel(v, (port)->membase + ATMEL_PDC_RNCR)
> -
> -#define UART_PUT_TPR(port,v) __raw_writel(v, (port)->membase + ATMEL_PDC_TPR)
> -#define UART_PUT_TCR(port,v) __raw_writel(v, (port)->membase + ATMEL_PDC_TCR)
> -#define UART_GET_TCR(port) __raw_readl((port)->membase + ATMEL_PDC_TCR)
> -
> struct atmel_dma_buffer {
> unsigned char *buf;
> dma_addr_t dma_addr;
> @@ -212,6 +181,16 @@ to_atmel_uart_port(struct uart_port *uart)
> return container_of(uart, struct atmel_uart_port, uart);
> }
>
> +static inline u32 atmel_uart_readl(struct uart_port *port, u32 reg)
> +{
> + return __raw_readl(port->membase + reg);
> +}
> +
> +static inline void atmel_uart_writel(struct uart_port *port, u32 reg, u32 value)
> +{
> + __raw_writel(value, port->membase + reg);
> +}
> +
> #ifdef CONFIG_SERIAL_ATMEL_PDC
> static bool atmel_use_pdc_rx(struct uart_port *port)
> {
> @@ -257,7 +236,7 @@ static unsigned int atmel_get_lines_status(struct uart_port *port)
> struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
> unsigned int status, ret = 0;
>
> - status = UART_GET_CSR(port);
> + status = atmel_uart_readl(port, ATMEL_US_CSR);
>
> mctrl_gpio_get(atmel_port->gpios, &ret);
>
> @@ -304,9 +283,9 @@ static int atmel_config_rs485(struct uart_port *port,
> unsigned int mode;
>
> /* Disable interrupts */
> - UART_PUT_IDR(port, atmel_port->tx_done_mask);
> + atmel_uart_writel(port, ATMEL_US_IDR, atmel_port->tx_done_mask);
>
> - mode = UART_GET_MR(port);
> + mode = atmel_uart_readl(port, ATMEL_US_MR);
>
> /* Resetting serial mode to RS232 (0x0) */
> mode &= ~ATMEL_US_USMODE;
> @@ -316,7 +295,8 @@ static int atmel_config_rs485(struct uart_port *port,
> if (rs485conf->flags & SER_RS485_ENABLED) {
> dev_dbg(port->dev, "Setting UART to RS485\n");
> atmel_port->tx_done_mask = ATMEL_US_TXEMPTY;
> - UART_PUT_TTGR(port, rs485conf->delay_rts_after_send);
> + atmel_uart_writel(port, ATMEL_US_TTGR,
> + rs485conf->delay_rts_after_send);
> mode |= ATMEL_US_USMODE_RS485;
> } else {
> dev_dbg(port->dev, "Setting UART to RS232\n");
> @@ -326,10 +306,10 @@ static int atmel_config_rs485(struct uart_port *port,
> else
> atmel_port->tx_done_mask = ATMEL_US_TXRDY;
> }
> - UART_PUT_MR(port, mode);
> + atmel_uart_writel(port, ATMEL_US_MR, mode);
>
> /* Enable interrupts */
> - UART_PUT_IER(port, atmel_port->tx_done_mask);
> + atmel_uart_writel(port, ATMEL_US_IER, atmel_port->tx_done_mask);
>
> return 0;
> }
> @@ -339,7 +319,9 @@ static int atmel_config_rs485(struct uart_port *port,
> */
> static u_int atmel_tx_empty(struct uart_port *port)
> {
> - return (UART_GET_CSR(port) & ATMEL_US_TXEMPTY) ? TIOCSER_TEMT : 0;
> + return (atmel_uart_readl(port, ATMEL_US_CSR) & ATMEL_US_TXEMPTY) ?
> + TIOCSER_TEMT :
> + 0;
> }
>
> /*
> @@ -348,13 +330,14 @@ static u_int atmel_tx_empty(struct uart_port *port)
> static void atmel_set_mctrl(struct uart_port *port, u_int mctrl)
> {
> unsigned int control = 0;
> - unsigned int mode = UART_GET_MR(port);
> + unsigned int mode = atmel_uart_readl(port, ATMEL_US_MR);
> unsigned int rts_paused, rts_ready;
> struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
>
> /* override mode to RS485 if needed, otherwise keep the current mode */
> if (port->rs485.flags & SER_RS485_ENABLED) {
> - UART_PUT_TTGR(port, port->rs485.delay_rts_after_send);
> + atmel_uart_writel(port, ATMEL_US_TTGR,
> + port->rs485.delay_rts_after_send);
> mode &= ~ATMEL_US_USMODE;
> mode |= ATMEL_US_USMODE_RS485;
> }
> @@ -384,7 +367,7 @@ static void atmel_set_mctrl(struct uart_port *port, u_int mctrl)
> else
> control |= ATMEL_US_DTRDIS;
>
> - UART_PUT_CR(port, control);
> + atmel_uart_writel(port, ATMEL_US_CR, control);
>
> mctrl_gpio_set(atmel_port->gpios, mctrl);
>
> @@ -395,7 +378,7 @@ static void atmel_set_mctrl(struct uart_port *port, u_int mctrl)
> else
> mode |= ATMEL_US_CHMODE_NORMAL;
>
> - UART_PUT_MR(port, mode);
> + atmel_uart_writel(port, ATMEL_US_MR, mode);
> }
>
> /*
> @@ -406,7 +389,7 @@ static u_int atmel_get_mctrl(struct uart_port *port)
> struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
> unsigned int ret = 0, status;
>
> - status = UART_GET_CSR(port);
> + status = atmel_uart_readl(port, ATMEL_US_CSR);
>
> /*
> * The control signals are active low.
