[PATCH 6/8] ARM: dts: imx: add imx6ul and imx6ul evk board support

Shawn Guo shawnguo at kernel.org
Thu Jul 9 00:02:07 PDT 2015


On Wed, Jun 17, 2015 at 11:39:27PM +0800, Frank.Li at freescale.com wrote:
> From: Frank Li <Frank.Li at freescale.com>
> 
> Add new SOC i.MX6UL dtb file support, including evk board
> support
> 
> i.MX6 Ultralite processor include one ARM cortext-A7 core.
> Offer high perfomance and lowest power consumption.
> 
> Main included:
> - 4 MMC/SD/SDIO
> - 2 USB 2.0 OTG
> - 3 I2S/SAI/AC97
> - 4 eCSPI
> - 4 I2C
> - 2 ENET
> - 2 CAN
> - 3 wdog
> - ASRC
> - 8 uart
> - LCDIF
> - PXP
> 
> Signed-off-by: Anson Huang <b20788 at freescale.com>
> Signed-off-by: Fugang Duan <B38611 at freescale.com>
> Signed-off-by: Fancy Fang <chen.fang at freescale.com>
> Signed-off-by: Frank Li <Frank.Li at freescale.com>
> ---
>  arch/arm/boot/dts/Makefile             |   2 +
>  arch/arm/boot/dts/imx6ul-14x14-evk.dts | 337 +++++++++++++++++
>  arch/arm/boot/dts/imx6ul.dtsi          | 645 +++++++++++++++++++++++++++++++++
>  3 files changed, 984 insertions(+)
>  create mode 100644 arch/arm/boot/dts/imx6ul-14x14-evk.dts
>  create mode 100644 arch/arm/boot/dts/imx6ul.dtsi
> 
> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> index 246473a..7c2fd63 100644
> --- a/arch/arm/boot/dts/Makefile
> +++ b/arch/arm/boot/dts/Makefile
> @@ -331,6 +331,8 @@ dtb-$(CONFIG_SOC_IMX6SX) += \
>  	imx6sx-sabreauto.dtb \
>  	imx6sx-sdb-reva.dtb \
>  	imx6sx-sdb.dtb
> +dtb-$(CONFIG_SOC_IMX6UL) += \
> +	imx6ul-14x14-evk.dtb
>  dtb-$(CONFIG_SOC_IMX7D) += \
>  	imx7d-sdb.dtb
>  dtb-$(CONFIG_SOC_LS1021A) += \
> diff --git a/arch/arm/boot/dts/imx6ul-14x14-evk.dts b/arch/arm/boot/dts/imx6ul-14x14-evk.dts
> new file mode 100644
> index 0000000..449b5d3
> --- /dev/null
> +++ b/arch/arm/boot/dts/imx6ul-14x14-evk.dts
> @@ -0,0 +1,337 @@
> +/*
> + * Copyright (C) 2015 Freescale Semiconductor, Inc.
> + *
> + * This program is free software; you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License version 2 as
> + * published by the Free Software Foundation.
> + */
> +
> +/dts-v1/;
> +
> +#include <dt-bindings/input/input.h>
> +#include "imx6ul.dtsi"
> +
> +/ {
> +	model = "Freescale i.MX6 UltraLite 14x14 EVK Board";
> +	compatible = "fsl,imx6ul-14x14-evk", "fsl,imx6ul";
> +
> +	chosen {
> +		stdout-path = &uart1;
> +	};
> +
> +	memory {
> +		reg = <0x80000000 0x20000000>;
> +	};
> +
> +	regulators {
> +		compatible = "simple-bus";
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +
> +		reg_sd1_vmmc: regulator at 1 {

There should be a 'reg' property when unit-address is coded in node
name.  Also, the numbering starts from 0.

> +			compatible = "regulator-fixed";
> +			regulator-name = "VSD_3V3";
> +			regulator-min-microvolt = <3300000>;
> +			regulator-max-microvolt = <3300000>;
> +			gpio = <&gpio1 9 GPIO_ACTIVE_HIGH>;
> +			enable-active-high;
> +		};
> +	};
> +};
> +
> +&cpu0 {
> +	arm-supply = <&reg_arm>;
> +	soc-supply = <&reg_soc>;

These two can be the default cases to be put in the <soc>.dtsi, and for
the boards with board level supply design, their <board>.dts can
overwrite.

> +};
> +
> +&uart1 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_uart1>;
> +	status = "okay";
> +};
> +
> +&uart2 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_uart2>;
> +	fsl,uart-has-rtscts;
> +	/* for DTE mode, add below change */
> +	/* fsl,dte-mode; */
> +	/* pinctrl-0 = <&pinctrl_uart2dte>; */

For given board design, whether DTE mode is supported should be
determined.  Why these commenting?

> +	status = "okay";
> +};
> +
> +&usdhc1 {
> +	pinctrl-names = "default", "state_100mhz", "state_200mhz";
> +	pinctrl-0 = <&pinctrl_usdhc1>;
> +	pinctrl-1 = <&pinctrl_usdhc1_100mhz>;
> +	pinctrl-2 = <&pinctrl_usdhc1_200mhz>;
> +	cd-gpios = <&gpio1 19 0>;
> +	keep-power-in-suspend;
> +	enable-sdio-wakeup;
> +	vmmc-supply = <&reg_sd1_vmmc>;
> +	status = "okay";
> +};
> +
> +&usdhc2 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_usdhc2>;
> +	no-1-8-v;
> +	keep-power-in-suspend;
> +	enable-sdio-wakeup;
> +	status = "okay";
> +};
> +
> +&iomuxc {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_hog_1>;

Have new line between property list and sub-nodes.

> +	imx6ul-evk {
> +		pinctrl_hog_1: hoggrp-1 {

The suffix "1" makes no sense.  Drop it.

> +			fsl,pins = <
> +				MX6UL_PAD_LCD_RESET__WDOG1_WDOG_ANY    0x30b0

Should be in the wdog pinctrl?

> +				MX6UL_PAD_UART1_RTS_B__GPIO1_IO19	0x17059 /* SD1 CD */
> +				MX6UL_PAD_GPIO1_IO05__USDHC1_VSELECT	0x17059 /* SD1 VSELECT */
> +				MX6UL_PAD_GPIO1_IO09__GPIO1_IO09        0x17059 /* SD1 RESET */

Should be in the SD1 pinctrl group?

