[PATCH 4/4] doc: dt: dma: add bindings for lpc1850-dmamux
Joachim Eastwood
manabian at gmail.com
Sat Jul 11 05:12:07 PDT 2015
Add device tree bindings documentation for the
lpc1850-dmamux DMA router.
Signed-off-by: Joachim Eastwood <manabian at gmail.com>
---
.../devicetree/bindings/dma/lpc1850-dmamux.txt | 54 ++++++++++++++++++++++
1 file changed, 54 insertions(+)
create mode 100644 Documentation/devicetree/bindings/dma/lpc1850-dmamux.txt
diff --git a/Documentation/devicetree/bindings/dma/lpc1850-dmamux.txt b/Documentation/devicetree/bindings/dma/lpc1850-dmamux.txt
new file mode 100644
index 000000000000..87740adb2995
--- /dev/null
+++ b/Documentation/devicetree/bindings/dma/lpc1850-dmamux.txt
@@ -0,0 +1,54 @@
+NXP LPC18xx/43xx DMA MUX (DMA request router)
+
+Required properties:
+- compatible: "nxp,lpc1850-dmamux"
+- reg: Memory map for accessing module
+- #dma-cells: Should be set to <3>.
+ * 1st cell contain the master dma request signal
+ * 2nd cell contain the mux value (0-3) for the peripheral
+ * 3rd cell contain either 1 or 2 depending on the AHB
+ master used.
+- dma-requests: Number of DMA requests for the mux
+- dma-masters: phandle pointing to the DMA controller
+
+The DMA controller node need to have the following poroperties:
+- dma-requests: Number of DMA requests the controller can handle
+
+Example:
+
+dmac: dma at 40002000 {
+ compatible = "nxp,lpc1850-gpdma", "arm,pl080", "arm,primecell";
+ arm,primecell-periphid = <0x00041080>;
+ reg = <0x40002000 0x1000>;
+ interrupts = <2>;
+ clocks = <&ccu1 CLK_CPU_DMA>;
+ clock-names = "apb_pclk";
+ #dma-cells = <2>;
+ dma-channels = <8>;
+ dma-requests = <16>;
+ lli-bus-interface-ahb1;
+ lli-bus-interface-ahb2;
+ mem-bus-interface-ahb1;
+ mem-bus-interface-ahb2;
+ memcpy-burst-size = <256>;
+ memcpy-bus-width = <32>;
+};
+
+dmamux: dma-mux {
+ compatible = "nxp,lpc1850-dmamux";
+ #dma-cells = <3>;
+ dma-requests = <64>;
+ dma-masters = <&dmac>;
+};
+
+uart0: serial at 40081000 {
+ compatible = "nxp,lpc1850-uart", "ns16550a";
+ reg = <0x40081000 0x1000>;
+ reg-shift = <2>;
+ interrupts = <24>;
+ clocks = <&ccu2 CLK_APB0_UART0>, <&ccu1 CLK_CPU_UART0>;
+ clock-names = "uartclk", "reg";
+ dmas = <&dmamux 1 1 2
+ &dmamux 2 1 2>;
+ dma-names = "tx", "rx";
+};
--
1.8.0
More information about the linux-arm-kernel
mailing list