> @@ -432,10 +415,10 @@ static void atmel_stop_tx(struct uart_port *port)
>
> if (atmel_use_pdc_tx(port)) {
> /* disable PDC transmit */
> - UART_PUT_PTCR(port, ATMEL_PDC_TXTDIS);
> + atmel_uart_writel(port, ATMEL_PDC_PTCR, ATMEL_PDC_TXTDIS);
> }
> /* Disable interrupts */
> - UART_PUT_IDR(port, atmel_port->tx_done_mask);
> + atmel_uart_writel(port, ATMEL_US_IDR, atmel_port->tx_done_mask);
>
> if ((port->rs485.flags & SER_RS485_ENABLED) &&
> !(port->rs485.flags & SER_RS485_RX_DURING_TX))
> @@ -450,7 +433,7 @@ static void atmel_start_tx(struct uart_port *port)
> struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
>
> if (atmel_use_pdc_tx(port)) {
> - if (UART_GET_PTSR(port) & ATMEL_PDC_TXTEN)
> + if (atmel_uart_readl(port, ATMEL_PDC_PTSR) & ATMEL_PDC_TXTEN)
> /* The transmitter is already running. Yes, we
> really need this.*/
> return;
> @@ -460,10 +443,10 @@ static void atmel_start_tx(struct uart_port *port)
> atmel_stop_rx(port);
>
> /* re-enable PDC transmit */
> - UART_PUT_PTCR(port, ATMEL_PDC_TXTEN);
> + atmel_uart_writel(port, ATMEL_PDC_PTCR, ATMEL_PDC_TXTEN);
> }
> /* Enable interrupts */
> - UART_PUT_IER(port, atmel_port->tx_done_mask);
> + atmel_uart_writel(port, ATMEL_US_IER, atmel_port->tx_done_mask);
> }
>
> /*
> @@ -471,17 +454,19 @@ static void atmel_start_tx(struct uart_port *port)
> */
> static void atmel_start_rx(struct uart_port *port)
> {
> - UART_PUT_CR(port, ATMEL_US_RSTSTA); /* reset status and receiver */
> + /* reset status and receiver */
> + atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_RSTSTA);
>
> - UART_PUT_CR(port, ATMEL_US_RXEN);
> + atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_RXEN);
>
> if (atmel_use_pdc_rx(port)) {
> /* enable PDC controller */
> - UART_PUT_IER(port, ATMEL_US_ENDRX | ATMEL_US_TIMEOUT |
> - port->read_status_mask);
> - UART_PUT_PTCR(port, ATMEL_PDC_RXTEN);
> + atmel_uart_writel(port, ATMEL_US_IER,
> + ATMEL_US_ENDRX | ATMEL_US_TIMEOUT |
> + port->read_status_mask);
> + atmel_uart_writel(port, ATMEL_PDC_PTCR, ATMEL_PDC_RXTEN);
> } else {
> - UART_PUT_IER(port, ATMEL_US_RXRDY);
> + atmel_uart_writel(port, ATMEL_US_IER, ATMEL_US_RXRDY);
> }
> }
>
> @@ -490,15 +475,16 @@ static void atmel_start_rx(struct uart_port *port)
> */
> static void atmel_stop_rx(struct uart_port *port)
> {
> - UART_PUT_CR(port, ATMEL_US_RXDIS);
> + atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_RXDIS);
>
> if (atmel_use_pdc_rx(port)) {
> /* disable PDC receive */
> - UART_PUT_PTCR(port, ATMEL_PDC_RXTDIS);
> - UART_PUT_IDR(port, ATMEL_US_ENDRX | ATMEL_US_TIMEOUT |
> - port->read_status_mask);
> + atmel_uart_writel(port, ATMEL_PDC_PTCR, ATMEL_PDC_RXTDIS);
> + atmel_uart_writel(port, ATMEL_US_IDR,
> + ATMEL_US_ENDRX | ATMEL_US_TIMEOUT |
> + port->read_status_mask);
> } else {
> - UART_PUT_IDR(port, ATMEL_US_RXRDY);
> + atmel_uart_writel(port, ATMEL_US_IDR, ATMEL_US_RXRDY);
> }
> }
>
> @@ -538,7 +524,7 @@ static void atmel_enable_ms(struct uart_port *port)
> else
> ier |= ATMEL_US_DCDIC;
>
> - UART_PUT_IER(port, ier);
> + atmel_uart_writel(port, ATMEL_US_IER, ier);
> }
>
> /*
> @@ -577,7 +563,7 @@ static void atmel_disable_ms(struct uart_port *port)
> else
> idr |= ATMEL_US_DCDIC;
>
> - UART_PUT_IDR(port, idr);
> + atmel_uart_writel(port, ATMEL_US_IDR, idr);
> }
>
> /*
> @@ -586,9 +572,11 @@ static void atmel_disable_ms(struct uart_port *port)
> static void atmel_break_ctl(struct uart_port *port, int break_state)
> {
> if (break_state != 0)
> - UART_PUT_CR(port, ATMEL_US_STTBRK); /* start break */
> + /* start break */
> + atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_STTBRK);
> else
> - UART_PUT_CR(port, ATMEL_US_STPBRK); /* stop break */
> + /* stop break */
> + atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_STPBRK);
> }
>
> /*
> @@ -622,7 +610,7 @@ atmel_buffer_rx_char(struct uart_port *port, unsigned int status,
> static void atmel_pdc_rxerr(struct uart_port *port, unsigned int status)