> +			>;
> +		};
> +
> +		pinctrl_csi1: csi1grp {
> +			fsl,pins = <
> +				MX6UL_PAD_CSI_MCLK__CSI_MCLK		0x1b088
> +				MX6UL_PAD_CSI_PIXCLK__CSI_PIXCLK	0x1b088
> +				MX6UL_PAD_CSI_VSYNC__CSI_VSYNC		0x1b088
> +				MX6UL_PAD_CSI_HSYNC__CSI_HSYNC		0x1b088
> +				MX6UL_PAD_CSI_DATA00__CSI_DATA02	0x1b088
> +				MX6UL_PAD_CSI_DATA01__CSI_DATA03	0x1b088
> +				MX6UL_PAD_CSI_DATA02__CSI_DATA04	0x1b088
> +				MX6UL_PAD_CSI_DATA03__CSI_DATA05	0x1b088
> +				MX6UL_PAD_CSI_DATA04__CSI_DATA06	0x1b088
> +				MX6UL_PAD_CSI_DATA05__CSI_DATA07	0x1b088
> +				MX6UL_PAD_CSI_DATA06__CSI_DATA08	0x1b088
> +				MX6UL_PAD_CSI_DATA07__CSI_DATA09	0x1b088
> +			>;
> +		};
> +
> +		pinctrl_enet1: enet1grp {
> +			fsl,pins = <
> +				MX6UL_PAD_ENET1_RX_EN__ENET1_RX_EN	0x1b0b0
> +				MX6UL_PAD_ENET1_RX_ER__ENET1_RX_ER	0x1b0b0
> +				MX6UL_PAD_ENET1_RX_DATA0__ENET1_RDATA00	0x1b0b0
> +				MX6UL_PAD_ENET1_RX_DATA1__ENET1_RDATA01	0x1b0b0
> +				MX6UL_PAD_ENET1_TX_EN__ENET1_TX_EN	0x1b0b0
> +				MX6UL_PAD_ENET1_TX_DATA0__ENET1_TDATA00	0x1b0b0
> +				MX6UL_PAD_ENET1_TX_DATA1__ENET1_TDATA01	0x1b0b0
> +				MX6UL_PAD_ENET1_TX_CLK__ENET1_REF_CLK1	0x4001b031
> +			>;
> +		};
> +
> +		pinctrl_enet2: enet2grp {
> +			fsl,pins = <
> +				MX6UL_PAD_GPIO1_IO07__ENET2_MDC		0x1b0b0
> +				MX6UL_PAD_GPIO1_IO06__ENET2_MDIO	0x1b0b0
> +				MX6UL_PAD_ENET2_RX_EN__ENET2_RX_EN	0x1b0b0
> +				MX6UL_PAD_ENET2_RX_ER__ENET2_RX_ER	0x1b0b0
> +				MX6UL_PAD_ENET2_RX_DATA0__ENET2_RDATA00	0x1b0b0
> +				MX6UL_PAD_ENET2_RX_DATA1__ENET2_RDATA01	0x1b0b0
> +				MX6UL_PAD_ENET2_TX_EN__ENET2_TX_EN	0x1b0b0
> +				MX6UL_PAD_ENET2_TX_DATA0__ENET2_TDATA00	0x1b0b0
> +				MX6UL_PAD_ENET2_TX_DATA1__ENET2_TDATA01	0x1b0b0
> +				MX6UL_PAD_ENET2_TX_CLK__ENET2_REF_CLK2	0x4001b031
> +				MX6UL_PAD_SNVS_TAMPER0__GPIO5_IO00	0x80000000

Do not use 0x80000000 but an explicit pad configuration value.

> +			>;
> +		};
> +
> +		pinctrl_flexcan1: flexcan1grp{
> +			fsl,pins = <
> +				MX6UL_PAD_UART3_RTS_B__FLEXCAN1_RX	0x1b020
> +				MX6UL_PAD_UART3_CTS_B__FLEXCAN1_TX	0x1b020
> +			>;
> +		};
> +
> +		pinctrl_flexcan2: flexcan2grp{
> +			fsl,pins = <
> +				MX6UL_PAD_UART2_RTS_B__FLEXCAN2_RX	0x1b020
> +				MX6UL_PAD_UART2_CTS_B__FLEXCAN2_TX	0x1b020
> +			>;
> +		};
> +
> +		pinctrl_lcdif_dat: lcdifdatgrp {
> +			fsl,pins = <
> +				MX6UL_PAD_LCD_DATA00__LCDIF_DATA00  0x79
> +				MX6UL_PAD_LCD_DATA01__LCDIF_DATA01  0x79
> +				MX6UL_PAD_LCD_DATA02__LCDIF_DATA02  0x79
> +				MX6UL_PAD_LCD_DATA03__LCDIF_DATA03  0x79
> +				MX6UL_PAD_LCD_DATA04__LCDIF_DATA04  0x79
> +				MX6UL_PAD_LCD_DATA05__LCDIF_DATA05  0x79
> +				MX6UL_PAD_LCD_DATA06__LCDIF_DATA06  0x79
> +				MX6UL_PAD_LCD_DATA07__LCDIF_DATA07  0x79
> +				MX6UL_PAD_LCD_DATA08__LCDIF_DATA08  0x79
> +				MX6UL_PAD_LCD_DATA09__LCDIF_DATA09  0x79
> +				MX6UL_PAD_LCD_DATA10__LCDIF_DATA10  0x79
> +				MX6UL_PAD_LCD_DATA11__LCDIF_DATA11  0x79
> +				MX6UL_PAD_LCD_DATA12__LCDIF_DATA12  0x79
> +				MX6UL_PAD_LCD_DATA13__LCDIF_DATA13  0x79
> +				MX6UL_PAD_LCD_DATA14__LCDIF_DATA14  0x79
> +				MX6UL_PAD_LCD_DATA15__LCDIF_DATA15  0x79
> +				MX6UL_PAD_LCD_DATA16__LCDIF_DATA16  0x79
> +				MX6UL_PAD_LCD_DATA17__LCDIF_DATA17  0x79
> +				MX6UL_PAD_LCD_DATA18__LCDIF_DATA18  0x79
> +				MX6UL_PAD_LCD_DATA19__LCDIF_DATA19  0x79
> +				MX6UL_PAD_LCD_DATA20__LCDIF_DATA20  0x79
> +				MX6UL_PAD_LCD_DATA21__LCDIF_DATA21  0x79
> +				MX6UL_PAD_LCD_DATA22__LCDIF_DATA22  0x79
> +				MX6UL_PAD_LCD_DATA23__LCDIF_DATA23  0x79
> +			>;
> +		};
> +
> +		pinctrl_lcdif_ctrl: lcdifctrlgrp {
> +			fsl,pins = <
> +				MX6UL_PAD_LCD_CLK__LCDIF_CLK	    0x79
> +				MX6UL_PAD_LCD_ENABLE__LCDIF_ENABLE  0x79
> +				MX6UL_PAD_LCD_HSYNC__LCDIF_HSYNC    0x79
> +				MX6UL_PAD_LCD_VSYNC__LCDIF_VSYNC    0x79
> +				/* used for lcd reset */
> +				MX6UL_PAD_SNVS_TAMPER9__GPIO5_IO09  0x79
> +			>;
> +		};
> +
> +		pinctrl_pwm1: pwm1grp {
> +			fsl,pins = <
> +				MX6UL_PAD_GPIO1_IO08__PWM1_OUT   0x110b0
> +			>;
> +		};
> +
> +		pinctrl_sim2_1: sim2grp-1 {

