[PATCH v6 1/2] mtd: hisilicon: add a new NAND controller driver for hisilicon hip04 Soc
Zhou Wang
wangzhou1 at hisilicon.com
Wed Jan 14 04:34:39 PST 2015
On 2015/1/13 11:58, Brian Norris wrote:
> On Mon, Jan 12, 2015 at 03:28:53PM +0800, Zhou Wang wrote:
>> Signed-off-by: Zhou Wang <wangzhou1 at hisilicon.com>
>
> Mostly good. A few small comments.
>
>> ---
>> drivers/mtd/nand/Kconfig | 5 +
>> drivers/mtd/nand/Makefile | 1 +
>> drivers/mtd/nand/hisi504_nand.c | 907 ++++++++++++++++++++++++++++++++++++++++
>> 3 files changed, 913 insertions(+)
>> create mode 100644 drivers/mtd/nand/hisi504_nand.c
>>
>> diff --git a/drivers/mtd/nand/Kconfig b/drivers/mtd/nand/Kconfig
>> index 7d0150d..e1220fc 100644
>> --- a/drivers/mtd/nand/Kconfig
>> +++ b/drivers/mtd/nand/Kconfig
>> @@ -524,4 +524,9 @@ config MTD_NAND_SUNXI
>> help
>> Enables support for NAND Flash chips on Allwinner SoCs.
>>
>> +config MTD_NAND_HISI504
>> + tristate "Support for NAND controller on Hisilicon SoC Hip04"
>> + help
>> + Enables support for NAND controller on Hisilicon SoC Hip04.
>> +
>> endif # MTD_NAND
>> diff --git a/drivers/mtd/nand/Makefile b/drivers/mtd/nand/Makefile
>> index bd38f21..582bbd05 100644
>> --- a/drivers/mtd/nand/Makefile
>> +++ b/drivers/mtd/nand/Makefile
>> @@ -51,5 +51,6 @@ obj-$(CONFIG_MTD_NAND_GPMI_NAND) += gpmi-nand/
>> obj-$(CONFIG_MTD_NAND_XWAY) += xway_nand.o
>> obj-$(CONFIG_MTD_NAND_BCM47XXNFLASH) += bcm47xxnflash/
>> obj-$(CONFIG_MTD_NAND_SUNXI) += sunxi_nand.o
>> +obj-$(CONFIG_MTD_NAND_HISI504) += hisi504_nand.o
>>
>> nand-objs := nand_base.o nand_bbt.o nand_timings.o
>> diff --git a/drivers/mtd/nand/hisi504_nand.c b/drivers/mtd/nand/hisi504_nand.c
>> new file mode 100644
>> index 0000000..2000f21
>> --- /dev/null
>> +++ b/drivers/mtd/nand/hisi504_nand.c
>> @@ -0,0 +1,907 @@
>> +/*
>> + * Hisilicon NAND Flash controller driver
>> + *
>> + * Copyright © 2012-2014 HiSilicon Technologies Co., Ltd.
>> + * http://www.hisilicon.com
>> + *
>> + * Author: Zhou Wang <wangzhou.bry at gmail.com>
>> + * The initial developer of the original code is Zhiyong Cai
>> + * <caizhiyong at huawei.com>
>> + *
>> + * This program is free software; you can redistribute it and/or modify
>> + * it under the terms of the GNU General Public License as published by
>> + * the Free Software Foundation; either version 2 of the License, or
>> + * (at your option) any later version.
>> + *
>> + * This program is distributed in the hope that it will be useful,
>> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
>> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
>> + * GNU General Public License for more details.