> {
> /* clear error */
> - UART_PUT_CR(port, ATMEL_US_RSTSTA);
> + atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_RSTSTA);
>
> if (status & ATMEL_US_RXBRK) {
> /* ignore side-effect */
> @@ -645,9 +633,9 @@ static void atmel_rx_chars(struct uart_port *port)
> struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
> unsigned int status, ch;
>
> - status = UART_GET_CSR(port);
> + status = atmel_uart_readl(port, ATMEL_US_CSR);
> while (status & ATMEL_US_RXRDY) {
> - ch = UART_GET_CHAR(port);
> + ch = atmel_uart_readl(port, ATMEL_US_RHR);
>
> /*
> * note that the error handling code is
> @@ -658,12 +646,13 @@ static void atmel_rx_chars(struct uart_port *port)
> || atmel_port->break_active)) {
>
> /* clear error */
> - UART_PUT_CR(port, ATMEL_US_RSTSTA);
> + atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_RSTSTA);
>
> if (status & ATMEL_US_RXBRK
> && !atmel_port->break_active) {
> atmel_port->break_active = 1;
> - UART_PUT_IER(port, ATMEL_US_RXBRK);
> + atmel_uart_writel(port, ATMEL_US_IER,
> + ATMEL_US_RXBRK);
> } else {
> /*
> * This is either the end-of-break
> @@ -672,14 +661,15 @@ static void atmel_rx_chars(struct uart_port *port)
> * being set. In both cases, the next
> * RXBRK will indicate start-of-break.
> */
> - UART_PUT_IDR(port, ATMEL_US_RXBRK);
> + atmel_uart_writel(port, ATMEL_US_IDR,
> + ATMEL_US_RXBRK);
> status &= ~ATMEL_US_RXBRK;
> atmel_port->break_active = 0;
> }
> }
>
> atmel_buffer_rx_char(port, status, ch);
> - status = UART_GET_CSR(port);
> + status = atmel_uart_readl(port, ATMEL_US_CSR);
> }
>
> tasklet_schedule(&atmel_port->tasklet);
> @@ -694,16 +684,18 @@ static void atmel_tx_chars(struct uart_port *port)
> struct circ_buf *xmit = &port->state->xmit;
> struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
>
> - if (port->x_char && UART_GET_CSR(port) & atmel_port->tx_done_mask) {
> - UART_PUT_CHAR(port, port->x_char);
> + if (port->x_char &&
> + (atmel_uart_readl(port, ATMEL_US_CSR) & atmel_port->tx_done_mask)) {
> + atmel_uart_writel(port, ATMEL_US_THR, port->x_char);
> port->icount.tx++;
> port->x_char = 0;
> }
> if (uart_circ_empty(xmit) || uart_tx_stopped(port))
> return;
>
> - while (UART_GET_CSR(port) & atmel_port->tx_done_mask) {
> - UART_PUT_CHAR(port, xmit->buf[xmit->tail]);
> + while (atmel_uart_readl(port, ATMEL_US_CSR) &
> + atmel_port->tx_done_mask) {
> + atmel_uart_writel(port, ATMEL_US_THR, xmit->buf[xmit->tail]);
> xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1);
> port->icount.tx++;
> if (uart_circ_empty(xmit))
> @@ -715,7 +707,8 @@ static void atmel_tx_chars(struct uart_port *port)
>
> if (!uart_circ_empty(xmit))
> /* Enable interrupts */
> - UART_PUT_IER(port, atmel_port->tx_done_mask);
> + atmel_uart_writel(port, ATMEL_US_IER,
> + atmel_port->tx_done_mask);
> }
>
> static void atmel_complete_tx_dma(void *arg)
> @@ -935,14 +928,14 @@ static void atmel_rx_from_dma(struct uart_port *port)
>
>
> /* Reset the UART timeout early so that we don't miss one */
> - UART_PUT_CR(port, ATMEL_US_STTTO);
> + atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_STTTO);
> dmastat = dmaengine_tx_status(chan,
> atmel_port->cookie_rx,
> &state);
> /* Restart a new tasklet if DMA status is error */
> if (dmastat == DMA_ERROR) {
> dev_dbg(port->dev, "Get residue error, restart tasklet\n");
> - UART_PUT_IER(port, ATMEL_US_TIMEOUT);
> + atmel_uart_writel(port, ATMEL_US_IER, ATMEL_US_TIMEOUT);
> tasklet_schedule(&atmel_port->tasklet);
> return;
> }
> @@ -1008,7 +1001,7 @@ static void atmel_rx_from_dma(struct uart_port *port)
> tty_flip_buffer_push(tport);
> spin_lock(&port->lock);
>
> - UART_PUT_IER(port, ATMEL_US_TIMEOUT);
> + atmel_uart_writel(port, ATMEL_US_IER, ATMEL_US_TIMEOUT);
> }
>
> static int atmel_prepare_rx_dma(struct uart_port *port)
> @@ -1118,8 +1111,8 @@ atmel_handle_receive(struct uart_port *port, unsigned int pending)
> * the moment.