Drop "1" suffix.

> +			fsl,pins = <
> +				MX6UL_PAD_CSI_DATA03__SIM2_PORT1_PD		0xb808
> +				MX6UL_PAD_CSI_DATA04__SIM2_PORT1_CLK		0x31
> +				MX6UL_PAD_CSI_DATA05__SIM2_PORT1_RST_B		0xb808
> +				MX6UL_PAD_CSI_DATA06__SIM2_PORT1_SVEN		0xb808
> +				MX6UL_PAD_CSI_DATA07__SIM2_PORT1_TRXD		0xb809
> +				MX6UL_PAD_CSI_DATA02__GPIO4_IO23		0x3008
> +			>;
> +		};
> +
> +		pinctrl_uart1: uart1grp {
> +			fsl,pins = <
> +				MX6UL_PAD_UART1_TX_DATA__UART1_DCE_TX 0x1b0b1
> +				MX6UL_PAD_UART1_RX_DATA__UART1_DCE_RX 0x1b0b1
> +			>;
> +		};
> +
> +		pinctrl_uart2: uart2grp {
> +			fsl,pins = <
> +				MX6UL_PAD_UART2_TX_DATA__UART2_DCE_TX	0x1b0b1
> +				MX6UL_PAD_UART2_RX_DATA__UART2_DCE_RX	0x1b0b1
> +				MX6UL_PAD_UART3_RX_DATA__UART2_DCE_RTS	0x1b0b1
> +				MX6UL_PAD_UART3_TX_DATA__UART2_DCE_CTS	0x1b0b1
> +			>;
> +		};
> +
> +		pinctrl_uart2dte: uart2dtegrp {
> +			fsl,pins = <
> +				MX6UL_PAD_UART2_TX_DATA__UART2_DTE_RX	0x1b0b1
> +				MX6UL_PAD_UART2_RX_DATA__UART2_DTE_TX	0x1b0b1
> +				MX6UL_PAD_UART3_RX_DATA__UART2_DTE_CTS	0x1b0b1
> +				MX6UL_PAD_UART3_TX_DATA__UART2_DTE_RTS	0x1b0b1
> +			>;
> +		};
> +
> +		pinctrl_usdhc1: usdhc1grp {
> +			fsl,pins = <
> +				MX6UL_PAD_SD1_CMD__USDHC1_CMD     0x17059
> +				MX6UL_PAD_SD1_CLK__USDHC1_CLK     0x10059
> +				MX6UL_PAD_SD1_DATA0__USDHC1_DATA0 0x17059
> +				MX6UL_PAD_SD1_DATA1__USDHC1_DATA1 0x17059
> +				MX6UL_PAD_SD1_DATA2__USDHC1_DATA2 0x17059
> +				MX6UL_PAD_SD1_DATA3__USDHC1_DATA3 0x17059
> +			>;
> +		};
> +
> +		pinctrl_usdhc1_100mhz: usdhc1grp100mhz {
> +			fsl,pins = <
> +				MX6UL_PAD_SD1_CMD__USDHC1_CMD     0x170b9
> +				MX6UL_PAD_SD1_CLK__USDHC1_CLK     0x100b9
> +				MX6UL_PAD_SD1_DATA0__USDHC1_DATA0 0x170b9
> +				MX6UL_PAD_SD1_DATA1__USDHC1_DATA1 0x170b9
> +				MX6UL_PAD_SD1_DATA2__USDHC1_DATA2 0x170b9
> +				MX6UL_PAD_SD1_DATA3__USDHC1_DATA3 0x170b9
> +			>;
> +		};
> +
> +		pinctrl_usdhc1_200mhz: usdhc1grp200mhz {
> +			fsl,pins = <
> +				MX6UL_PAD_SD1_CMD__USDHC1_CMD     0x170f9
> +				MX6UL_PAD_SD1_CLK__USDHC1_CLK     0x100f9
> +				MX6UL_PAD_SD1_DATA0__USDHC1_DATA0 0x170f9
> +				MX6UL_PAD_SD1_DATA1__USDHC1_DATA1 0x170f9
> +				MX6UL_PAD_SD1_DATA2__USDHC1_DATA2 0x170f9
> +				MX6UL_PAD_SD1_DATA3__USDHC1_DATA3 0x170f9
> +			>;
> +		};
> +
> +		pinctrl_usdhc2: usdhc2grp {
> +			fsl,pins = <
> +				MX6UL_PAD_NAND_RE_B__USDHC2_CLK     0x17059
> +				MX6UL_PAD_NAND_WE_B__USDHC2_CMD     0x17059
> +				MX6UL_PAD_NAND_DATA00__USDHC2_DATA0 0x17059
> +				MX6UL_PAD_NAND_DATA01__USDHC2_DATA1 0x17059
> +				MX6UL_PAD_NAND_DATA02__USDHC2_DATA2 0x17059
> +				MX6UL_PAD_NAND_DATA03__USDHC2_DATA3 0x17059
> +			>;
> +		};
> +
> +		pinctrl_tsc: tscgrp {

Please keep these pinctrl group nodes sort alphabetically.