>> + */
>> +#include <linux/of.h>
>> +#include <linux/of_mtd.h>
>> +#include <linux/mtd/mtd.h>
>> +#include <linux/sizes.h>
>> +#include <linux/clk.h>
>> +#include <linux/slab.h>
>> +#include <linux/module.h>
>> +#include <linux/delay.h>
>> +#include <linux/interrupt.h>
>> +#include <linux/mtd/nand.h>
>> +#include <linux/dma-mapping.h>
>> +#include <linux/platform_device.h>
>> +#include <linux/mtd/partitions.h>
>> +
>> +#define HINFC504_MAX_CHIP (4)
>> +#define HINFC504_W_LATCH (5)
>> +#define HINFC504_R_LATCH (7)
>> +#define HINFC504_RW_LATCH (3)
>> +
>> +#define HINFC504_NFC_TIMEOUT (2 * HZ)
>> +#define HINFC504_NFC_PM_TIMEOUT (1 * HZ)
>> +#define HINFC504_NFC_DMA_TIMEOUT (5 * HZ)
>> +#define HINFC504_CHIP_DELAY (25)
>> +
>> +#define HINFC504_REG_BASE_ADDRESS_LEN (0x100)
>> +#define HINFC504_BUFFER_BASE_ADDRESS_LEN (2048 + 128)
>> +
>> +#define HINFC504_ADDR_CYCLE_MASK 0x4
>> +
>> +#define HINFC504_CON 0x00
>> +#define HINFC504_CON_OP_MODE_NORMAL BIT(0)
>> +#define HINFC504_CON_PAGEISZE_SHIFT (1)
>> +#define HINFC504_CON_PAGESIZE_MASK (0x07)
>> +#define HINFC504_CON_BUS_WIDTH BIT(4)
>> +#define HINFC504_CON_READY_BUSY_SEL BIT(8)
>> +#define HINFC504_CON_ECCTYPE_SHIFT (9)
>> +#define HINFC504_CON_ECCTYPE_MASK (0x07)
>> +
>> +#define HINFC504_PWIDTH 0x04
>> +#define SET_HINFC504_PWIDTH(_w_lcnt, _r_lcnt, _rw_hcnt) \
>> + ((_w_lcnt) | (((_r_lcnt) & 0x0F) << 4) | (((_rw_hcnt) & 0x0F) << 8))
>> +
>> +#define HINFC504_CMD 0x0C
>> +#define HINFC504_ADDRL 0x10
>> +#define HINFC504_ADDRH 0x14
>> +#define HINFC504_DATA_NUM 0x18
>> +
>> +#define HINFC504_OP 0x1C
>> +#define HINFC504_OP_READ_DATA_EN BIT(1)
>> +#define HINFC504_OP_WAIT_READY_EN BIT(2)
>> +#define HINFC504_OP_CMD2_EN BIT(3)
>> +#define HINFC504_OP_WRITE_DATA_EN BIT(4)
>> +#define HINFC504_OP_ADDR_EN BIT(5)
>> +#define HINFC504_OP_CMD1_EN BIT(6)
>> +#define HINFC504_OP_NF_CS_SHIFT (7)
>> +#define HINFC504_OP_NF_CS_MASK (3)
>> +#define HINFC504_OP_ADDR_CYCLE_SHIFT (9)
>> +#define HINFC504_OP_ADDR_CYCLE_MASK (7)
>> +
>> +#define HINFC504_STATUS 0x20
>> +#define HINFC504_READY BIT(0)
>> +
>> +#define HINFC504_INTEN 0x24
>> +#define HINFC504_INTEN_DMA BIT(9)
>> +#define HINFC504_INTEN_UE BIT(6)
>> +#define HINFC504_INTEN_CE BIT(5)
>> +
>> +#define HINFC504_INTS 0x28
>> +#define HINFC504_INTS_DMA BIT(9)
>> +#define HINFC504_INTS_UE BIT(6)
>> +#define HINFC504_INTS_CE BIT(5)
>> +
>> +#define HINFC504_INTCLR 0x2C
>> +#define HINFC504_INTCLR_DMA BIT(9)
>> +#define HINFC504_INTCLR_UE BIT(6)
>> +#define HINFC504_INTCLR_CE BIT(5)
>> +
>> +#define HINFC504_ECC_STATUS 0x5C
>> +#define HINFC504_ECC_1_BIT_SHIFT 16
>> +#define HINFC504_ECC_16_BIT_SHIFT 12
>> +
>> +#define HINFC504_DMA_CTRL 0x60
>> +#define HINFC504_DMA_CTRL_DMA_START BIT(0)
>> +#define HINFC504_DMA_CTRL_WE BIT(1)
>> +#define HINFC504_DMA_CTRL_DATA_AREA_EN BIT(2)
>> +#define HINFC504_DMA_CTRL_OOB_AREA_EN BIT(3)
>> +#define HINFC504_DMA_CTRL_BURST4_EN BIT(4)