> */
> if (pending & (ATMEL_US_ENDRX | ATMEL_US_TIMEOUT)) {
> - UART_PUT_IDR(port, (ATMEL_US_ENDRX
> - | ATMEL_US_TIMEOUT));
> + atmel_uart_writel(port, ATMEL_US_IDR,
> + (ATMEL_US_ENDRX | ATMEL_US_TIMEOUT));
> tasklet_schedule(&atmel_port->tasklet);
> }
>
> @@ -1130,7 +1123,8 @@ atmel_handle_receive(struct uart_port *port, unsigned int pending)
>
> if (atmel_use_dma_rx(port)) {
> if (pending & ATMEL_US_TIMEOUT) {
> - UART_PUT_IDR(port, ATMEL_US_TIMEOUT);
> + atmel_uart_writel(port, ATMEL_US_IDR,
> + ATMEL_US_TIMEOUT);
> tasklet_schedule(&atmel_port->tasklet);
> }
> }
> @@ -1143,8 +1137,8 @@ atmel_handle_receive(struct uart_port *port, unsigned int pending)
> * End of break detected. If it came along with a
> * character, atmel_rx_chars will handle it.
> */
> - UART_PUT_CR(port, ATMEL_US_RSTSTA);
> - UART_PUT_IDR(port, ATMEL_US_RXBRK);
> + atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_RSTSTA);
> + atmel_uart_writel(port, ATMEL_US_IDR, ATMEL_US_RXBRK);
> atmel_port->break_active = 0;
> }
> }
> @@ -1159,7 +1153,8 @@ atmel_handle_transmit(struct uart_port *port, unsigned int pending)
>
> if (pending & atmel_port->tx_done_mask) {
> /* Either PDC or interrupt transmission */
> - UART_PUT_IDR(port, atmel_port->tx_done_mask);
> + atmel_uart_writel(port, ATMEL_US_IDR,
> + atmel_port->tx_done_mask);
> tasklet_schedule(&atmel_port->tasklet);
> }
> }
> @@ -1197,7 +1192,7 @@ static irqreturn_t atmel_interrupt(int irq, void *dev_id)
>
> do {
> status = atmel_get_lines_status(port);
> - mask = UART_GET_IMR(port);
> + mask = atmel_uart_readl(port, ATMEL_US_IMR);
> pending = status & mask;
> if (!gpio_handled) {
> /*
> @@ -1223,7 +1218,7 @@ static irqreturn_t atmel_interrupt(int irq, void *dev_id)
> if (atmel_port->suspended) {
> atmel_port->pending |= pending;
> atmel_port->pending_status = status;
> - UART_PUT_IDR(port, mask);
> + atmel_uart_writel(port, ATMEL_US_IDR, mask);
> pm_system_wakeup();
> break;
> }
> @@ -1260,7 +1255,7 @@ static void atmel_tx_pdc(struct uart_port *port)
> int count;
>
> /* nothing left to transmit? */
> - if (UART_GET_TCR(port))
> + if (atmel_uart_readl(port, ATMEL_PDC_TCR))
> return;
>
> xmit->tail += pdc->ofs;
> @@ -1272,7 +1267,7 @@ static void atmel_tx_pdc(struct uart_port *port)
> /* more to transmit - setup next transfer */
>
> /* disable PDC transmit */
> - UART_PUT_PTCR(port, ATMEL_PDC_TXTDIS);
> + atmel_uart_writel(port, ATMEL_PDC_PTCR, ATMEL_PDC_TXTDIS);
>
> if (!uart_circ_empty(xmit) && !uart_tx_stopped(port)) {
> dma_sync_single_for_device(port->dev,
> @@ -1283,12 +1278,14 @@ static void atmel_tx_pdc(struct uart_port *port)
> count = CIRC_CNT_TO_END(xmit->head, xmit->tail, UART_XMIT_SIZE);
> pdc->ofs = count;
>
> - UART_PUT_TPR(port, pdc->dma_addr + xmit->tail);
> - UART_PUT_TCR(port, count);
> + atmel_uart_writel(port, ATMEL_PDC_TPR,
> + pdc->dma_addr + xmit->tail);
> + atmel_uart_writel(port, ATMEL_PDC_TCR, count);
> /* re-enable PDC transmit */
> - UART_PUT_PTCR(port, ATMEL_PDC_TXTEN);
> + atmel_uart_writel(port, ATMEL_PDC_PTCR, ATMEL_PDC_TXTEN);
> /* Enable interrupts */