> +			fsl,pin = <
> +				MX6UL_PAD_GPIO1_IO01__GPIO1_IO01	0xb0
> +				MX6UL_PAD_GPIO1_IO02__GPIO1_IO02	0xb0
> +				MX6UL_PAD_GPIO1_IO03__GPIO1_IO03	0xb0
> +				MX6UL_PAD_GPIO1_IO04__GPIO1_IO04	0xb0
> +			>;
> +		};
> +
> +		pinctrl_i2c1: i2c1grp {
> +			fsl,pins = <
> +				MX6UL_PAD_UART4_TX_DATA__I2C1_SCL 0x4001b8b0
> +				MX6UL_PAD_UART4_RX_DATA__I2C1_SDA 0x4001b8b0
> +			>;
> +		};
> +
> +		pinctrl_i2c2: i2c2grp {
> +			fsl,pins = <
> +				MX6UL_PAD_UART5_TX_DATA__I2C2_SCL 0x4001b8b0
> +				MX6UL_PAD_UART5_RX_DATA__I2C2_SDA 0x4001b8b0
> +			>;
> +		};
> +
> +		pinctrl_qspi: qspigrp {
> +			fsl,pins = <
> +				MX6UL_PAD_NAND_WP_B__QSPI_A_SCLK      0x70a1
> +				MX6UL_PAD_NAND_READY_B__QSPI_A_DATA00 0x70a1
> +				MX6UL_PAD_NAND_CE0_B__QSPI_A_DATA01   0x70a1
> +				MX6UL_PAD_NAND_CE1_B__QSPI_A_DATA02   0x70a1
> +				MX6UL_PAD_NAND_CLE__QSPI_A_DATA03     0x70a1
> +				MX6UL_PAD_NAND_DQS__QSPI_A_SS0_B      0x70a1
> +			>;
> +		};
> +
> +		pinctrl_sai2: sai2grp {
> +			fsl,pins = <
> +				MX6UL_PAD_JTAG_TDI__SAI2_TX_BCLK	0x17088
> +				MX6UL_PAD_JTAG_TDO__SAI2_TX_SYNC	0x17088
> +				MX6UL_PAD_JTAG_TRST_B__SAI2_TX_DATA	0x11088
> +				MX6UL_PAD_JTAG_TCK__SAI2_RX_DATA	0x11088
> +				MX6UL_PAD_JTAG_TMS__SAI2_MCLK		0x17088
> +				MX6UL_PAD_SNVS_TAMPER4__GPIO5_IO04	0x17059
> +			>;
> +		};
> +
> +		pinctrl_spi4: spi4grp {
> +			fsl,pins = <
> +				MX6UL_PAD_BOOT_MODE0__GPIO5_IO10	0x70a1
> +				MX6UL_PAD_BOOT_MODE1__GPIO5_IO11	0x70a1
> +				MX6UL_PAD_SNVS_TAMPER7__GPIO5_IO07	0x70a1
> +				MX6UL_PAD_SNVS_TAMPER8__GPIO5_IO08	0x80000000

Use an explicit pad configuration value.

> +			>;
> +		};
> +	};
> +};
> diff --git a/arch/arm/boot/dts/imx6ul.dtsi b/arch/arm/boot/dts/imx6ul.dtsi
> new file mode 100644
> index 0000000..e23a8c7
> --- /dev/null
> +++ b/arch/arm/boot/dts/imx6ul.dtsi
> @@ -0,0 +1,645 @@
> +/*
> + * Copyright 2015 Freescale Semiconductor, Inc.
> + *
> + * This program is free software; you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License version 2 as
> + * published by the Free Software Foundation.
> + */
> +
> +#include <dt-bindings/clock/imx6ul-clock.h>
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/interrupt-controller/arm-gic.h>
> +#include "imx6ul-pinfunc.h"
> +#include "skeleton.dtsi"
> +
> +/ {
> +	aliases {
> +		gpio0 = &gpio1;
> +		gpio1 = &gpio2;
> +		gpio2 = &gpio3;
> +		gpio3 = &gpio4;
> +		gpio4 = &gpio5;
> +		i2c0 = &i2c1;
> +		i2c1 = &i2c2;
> +		i2c2 = &i2c3;
> +		i2c3 = &i2c4;
> +		mmc0 = &usdhc1;
> +		mmc1 = &usdhc2;
> +		serial0 = &uart1;
> +		serial1 = &uart2;
> +		serial2 = &uart3;
> +		serial3 = &uart4;
> +		serial4 = &uart5;
> +		serial5 = &uart6;
> +		serial6 = &uart7;
> +		serial7 = &uart8;
> +		spi0 = &ecspi1;
> +		spi1 = &ecspi2;
> +		spi2 = &ecspi3;
> +		spi3 = &ecspi4;
> +		usbphy0 = &usbphy1;
> +		usbphy1 = &usbphy2;
> +	};
> +
> +	cpus {
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +
> +		cpu0: cpu at 0 {
> +			compatible = "arm,cortex-a7";
> +			device_type = "cpu";
> +			reg = <0>;
> +			clock-latency = <61036>; /* two CLK32 periods */
> +			operating-points = <
> +				/* kHz	uV */
> +				528000	1250000
> +				396000	1150000
> +				198000	1150000
> +			>;
> +			fsl,soc-operating-points = <
> +				/* KHz	uV */
> +				528000	1250000
> +				396000	1150000
> +				198000	1150000
> +			>;
> +			clocks = <&clks IMX6UL_CLK_ARM>,
> +				 <&clks IMX6UL_CLK_PLL2_BUS>,
> +				 <&clks IMX6UL_CLK_PLL2_PFD2>,
> +				 <&clks IMX6UL_CA7_SECONDARY_SEL>,
> +				 <&clks IMX6UL_CLK_STEP>,
> +				 <&clks IMX6UL_CLK_PLL1_SW>,
> +				 <&clks IMX6UL_CLK_PLL1_SYS>,
> +				 <&clks IMX6UL_PLL1_BYPASS>,
> +				 <&clks IMX6UL_CLK_PLL1>,
> +				 <&clks IMX6UL_PLL1_BYPASS_SRC>,
> +				 <&clks IMX6UL_CLK_OSC>;
> +			clock-names = "arm", "pll2_bus",  "pll2_pfd2_396m", "secondary_sel", "step",
> +				      "pll1_sw", "pll1_sys", "pll1_bypass", "pll1", "pll1_bypass_src", "osc";

Wrap these two lines to make them a bit shorter.

