[PATCH v3 2/5] PCI: designware: Add ARM64 support

[Zhou Wang]

On 2015/7/1 22:26, James Morse wrote:
> Zhou Wang wrote:
>> I tested this patch on D02 board of Hisilicon. It works well.
>> I have compiled the driver with multi_v7_defconfig. However, I don't
>> have
>> ARM32 PCIe related board to do test. It will be appreciated if someone
>> could
>> help to test it.
>>
>> Signed-off-by: Zhou Wang <wangzhou1 at hisilicon.com>
>> Signed-off-by: Arnd Bergmann <arnd at arndb.de>
>> Signed-off-by: Gabriele Paoloni <gabriele.paoloni at huawei.com>
>> Tested-by: Fabrice Gasnier <fabrice.gasnier at st.com>
>> Tested-by: James Morse <james.morse at arm.com>
> 
> Tests on this new series, using the same i.MX 6Quad board, are not working.
> 
> The network card is no longer detected, and I get a lockup when removing
> the root bridge and rescanning.
> 
> Partial dmesg output below. Significantly, the lines:
>> [    0.152128] PCI host bridge /soc/pcie at 0x01000000 ranges:
>> [    0.152142]   No bus range found for /soc/pcie at 0x01000000, using [bus
> 00-ff]
> are new.
> 
> Both series are applied to v4.1, use the same .config file, and the same dtb.
> I will investigate further.
> 
> (Re-testing v2 works, so this isn't an interim hardware failure)
> 
> Thanks,
> 
> James
>

Hi James,

There are something wrong with v3 patch.

pp->io_mod_base = of_read_number(parser_range_end -
		of_n_addr_cells(np) - 5 + na, ns);
pp->mem_mod_base = of_read_number(parser_range_end -
		of_n_addr_cells(np) - 5 + na, ns);
pp->cfg0_mod_base = of_read_number(parser_range_end -
		of_n_addr_cells(np) - 5 + na, ns);
are wrong.

The ranges item in your dts is:
ranges = <0x800 0x0 0x1f00000 0x1f00000 0x0 0x80000
	  0x81000000 0x0 0x0  0x1f80000 0x0 0x10000
	  0x82000000 0x0 0x1000000 0x1000000 0x0 0xf00000>;
parser_range_end points to the end of ranges(0xf00000) directly. In v2 patch,
of_read_number is of_read_number(parser.range - parser.np + na, ns); parser.range
points to the end of each line in ranges item.

When I did test on D02 board with intel82599 card, I set ranges item as:
ranges = <0x03000000 0 0xb0000000 0x220 0x00000000 0 0xf000000>;
It is just one line. In this case, parser_range_end is same with parser.range.
That is why it happened to work well on D02 board.

very sorry to bother you about this problem.

Thanks,
Zhou

> 
> 
> root at localhost:~# dmesg | grep -i pci
> [    0.126184] PCI: CLS 0 bytes, default 64
> [    0.152128] PCI host bridge /soc/pcie at 0x01000000 ranges:
> [    0.152142]   No bus range found for /soc/pcie at 0x01000000, using [bus 00-ff]
> [    0.154183] imx6q-pcie 1ffc000.pcie: PCI host bridge to bus 0000:00
> [    0.154201] pci_bus 0000:00: root bus resource [bus 00-ff]
> [    0.154215] pci_bus 0000:00: root bus resource [???
> 0x01f00000-0x01f7ffff flags 0x0]
> [    0.154228] pci_bus 0000:00: root bus resource [io  0x0000-0xffff]
> [    0.154270] pci_bus 0000:00: root bus resource [mem 0x01000000-0x01efffff]
> [    0.154306] pci 0000:00:00.0: [16c3:abcd] type 01 class 0x060400
> [    0.154333] pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x000fffff]
> [    0.154352] pci 0000:00:00.0: reg 0x38: [mem 0x00000000-0x0000ffff pref]
> [    0.154377] pci 0000:00:00.0: IOMMU is currently not supported for PCI
> [    0.154429] pci 0000:00:00.0: supports D1
> [    0.154440] pci 0000:00:00.0: PME# supported from D0 D1 D3hot D3cold
> [    0.154683] PCI: bus0: Fast back to back transfers disabled
> [    0.154806] PCI: bus1: Fast back to back transfers enabled
> [    0.154884] pci 0000:00:00.0: BAR 0: assigned [mem 0x01000000-0x010fffff]
> [    0.154903] pci 0000:00:00.0: BAR 6: assigned [mem 0x01100000-0x0110ffff
> pref]
> [    0.154917] pci 0000:00:00.0: PCI bridge to [bus 01]
> [    0.155145] pcieport 0000:00:00.0: Signaling PME through PCIe PME interrupt
> [    0.155161] pcie_pme 0000:00:00.0:pcie01: service driver pcie_pme loaded
> [    0.155279] aer 0000:00:00.0:pcie02: service driver aer loaded
> [    1.188840] ehci-pci: EHCI PCI platform driver
> [    1.232518] ohci-pci: OHCI PCI platform driver
> 
> --
> To unsubscribe from this list: send the line "unsubscribe linux-pci" in
> the body of a message to majordomo at vger.kernel.org
> More majordomo info at  http://vger.kernel.org/majordomo-info.html
> 
> .
>