> - UART_PUT_IER(port, atmel_port->tx_done_mask);
> + atmel_uart_writel(port, ATMEL_US_IER,
> + atmel_port->tx_done_mask);
> } else {
> if ((port->rs485.flags & SER_RS485_ENABLED) &&
> !(port->rs485.flags & SER_RS485_RX_DURING_TX)) {
> @@ -1414,10 +1411,10 @@ static void atmel_rx_from_pdc(struct uart_port *port)
>
> do {
> /* Reset the UART timeout early so that we don't miss one */
> - UART_PUT_CR(port, ATMEL_US_STTTO);
> + atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_STTTO);
>
> pdc = &atmel_port->pdc_rx[rx_idx];
> - head = UART_GET_RPR(port) - pdc->dma_addr;
> + head = atmel_uart_readl(port, ATMEL_PDC_RPR) - pdc->dma_addr;
> tail = pdc->ofs;
>
> /* If the PDC has switched buffers, RPR won't contain
> @@ -1460,8 +1457,8 @@ static void atmel_rx_from_pdc(struct uart_port *port)
> */
> if (head >= pdc->dma_size) {
> pdc->ofs = 0;
> - UART_PUT_RNPR(port, pdc->dma_addr);
> - UART_PUT_RNCR(port, pdc->dma_size);
> + atmel_uart_writel(port, ATMEL_PDC_RNPR, pdc->dma_addr);
> + atmel_uart_writel(port, ATMEL_PDC_RNCR, pdc->dma_size);
>
> rx_idx = !rx_idx;
> atmel_port->pdc_rx_idx = rx_idx;
> @@ -1476,7 +1473,8 @@ static void atmel_rx_from_pdc(struct uart_port *port)
> tty_flip_buffer_push(tport);
> spin_lock(&port->lock);
>
> - UART_PUT_IER(port, ATMEL_US_ENDRX | ATMEL_US_TIMEOUT);
> + atmel_uart_writel(port, ATMEL_US_IER,
> + ATMEL_US_ENDRX | ATMEL_US_TIMEOUT);
> }
>
> static int atmel_prepare_rx_pdc(struct uart_port *port)
> @@ -1509,11 +1507,12 @@ static int atmel_prepare_rx_pdc(struct uart_port *port)
>
> atmel_port->pdc_rx_idx = 0;
>
> - UART_PUT_RPR(port, atmel_port->pdc_rx[0].dma_addr);
> - UART_PUT_RCR(port, PDC_BUFFER_SIZE);
> + atmel_uart_writel(port, ATMEL_PDC_RPR, atmel_port->pdc_rx[0].dma_addr);
> + atmel_uart_writel(port, ATMEL_PDC_RCR, PDC_BUFFER_SIZE);
>
> - UART_PUT_RNPR(port, atmel_port->pdc_rx[1].dma_addr);
> - UART_PUT_RNCR(port, PDC_BUFFER_SIZE);
> + atmel_uart_writel(port, ATMEL_PDC_RNPR,
> + atmel_port->pdc_rx[1].dma_addr);
> + atmel_uart_writel(port, ATMEL_PDC_RNCR, PDC_BUFFER_SIZE);
>
> return 0;
> }
> @@ -1667,7 +1666,7 @@ static void atmel_set_ops(struct uart_port *port)
> static void atmel_get_ip_name(struct uart_port *port)
> {
> struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
> - int name = UART_GET_IP_NAME(port);
> + int name = atmel_uart_readl(port, ATMEL_US_NAME);
> u32 version;
> int usart, uart;
> /* usart and uart ascii */
> @@ -1684,7 +1683,7 @@ static void atmel_get_ip_name(struct uart_port *port)
> atmel_port->is_usart = false;
> } else {
> /* fallback for older SoCs: use version field */
> - version = UART_GET_IP_VERSION(port);
> + version = atmel_uart_readl(port, ATMEL_US_VERSION);
> switch (version) {
> case 0x302:
> case 0x10213:
> @@ -1756,7 +1755,7 @@ static int atmel_startup(struct uart_port *port)
> * request_irq() is called we could get stuck trying to
> * handle an unexpected interrupt
> */
> - UART_PUT_IDR(port, -1);
> + atmel_uart_writel(port, ATMEL_US_IDR, -1);
> atmel_port->ms_irq_enabled = false;
>
> /*
> @@ -1804,9 +1803,9 @@ static int atmel_startup(struct uart_port *port)