> +		};
> +	};
> +
> +	intc: interrupt-controller at 00a01000 {
> +		compatible = "arm,cortex-a7-gic";
> +		#interrupt-cells = <3>;
> +		interrupt-controller;
> +		reg = <0x00a01000 0x1000>,
> +		      <0x00a02000 0x1000>,
> +		      <0x00a04000 0x2000>,
> +		      <0x00a06000 0x2000>;
> +	};
> +
> +	ckil: clock-cli {
> +		compatible = "fixed-clock";
> +		#clock-cells = <0>;
> +		clock-frequency = <32768>;
> +		clock-output-names = "ckil";
> +	};
> +
> +	osc: clock-osc {
> +		compatible = "fixed-clock";
> +		#clock-cells = <0>;
> +		clock-frequency = <24000000>;
> +		clock-output-names = "osc";
> +	};
> +
> +	ipp_di0: clock-di0 {
> +		compatible = "fixed-clock";
> +		#clock-cells = <0>;
> +		clock-frequency = <0>;
> +		clock-output-names = "ipp_di0";
> +	};
> +
> +	ipp_di1: clock-di1 {
> +		compatible = "fixed-clock";
> +		#clock-cells = <0>;
> +		clock-frequency = <0>;
> +		clock-output-names = "ipp_di1";
> +	};
> +
> +	soc {
> +		#address-cells = <1>;
> +		#size-cells = <1>;
> +		compatible = "simple-bus";
> +		interrupt-parent = <&intc>;
> +		ranges;
> +
> +		pmu {
> +			compatible = "arm,cortex-a7-pmu";
> +			interrupts = <GIC_SPI 94 IRQ_TYPE_LEVEL_HIGH>;
> +			status = "disabled";
> +		};
> +
> +		aips1: aips-bus at 02000000 {
> +			compatible = "fsl,aips-bus", "simple-bus";
> +			#address-cells = <1>;
> +			#size-cells = <1>;
> +			reg = <0x02000000 0x100000>;
> +			ranges;
> +
> +			spba-bus at 02000000 {
> +				compatible = "fsl,spba-bus", "simple-bus";
> +				#address-cells = <1>;
> +				#size-cells = <1>;
> +				reg = <0x02000000 0x40000>;
> +				ranges;
> +
> +				ecspi1: ecspi at 02008000 {
> +					#address-cells = <1>;
> +					#size-cells = <0>;
> +					compatible = "fsl,imx6ul-ecspi", "fsl,imx51-ecspi";
> +					reg = <0x02008000 0x4000>;
> +					interrupts = <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>;
> +					clocks = <&clks IMX6UL_CLK_ECSPI1>,
> +						 <&clks IMX6UL_CLK_ECSPI1>;
> +					clock-names = "ipg", "per";
> +					status = "disabled";
> +				};
> +
> +				ecspi2: ecspi at 0200c000 {
> +					#address-cells = <1>;
> +					#size-cells = <0>;
> +					compatible = "fsl,imx6ul-ecspi", "fsl,imx51-ecspi";
> +					reg = <0x0200c000 0x4000>;
> +					interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>;
> +					clocks = <&clks IMX6UL_CLK_ECSPI2>,
> +						 <&clks IMX6UL_CLK_ECSPI2>;
> +					clock-names = "ipg", "per";
> +					status = "disabled";
> +				};
> +
> +				ecspi3: ecspi at 02010000 {
> +					#address-cells = <1>;
> +					#size-cells = <0>;
> +					compatible = "fsl,imx6ul-ecspi", "fsl,imx51-ecspi";
> +					reg = <0x02010000 0x4000>;
> +					interrupts = <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>;
> +					clocks = <&clks IMX6UL_CLK_ECSPI3>,
> +						 <&clks IMX6UL_CLK_ECSPI3>;
> +					clock-names = "ipg", "per";
> +					status = "disabled";
> +				};
> +
> +				ecspi4: ecspi at 02014000 {
> +					#address-cells = <1>;
> +					#size-cells = <0>;
> +					compatible = "fsl,imx6ul-ecspi", "fsl,imx51-ecspi";
> +					reg = <0x02014000 0x4000>;
> +					interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>;
> +					clocks = <&clks IMX6UL_CLK_ECSPI4>,
> +						 <&clks IMX6UL_CLK_ECSPI4>;
> +					clock-names = "ipg", "per";
> +					status = "disabled";
> +				};
> +
> +				uart7: serial at 02018000 {
> +					compatible = "fsl,imx6ul-uart",
> +						     "fsl,imx6q-uart", "fsl,imx21-uart";

"fsl,imx21-uart" can just be dropped?

> +					reg = <0x02018000 0x4000>;
> +					interrupts = <GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH>;
> +					clocks = <&clks IMX6UL_CLK_UART7_IPG>,
> +						 <&clks IMX6UL_CLK_UART7_SERIAL>;
> +					clock-names = "ipg", "per";
> +					status = "disabled";
> +				};
> +
> +				uart1: serial at 02020000 {
> +					compatible = "fsl,imx6ul-uart",
> +						     "fsl,imx6q-uart", "fsl,imx21-uart";
> +					reg = <0x02020000 0x4000>;
> +					interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>;
> +					clocks = <&clks IMX6UL_CLK_UART1_IPG>,
> +						 <&clks IMX6UL_CLK_UART1_SERIAL>;
> +					clock-names = "ipg", "per";
> +					status = "disabled";
> +				};
> +
> +				uart8: serial at 02024000 {
> +					compatible = "fsl,imx6ul-uart",
> +						     "fsl,imx6q-uart", "fsl,imx21-uart";
> +					reg = <0x02024000 0x4000>;
> +					interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>;
> +					clocks = <&clks IMX6UL_CLK_UART8_IPG>,
> +						 <&clks IMX6UL_CLK_UART8_SERIAL>;
> +					clock-names = "ipg", "per";
> +					status = "disabled";
> +				};
> +			};
> +
> +

One new line is enough.

> +			pwm1: pwm at 02080000 {
> +				compatible = "fsl,imx6ul-pwm", "fsl,imx27-pwm";
> +				reg = <0x02080000 0x4000>;
> +				interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>;
> +				clocks = <&clks IMX6UL_CLK_PWM1>,
> +					 <&clks IMX6UL_CLK_PWM1>;
> +				clock-names = "ipg", "per";
> +				#pwm-cells = <2>;
> +			};
> +
> +			pwm2: pwm at 02084000 {
> +				compatible = "fsl,imx6ul-pwm", "fsl,imx27-pwm";
> +				reg = <0x02084000 0x4000>;
> +				interrupts = <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>;
> +				clocks = <&clks IMX6UL_CLK_DUMMY>,
> +					 <&clks IMX6UL_CLK_DUMMY>;

Why all other pwm devices except pwm1 are using dummy clock?

> +				clock-names = "ipg", "per";
> +				#pwm-cells = <2>;
> +			};
> +
> +			pwm3: pwm at 02088000 {
> +				compatible = "fsl,imx6ul-pwm", "fsl,imx27-pwm";
> +				reg = <0x02088000 0x4000>;
> +				interrupts = <GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>;
> +				clocks = <&clks IMX6UL_CLK_DUMMY>,
> +					 <&clks IMX6UL_CLK_DUMMY>;
> +				clock-names = "ipg", "per";
> +				#pwm-cells = <2>;
> +			};
> +
> +			pwm4: pwm at 0208c000 {
> +				compatible = "fsl,imx6ul-pwm", "fsl,imx27-pwm";
> +				reg = <0x0208c000 0x4000>;
> +				interrupts = <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>;
> +				clocks = <&clks IMX6UL_CLK_DUMMY>,
> +					 <&clks IMX6UL_CLK_DUMMY>;
> +				clock-names = "ipg", "per";
> +				#pwm-cells = <2>;
> +			};
> +
> +			gpt1: gpt at 02098000 {
> +				compatible = "fsl,imx6ul-gpt", "fsl,imx6sx-gpt";
> +				reg = <0x02098000 0x4000>;
> +				interrupts = <GIC_SPI 55 IRQ_TYPE_LEVEL_HIGH>;
> +				clocks = <&clks IMX6UL_CLK_GPT1_BUS>,
> +					 <&clks IMX6UL_CLK_GPT1_SERIAL>;
> +				clock-names = "ipg", "per";
> +			};
> +
> +			gpio1: gpio at 0209c000 {
> +				compatible = "fsl,imx6ul-gpio", "fsl,imx35-gpio";
> +				reg = <0x0209c000 0x4000>;
> +				interrupts = <GIC_SPI 66 IRQ_TYPE_LEVEL_HIGH>,
> +					     <GIC_SPI 67 IRQ_TYPE_LEVEL_HIGH>;
> +				gpio-controller;
> +				#gpio-cells = <2>;
> +				interrupt-controller;
> +				#interrupt-cells = <2>;
> +			};
> +
> +			gpio2: gpio at 020a0000 {
> +				compatible = "fsl,imx6ul-gpio", "fsl,imx35-gpio";
> +				reg = <0x020a0000 0x4000>;
> +				interrupts = <GIC_SPI 68 IRQ_TYPE_LEVEL_HIGH>,
> +					     <GIC_SPI 69 IRQ_TYPE_LEVEL_HIGH>;
> +				gpio-controller;
> +				#gpio-cells = <2>;
> +				interrupt-controller;
> +				#interrupt-cells = <2>;
> +			};
> +
> +			gpio3: gpio at 020a4000 {
> +				compatible = "fsl,imx6ul-gpio", "fsl,imx35-gpio";
> +				reg = <0x020a4000 0x4000>;
> +				interrupts = <GIC_SPI 70 IRQ_TYPE_LEVEL_HIGH>,
> +					     <GIC_SPI 71 IRQ_TYPE_LEVEL_HIGH>;
> +				gpio-controller;
> +				#gpio-cells = <2>;
> +				interrupt-controller;
> +				#interrupt-cells = <2>;
> +			};
> +
> +			gpio4: gpio at 020a8000 {
> +				compatible = "fsl,imx6ul-gpio", "fsl,imx35-gpio";
> +				reg = <0x020a8000 0x4000>;
> +				interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>,
> +					     <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>;
> +				gpio-controller;
> +				#gpio-cells = <2>;
> +				interrupt-controller;
> +				#interrupt-cells = <2>;
> +			};
> +
> +			gpio5: gpio at 020ac000 {
> +				compatible = "fsl,imx6ul-gpio", "fsl,imx35-gpio";
> +				reg = <0x020ac000 0x4000>;
> +				interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>,
> +					     <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>;
> +				gpio-controller;
> +				#gpio-cells = <2>;
> +				interrupt-controller;
> +				#interrupt-cells = <2>;
> +			};
> +
> +			wdog1: wdog at 020bc000 {
> +				compatible = "fsl,imx6ul-wdt", "fsl,imx21-wdt";
> +				reg = <0x020bc000 0x4000>;
> +				interrupts = <GIC_SPI 80 IRQ_TYPE_LEVEL_HIGH>;
> +				clocks = <&clks IMX6UL_CLK_WDOG1>;
> +			};
> +
> +			wdog2: wdog at 020c0000 {
> +				compatible = "fsl,imx6ul-wdt", "fsl,imx21-wdt";
> +				reg = <0x020c0000 0x4000>;
> +				interrupts = <GIC_SPI 81 IRQ_TYPE_LEVEL_HIGH>;
> +				clocks = <&clks IMX6UL_CLK_WDOG2>;
> +				status = "disabled";
> +			};
> +
> +			clks: ccm at 020c4000 {
> +				compatible = "fsl,imx6ul-ccm";
> +				reg = <0x020c4000 0x4000>;
> +				interrupts = <GIC_SPI 87 IRQ_TYPE_LEVEL_HIGH>,
> +					     <GIC_SPI 88 IRQ_TYPE_LEVEL_HIGH>;