> /*
> * Finally, enable the serial port
> */
> - UART_PUT_CR(port, ATMEL_US_RSTSTA | ATMEL_US_RSTRX);
> + atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_RSTSTA | ATMEL_US_RSTRX);
> /* enable xmit & rcvr */
> - UART_PUT_CR(port, ATMEL_US_TXEN | ATMEL_US_RXEN);
> + atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_TXEN | ATMEL_US_RXEN);
>
> setup_timer(&atmel_port->uart_timer,
> atmel_uart_timer_callback,
> @@ -1819,13 +1818,14 @@ static int atmel_startup(struct uart_port *port)
> jiffies + uart_poll_timeout(port));
> /* set USART timeout */
> } else {
> - UART_PUT_RTOR(port, PDC_RX_TIMEOUT);
> - UART_PUT_CR(port, ATMEL_US_STTTO);
> + atmel_uart_writel(port, ATMEL_US_RTOR, PDC_RX_TIMEOUT);
> + atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_STTTO);
>
> - UART_PUT_IER(port, ATMEL_US_ENDRX | ATMEL_US_TIMEOUT);
> + atmel_uart_writel(port, ATMEL_US_IER,
> + ATMEL_US_ENDRX | ATMEL_US_TIMEOUT);
> }
> /* enable PDC controller */
> - UART_PUT_PTCR(port, ATMEL_PDC_RXTEN);
> + atmel_uart_writel(port, ATMEL_PDC_PTCR, ATMEL_PDC_RXTEN);
> } else if (atmel_use_dma_rx(port)) {
> /* set UART timeout */
> if (!atmel_port->is_usart) {
> @@ -1833,14 +1833,15 @@ static int atmel_startup(struct uart_port *port)
> jiffies + uart_poll_timeout(port));
> /* set USART timeout */
> } else {
> - UART_PUT_RTOR(port, PDC_RX_TIMEOUT);
> - UART_PUT_CR(port, ATMEL_US_STTTO);
> + atmel_uart_writel(port, ATMEL_US_RTOR, PDC_RX_TIMEOUT);
> + atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_STTTO);
>
> - UART_PUT_IER(port, ATMEL_US_TIMEOUT);
> + atmel_uart_writel(port, ATMEL_US_IER,
> + ATMEL_US_TIMEOUT);
> }
> } else {
> /* enable receive only */
> - UART_PUT_IER(port, ATMEL_US_RXRDY);
> + atmel_uart_writel(port, ATMEL_US_IER, ATMEL_US_RXRDY);
> }
>
> return 0;
> @@ -1860,7 +1861,7 @@ static void atmel_flush_buffer(struct uart_port *port)
> struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
>
> if (atmel_use_pdc_tx(port)) {
> - UART_PUT_TCR(port, 0);
> + atmel_uart_writel(port, ATMEL_PDC_TCR, 0);
> atmel_port->pdc_tx.ofs = 0;
> }
> }
> @@ -1892,8 +1893,8 @@ static void atmel_shutdown(struct uart_port *port)
> atmel_stop_rx(port);
> atmel_stop_tx(port);
>
> - UART_PUT_CR(port, ATMEL_US_RSTSTA);
> - UART_PUT_IDR(port, -1);
> + atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_RSTSTA);
> + atmel_uart_writel(port, ATMEL_US_IDR, -1);
>
>
> /*
> @@ -1938,12 +1939,12 @@ static void atmel_serial_pm(struct uart_port *port, unsigned int state,
> clk_prepare_enable(atmel_port->clk);
>
> /* re-enable interrupts if we disabled some on suspend */
> - UART_PUT_IER(port, atmel_port->backup_imr);
> + atmel_uart_writel(port, ATMEL_US_IER, atmel_port->backup_imr);
> break;
> case 3:
> /* Back up the interrupt mask and disable all interrupts */
> - atmel_port->backup_imr = UART_GET_IMR(port);
> - UART_PUT_IDR(port, -1);
> + atmel_port->backup_imr = atmel_uart_readl(port, ATMEL_US_IMR);
> + atmel_uart_writel(port, ATMEL_US_IDR, -1);
>
> /*
> * Disable the peripheral clock for this serial port.