> +				#clock-cells = <1>;
> +				clocks = <&ckil>, <&osc>, <&ipp_di0>, <&ipp_di1>;
> +				clock-names = "ckil", "osc", "ipp_di0", "ipp_di1";
> +			};
> +
> +			anatop: anatop at 020c8000 {
> +				compatible = "fsl,imx6ul-anatop", "fsl,imx6q-anatop",
> +					     "syscon", "simple-bus";
> +				reg = <0x020c8000 0x1000>;
> +				interrupts = <GIC_SPI 49 IRQ_TYPE_LEVEL_HIGH>,
> +					     <GIC_SPI 54 IRQ_TYPE_LEVEL_HIGH>,
> +					     <GIC_SPI 127 IRQ_TYPE_LEVEL_HIGH>;
> +
> +				reg_3p0: regulator-3p0 at 120 {
> +					compatible = "fsl,anatop-regulator";
> +					regulator-name = "vdd3p0";
> +					regulator-min-microvolt = <2625000>;
> +					regulator-max-microvolt = <3400000>;
> +					anatop-reg-offset = <0x120>;
> +					anatop-vol-bit-shift = <8>;
> +					anatop-vol-bit-width = <5>;
> +					anatop-min-bit-val = <0>;
> +					anatop-min-voltage = <2625000>;
> +					anatop-max-voltage = <3400000>;
> +					anatop-enable-bit = <0>;
> +				};
> +
> +				reg_arm: regulator-vddcore at 140 {
> +					compatible = "fsl,anatop-regulator";
> +					regulator-name = "cpu";
> +					regulator-min-microvolt = <725000>;
> +					regulator-max-microvolt = <1450000>;
> +					regulator-always-on;
> +					anatop-reg-offset = <0x140>;
> +					anatop-vol-bit-shift = <0>;
> +					anatop-vol-bit-width = <5>;
> +					anatop-delay-reg-offset = <0x170>;
> +					anatop-delay-bit-shift = <24>;
> +					anatop-delay-bit-width = <2>;
> +					anatop-min-bit-val = <1>;
> +					anatop-min-voltage = <725000>;
> +					anatop-max-voltage = <1450000>;
> +				};
> +
> +				reg_soc: regulator-vddsoc at 140 {
> +					compatible = "fsl,anatop-regulator";
> +					regulator-name = "vddsoc";
> +					regulator-min-microvolt = <725000>;
> +					regulator-max-microvolt = <1450000>;
> +					regulator-always-on;
> +					anatop-reg-offset = <0x140>;
> +					anatop-vol-bit-shift = <18>;
> +					anatop-vol-bit-width = <5>;
> +					anatop-delay-reg-offset = <0x170>;
> +					anatop-delay-bit-shift = <28>;
> +					anatop-delay-bit-width = <2>;
> +					anatop-min-bit-val = <1>;
> +					anatop-min-voltage = <725000>;
> +					anatop-max-voltage = <1450000>;
> +				};
> +			};
> +
> +			usbphy1: usbphy at 020c9000 {
> +				compatible = "fsl,imx6ul-usbphy", "fsl,imx23-usbphy";
> +				reg = <0x020c9000 0x1000>;
> +				interrupts = <GIC_SPI 44 IRQ_TYPE_LEVEL_HIGH>;
> +				clocks = <&clks IMX6UL_CLK_USBPHY1>;
> +				phy-3p0-supply = <&reg_3p0>;
> +				fsl,anatop = <&anatop>;
> +			};
> +
> +			usbphy2: usbphy at 020ca000 {
> +				compatible = "fsl,imx6ul-usbphy", "fsl,imx23-usbphy";
> +				reg = <0x020ca000 0x1000>;
> +				interrupts = <GIC_SPI 45 IRQ_TYPE_LEVEL_HIGH>;
> +				clocks = <&clks IMX6UL_CLK_USBPHY2>;
> +				phy-3p0-supply = <&reg_3p0>;
> +				fsl,anatop = <&anatop>;
> +			};
> +
> +			epit1: epit at 020d0000 {
> +				reg = <0x020d0000 0x4000>;
> +				interrupts = <GIC_SPI 56 IRQ_TYPE_LEVEL_HIGH>;
> +			};
> +
> +			epit2: epit at 020d4000 {
> +				reg = <0x020d4000 0x4000>;
> +				interrupts = <GIC_SPI 57 IRQ_TYPE_LEVEL_HIGH>;
> +			};
> +
> +			src: src at 020d8000 {
> +				compatible = "fsl,imx6ul-src", "fsl,imx51-src";
> +				reg = <0x020d8000 0x4000>;
> +				interrupts = <GIC_SPI 91 IRQ_TYPE_LEVEL_HIGH>,
> +					     <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>;
> +				#reset-cells = <1>;
> +			};
> +
> +			gpc: gpc at 020dc000 {
> +				compatible = "fsl,imx6ul-gpc", "fsl,imx6q-gpc";
> +				reg = <0x020dc000 0x4000>;
> +				interrupts = <GIC_SPI 89 IRQ_TYPE_LEVEL_HIGH>;
> +				fsl,mf-mix-wakeup-irq = <0x7c00000 0x3d00 0x0 0x1400240>;