> @@ -1966,7 +1967,7 @@ static void atmel_set_termios(struct uart_port *port, struct ktermios *termios,
> unsigned int old_mode, mode, imr, quot, baud;
>
> /* save the current mode register */
> - mode = old_mode = UART_GET_MR(port);
> + mode = old_mode = atmel_uart_readl(port, ATMEL_US_MR);
>
> /* reset the mode, clock divisor, parity, stop bits and data size */
> mode &= ~(ATMEL_US_USCLKS | ATMEL_US_CHRL | ATMEL_US_NBSTOP |
> @@ -2025,7 +2026,7 @@ static void atmel_set_termios(struct uart_port *port, struct ktermios *termios,
>
> if (atmel_use_pdc_rx(port))
> /* need to enable error interrupts */
> - UART_PUT_IER(port, port->read_status_mask);
> + atmel_uart_writel(port, ATMEL_US_IER, port->read_status_mask);
>
> /*
> * Characters to ignore
> @@ -2052,15 +2053,16 @@ static void atmel_set_termios(struct uart_port *port, struct ktermios *termios,
> * transmitter is empty if requested by the caller, so there's
> * no need to wait for it here.
> */
> - imr = UART_GET_IMR(port);
> - UART_PUT_IDR(port, -1);
> + imr = atmel_uart_readl(port, ATMEL_US_IMR);
> + atmel_uart_writel(port, ATMEL_US_IDR, -1);
>
> /* disable receiver and transmitter */
> - UART_PUT_CR(port, ATMEL_US_TXDIS | ATMEL_US_RXDIS);
> + atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_TXDIS | ATMEL_US_RXDIS);
>
> /* mode */
> if (port->rs485.flags & SER_RS485_ENABLED) {
> - UART_PUT_TTGR(port, port->rs485.delay_rts_after_send);
> + atmel_uart_writel(port, ATMEL_US_TTGR,
> + port->rs485.delay_rts_after_send);
> mode |= ATMEL_US_USMODE_RS485;
> } else if (termios->c_cflag & CRTSCTS) {
> /* RS232 with hardware handshake (RTS/CTS) */
> @@ -2071,7 +2073,7 @@ static void atmel_set_termios(struct uart_port *port, struct ktermios *termios,
> }
>
> /* set the mode, clock divisor, parity, stop bits and data size */
> - UART_PUT_MR(port, mode);
> + atmel_uart_writel(port, ATMEL_US_MR, mode);
>
> /*
> * when switching the mode, set the RTS line state according to the
> @@ -2088,16 +2090,16 @@ static void atmel_set_termios(struct uart_port *port, struct ktermios *termios,
> rts_state = ATMEL_US_RTSEN;
> }
>
> - UART_PUT_CR(port, rts_state);
> + atmel_uart_writel(port, ATMEL_US_CR, rts_state);
> }
>
> /* set the baud rate */
> - UART_PUT_BRGR(port, quot);
> - UART_PUT_CR(port, ATMEL_US_RSTSTA | ATMEL_US_RSTRX);
> - UART_PUT_CR(port, ATMEL_US_TXEN | ATMEL_US_RXEN);
> + atmel_uart_writel(port, ATMEL_US_BRGR, quot);
> + atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_RSTSTA | ATMEL_US_RSTRX);
> + atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_TXEN | ATMEL_US_RXEN);
>
> /* restore interrupts */
> - UART_PUT_IER(port, imr);
> + atmel_uart_writel(port, ATMEL_US_IER, imr);
>
> /* CTS flow-control and modem-status interrupts */
> if (UART_ENABLE_MS(port, termios->c_cflag))
> @@ -2208,18 +2210,18 @@ static int atmel_verify_port(struct uart_port *port, struct serial_struct *ser)
> #ifdef CONFIG_CONSOLE_POLL
> static int atmel_poll_get_char(struct uart_port *port)
> {
> - while (!(UART_GET_CSR(port) & ATMEL_US_RXRDY))
> + while (!(atmel_uart_readl(port, ATMEL_US_CSR) & ATMEL_US_RXRDY))
> cpu_relax();
>
> - return UART_GET_CHAR(port);
> + return atmel_uart_readl(port, ATMEL_US_RHR);
> }
>
> static void atmel_poll_put_char(struct uart_port *port, unsigned char ch)
> {
> - while (!(UART_GET_CSR(port) & ATMEL_US_TXRDY))
> + while (!(atmel_uart_readl(port, ATMEL_US_CSR) & ATMEL_US_TXRDY))
> cpu_relax();
>
> - UART_PUT_CHAR(port, ch);
> + atmel_uart_writel(port, ATMEL_US_THR, ch);
> }
> #endif
>
> @@ -2324,9 +2326,9 @@ struct platform_device *atmel_default_console_device; /* the serial console devi
> #ifdef CONFIG_SERIAL_ATMEL_CONSOLE
> static void atmel_console_putchar(struct uart_port *port, int ch)
> {
> - while (!(UART_GET_CSR(port) & ATMEL_US_TXRDY))
> + while (!(atmel_uart_readl(port, ATMEL_US_CSR) & ATMEL_US_TXRDY))
> cpu_relax();
> - UART_PUT_CHAR(port, ch);
> + atmel_uart_writel(port, ATMEL_US_THR, ch);
> }
>
> /*
> @@ -2342,12 +2344,13 @@ static void atmel_console_write(struct console *co, const char *s, u_int count)
> /*
> * First, save IMR and then disable interrupts
> */
> - imr = UART_GET_IMR(port);
> - UART_PUT_IDR(port, ATMEL_US_RXRDY | atmel_port->tx_done_mask);
> + imr = atmel_uart_readl(port, ATMEL_US_IMR);
> + atmel_uart_writel(port, ATMEL_US_IDR,
> + ATMEL_US_RXRDY | atmel_port->tx_done_mask);
>
> /* Store PDC transmit status and disable it */
> - pdc_tx = UART_GET_PTSR(port) & ATMEL_PDC_TXTEN;
> - UART_PUT_PTCR(port, ATMEL_PDC_TXTDIS);
> + pdc_tx = atmel_uart_readl(port, ATMEL_PDC_PTSR) & ATMEL_PDC_TXTEN;
> + atmel_uart_writel(port, ATMEL_PDC_PTCR, ATMEL_PDC_TXTDIS);
>
> uart_console_write(port, s, count, atmel_console_putchar);
>
> @@ -2356,15 +2359,15 @@ static void atmel_console_write(struct console *co, const char *s, u_int count)
> * and restore IMR
> */
> do {
> - status = UART_GET_CSR(port);
> + status = atmel_uart_readl(port, ATMEL_US_CSR);
> } while (!(status & ATMEL_US_TXRDY));
>
> /* Restore PDC transmit status */
> if (pdc_tx)
> - UART_PUT_PTCR(port, ATMEL_PDC_TXTEN);
> + atmel_uart_writel(port, ATMEL_PDC_PTCR, ATMEL_PDC_TXTEN);
>
> /* set interrupts back the way they were */
> - UART_PUT_IER(port, imr);
> + atmel_uart_writel(port, ATMEL_US_IER, imr);
> }
>
> /*
> @@ -2380,17 +2383,17 @@ static void __init atmel_console_get_options(struct uart_port *port, int *baud,
> * If the baud rate generator isn't running, the port wasn't
> * initialized by the boot loader.
> */
> - quot = UART_GET_BRGR(port) & ATMEL_US_CD;
> + quot = atmel_uart_readl(port, ATMEL_US_BRGR) & ATMEL_US_CD;
> if (!quot)
> return;
>
> - mr = UART_GET_MR(port) & ATMEL_US_CHRL;
> + mr = atmel_uart_readl(port, ATMEL_US_MR) & ATMEL_US_CHRL;
> if (mr == ATMEL_US_CHRL_8)
> *bits = 8;
> else
> *bits = 7;
>
> - mr = UART_GET_MR(port) & ATMEL_US_PAR;
> + mr = atmel_uart_readl(port, ATMEL_US_MR) & ATMEL_US_PAR;
> if (mr == ATMEL_US_PAR_EVEN)
> *parity = 'e';
> else if (mr == ATMEL_US_PAR_ODD)
> @@ -2423,9 +2426,9 @@ static int __init atmel_console_setup(struct console *co, char *options)
> if (ret)
> return ret;
>
> - UART_PUT_IDR(port, -1);
> - UART_PUT_CR(port, ATMEL_US_RSTSTA | ATMEL_US_RSTRX);
> - UART_PUT_CR(port, ATMEL_US_TXEN | ATMEL_US_RXEN);
> + atmel_uart_writel(port, ATMEL_US_IDR, -1);
> + atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_RSTSTA | ATMEL_US_RSTRX);
> + atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_TXEN | ATMEL_US_RXEN);
>
> if (options)
> uart_parse_options(options, &baud, &parity, &bits, &flow);
> @@ -2532,7 +2535,8 @@ static int atmel_serial_suspend(struct platform_device *pdev,
>
> if (atmel_is_console_port(port) && console_suspend_enabled) {
> /* Drain the TX shifter */
> - while (!(UART_GET_CSR(port) & ATMEL_US_TXEMPTY))
> + while (!(atmel_uart_readl(port, ATMEL_US_CSR) &
> + ATMEL_US_TXEMPTY))
> cpu_relax();
> }
>
> @@ -2684,8 +2688,9 @@ static int atmel_serial_probe(struct platform_device *pdev)
> clk_prepare_enable(port->clk);
>
> if (rs485_enabled) {
> - UART_PUT_MR(&port->uart, ATMEL_US_USMODE_NORMAL);
> - UART_PUT_CR(&port->uart, ATMEL_US_RTSEN);
> + atmel_uart_writel(&port->uart, ATMEL_US_MR,
> + ATMEL_US_USMODE_NORMAL);
> + atmel_uart_writel(&port->uart, ATMEL_US_CR, ATMEL_US_RTSEN);
> }
>
> /*
>
--
Nicolas Ferre
More information about the linux-arm-kernel
mailing list