I cannot find this property in any bindings doc.

Shawn

> +			};
> +
> +			iomuxc: iomuxc at 020e0000 {
> +				compatible = "fsl,imx6ul-iomuxc";
> +				reg = <0x020e0000 0x4000>;
> +			};
> +
> +			gpr: iomuxc-gpr at 020e4000 {
> +				compatible = "fsl,imx6ul-iomuxc-gpr", "syscon";
> +				reg = <0x020e4000 0x4000>;
> +			};
> +
> +			gpt2: gpt at 020e8000 {
> +				compatible = "fsl,imx6ul-gpt", "fsl,imx6sx-gpt";
> +				reg = <0x020e8000 0x4000>;
> +				interrupts = <GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH>;
> +				clocks = <&clks IMX6UL_CLK_DUMMY>,
> +					 <&clks IMX6UL_CLK_DUMMY>;
> +				clock-names = "ipg", "per";
> +			};
> +
> +			pwm5: pwm at 020f0000 {
> +				compatible = "fsl,imx6ul-pwm", "fsl,imx27-pwm";
> +				reg = <0x020f0000 0x4000>;
> +				interrupts = <GIC_SPI 114 IRQ_TYPE_LEVEL_HIGH>;
> +				clocks = <&clks IMX6UL_CLK_DUMMY>,
> +					 <&clks IMX6UL_CLK_DUMMY>;
> +				clock-names = "ipg", "per";
> +				#pwm-cells = <2>;
> +			};
> +
> +			pwm6: pwm at 020f4000 {
> +				compatible = "fsl,imx6ul-pwm", "fsl,imx27-pwm";
> +				reg = <0x020f4000 0x4000>;
> +				interrupts = <GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH>;
> +				clocks = <&clks IMX6UL_CLK_DUMMY>,
> +					 <&clks IMX6UL_CLK_DUMMY>;
> +				clock-names = "ipg", "per";
> +				#pwm-cells = <2>;
> +			};
> +
> +			pwm7: pwm at 020f8000 {
> +				compatible = "fsl,imx6ul-pwm", "fsl,imx27-pwm";
> +				reg = <0x020f8000 0x4000>;
> +				interrupts = <GIC_SPI 116 IRQ_TYPE_LEVEL_HIGH>;
> +				clocks = <&clks IMX6UL_CLK_DUMMY>,
> +					 <&clks IMX6UL_CLK_DUMMY>;
> +				clock-names = "ipg", "per";
> +				#pwm-cells = <2>;
> +			};
> +
> +			pwm8: pwm at 020fc000 {
> +				compatible = "fsl,imx6ul-pwm", "fsl,imx27-pwm";
> +				reg = <0x020fc000 0x4000>;
> +				interrupts = <GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>;
> +				clocks = <&clks IMX6UL_CLK_DUMMY>,
> +					 <&clks IMX6UL_CLK_DUMMY>;
> +				clock-names = "ipg", "per";
> +				#pwm-cells = <2>;
> +			};
> +		};
> +
> +		aips2: aips-bus at 02100000 {
> +			compatible = "fsl,aips-bus", "simple-bus";
> +			#address-cells = <1>;
> +			#size-cells = <1>;
> +			reg = <0x02100000 0x100000>;
> +			ranges;
> +
> +			usdhc1: usdhc at 02190000 {
> +				compatible = "fsl,imx6ul-usdhc", "fsl,imx6sx-usdhc";
> +				reg = <0x02190000 0x4000>;
> +				interrupts = <GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH>;
> +				clocks = <&clks IMX6UL_CLK_USDHC1>,
> +					 <&clks IMX6UL_CLK_USDHC1>,
> +					 <&clks IMX6UL_CLK_USDHC1>;
> +				clock-names = "ipg", "ahb", "per";
> +				bus-width = <4>;
> +				status = "disabled";
> +			};
> +
> +			usdhc2: usdhc at 02194000 {
> +				compatible = "fsl,imx6ul-usdhc", "fsl,imx6sx-usdhc";
> +				reg = <0x02194000 0x4000>;
> +				interrupts = <GIC_SPI 23 IRQ_TYPE_LEVEL_HIGH>;
> +				clocks = <&clks IMX6UL_CLK_USDHC2>,
> +					 <&clks IMX6UL_CLK_USDHC2>,
> +					 <&clks IMX6UL_CLK_USDHC2>;
> +				clock-names = "ipg", "ahb", "per";
> +				bus-width = <4>;
> +				status = "disabled";
> +			};
> +
> +			i2c1: i2c at 021a0000 {
> +				#address-cells = <1>;
> +				#size-cells = <0>;
> +				compatible = "fsl,imx6ul-i2c", "fsl,imx21-i2c";
> +				reg = <0x021a0000 0x4000>;
> +				interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>;
> +				clocks = <&clks IMX6UL_CLK_I2C1>;
> +				status = "disabled";
> +			};
> +
> +			i2c2: i2c at 021a4000 {
> +				#address-cells = <1>;
> +				#size-cells = <0>;
> +				compatible = "fsl,imx6ul-i2c", "fsl,imx21-i2c";
> +				reg = <0x021a4000 0x4000>;
> +				interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
> +				clocks = <&clks IMX6UL_CLK_I2C2>;
> +				status = "disabled";
> +			};
> +
> +			i2c3: i2c at 021a8000 {
> +				#address-cells = <1>;
> +				#size-cells = <0>;
> +				compatible = "fsl,imx6ul-i2c", "fsl,imx21-i2c";
> +				reg = <0x021a8000 0x4000>;
> +				interrupts = <GIC_SPI 38 IRQ_TYPE_LEVEL_HIGH>;
> +				clocks = <&clks IMX6UL_CLK_I2C3>;
> +				status = "disabled";
> +			};
> +
> +			uart2: serial at 021e8000 {
> +				compatible = "fsl,imx6ul-uart",
> +					     "fsl,imx6q-uart", "fsl,imx21-uart";
> +				reg = <0x021e8000 0x4000>;
> +				interrupts = <GIC_SPI 27 IRQ_TYPE_LEVEL_HIGH>;
> +				clocks = <&clks IMX6UL_CLK_UART2_IPG>,
> +					 <&clks IMX6UL_CLK_UART2_SERIAL>;
> +				clock-names = "ipg", "per";
> +				status = "disabled";
> +			};
> +
> +			uart3: serial at 021ec000 {
> +				compatible = "fsl,imx6ul-uart",
> +					     "fsl,imx6q-uart", "fsl,imx21-uart";
> +				reg = <0x021ec000 0x4000>;
> +				interrupts = <GIC_SPI 28 IRQ_TYPE_LEVEL_HIGH>;
> +				clocks = <&clks IMX6UL_CLK_UART3_IPG>,
> +					 <&clks IMX6UL_CLK_UART3_SERIAL>;
> +				clock-names = "ipg", "per";
> +				status = "disabled";
> +			};
> +
> +			uart4: serial at 021f0000 {
> +				compatible = "fsl,imx6ul-uart",
> +					     "fsl,imx6q-uart", "fsl,imx21-uart";
> +				reg = <0x021f0000 0x4000>;
> +				interrupts = <GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>;
> +				clocks = <&clks IMX6UL_CLK_UART4_IPG>,
> +					 <&clks IMX6UL_CLK_UART4_SERIAL>;
> +				clock-names = "ipg", "per";
> +				status = "disabled";
> +			};
> +
> +			uart5: serial at 021f4000 {
> +				compatible = "fsl,imx6ul-uart",
> +					     "fsl,imx6q-uart", "fsl,imx21-uart";
> +				reg = <0x021f4000 0x4000>;
> +				interrupts = <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>;
> +				clocks = <&clks IMX6UL_CLK_UART5_IPG>,
> +					 <&clks IMX6UL_CLK_UART5_SERIAL>;
> +				clock-names = "ipg", "per";
> +				status = "disabled";
> +			};
> +
> +			i2c4: i2c at 021f8000 {
> +				#address-cells = <1>;
> +				#size-cells = <0>;
> +				compatible = "fsl,imx6ul-i2c", "fsl,imx21-i2c";
> +				reg = <0x021f8000 0x4000>;
> +				interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>;
> +				clocks = <&clks IMX6UL_CLK_I2C4>;
> +				status = "disabled";
> +			};
> +
> +			uart6: serial at 021fc000 {
> +				compatible = "fsl,imx6ul-uart",
> +					     "fsl,imx6q-uart", "fsl,imx21-uart";
> +				reg = <0x021fc000 0x4000>;
> +				interrupts = <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>;
> +				clocks = <&clks IMX6UL_CLK_UART6_IPG>,
> +					 <&clks IMX6UL_CLK_UART6_SERIAL>;
> +				clock-names = "ipg", "per";
> +				status = "disabled";
> +			};
> +		};
> +	};
> +};
> -- 
> 1.9.1
> 
> 
> _______________________________________________
> linux-arm-kernel mailing list
> linux-arm-kernel at lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
> 



More information about the linux-arm-kernel mailing list