>> +#define HINFC504_DMA_CTRL_BURST8_EN BIT(5)
>> +#define HINFC504_DMA_CTRL_BURST16_EN BIT(6)
>> +#define HINFC504_DMA_CTRL_ADDR_NUM_SHIFT (7)
>> +#define HINFC504_DMA_CTRL_ADDR_NUM_MASK (1)
>> +#define HINFC504_DMA_CTRL_CS_SHIFT (8)
>> +#define HINFC504_DMA_CTRL_CS_MASK (0x03)
>> +
>> +#define HINFC504_DMA_ADDR_DATA 0x64
>> +#define HINFC504_DMA_ADDR_OOB 0x68
>> +
>> +#define HINFC504_DMA_LEN 0x6C
>> +#define HINFC504_DMA_LEN_OOB_SHIFT (16)
>> +#define HINFC504_DMA_LEN_OOB_MASK (0xFFF)
>> +
>> +#define HINFC504_DMA_PARA 0x70
>> +#define HINFC504_DMA_PARA_DATA_RW_EN BIT(0)
>> +#define HINFC504_DMA_PARA_OOB_RW_EN BIT(1)
>> +#define HINFC504_DMA_PARA_DATA_EDC_EN BIT(2)
>> +#define HINFC504_DMA_PARA_OOB_EDC_EN BIT(3)
>> +#define HINFC504_DMA_PARA_DATA_ECC_EN BIT(4)
>> +#define HINFC504_DMA_PARA_OOB_ECC_EN BIT(5)
>> +
>> +#define HINFC_VERSION 0x74
>> +#define HINFC504_LOG_READ_ADDR 0x7C
>> +#define HINFC504_LOG_READ_LEN 0x80
>> +
>> +#define HINFC504_NANDINFO_LEN 0x10
>> +
>> +struct hinfc_host {
>> + struct nand_chip chip;
>> + struct mtd_info mtd;
>> + struct device *dev;
>> + void __iomem *iobase;
>> + struct completion cmd_complete;
>> + unsigned int offset;
>> + unsigned int command;
>> + int chipselect;
>> + unsigned int addr_cycle;
>> + u32 addr_value[2];
>> + u32 cache_addr_value[2];
>> + char *buffer;
>> + dma_addr_t dma_buffer;
>> + dma_addr_t dma_oob;
>> + int version;
>> + unsigned int irq_status; /* interrupt status */
>> +};
>> +
>> +static inline unsigned int hinfc_read(struct hinfc_host *host, unsigned int reg)
>> +{
>> + return readl(host->iobase + reg);
>> +}
>> +
>> +static inline void hinfc_write(struct hinfc_host *host, unsigned int value,
>> + unsigned int reg)
>> +{
>> + writel(value, host->iobase + reg);
>> +}
>> +
>> +static void wait_controller_finished(struct hinfc_host *host)
>> +{
>> + unsigned long timeout = jiffies + HINFC504_NFC_TIMEOUT;
>> + int val;
>> +
>> + while (time_before(jiffies, timeout)) {
>> + val = hinfc_read(host, HINFC504_STATUS);
>> + if (host->command == NAND_CMD_ERASE2) {
>> + /* nfc is ready */
>> + while (!(val & HINFC504_READY)) {
>> + usleep_range(500, 1000);
>> + val = hinfc_read(host, HINFC504_STATUS);
>> + }
>> + return;
>> + }
>> +
>> + if (val & HINFC504_READY)
>> + return;
>> + }
>> +
>> + /* wait cmd timeout */
>> + dev_err(host->dev, "Wait NAND controller exec cmd timeout.\n");
>> +}
>> +
>> +static void hisi_nfc_dma_transfer(struct hinfc_host *host, int todev)
>> +{
>> + struct mtd_info *mtd = &host->mtd;
>> + struct nand_chip *chip = mtd->priv;
>> + unsigned long val;
>> + int ret;
>> +
>> + hinfc_write(host, host->dma_buffer, HINFC504_DMA_ADDR_DATA);
>> + hinfc_write(host, host->dma_oob, HINFC504_DMA_ADDR_OOB);
>> +
>> + if (chip->ecc.mode == NAND_ECC_NONE) {
>> + hinfc_write(host, ((mtd->oobsize & HINFC504_DMA_LEN_OOB_MASK)
>> + << HINFC504_DMA_LEN_OOB_SHIFT), HINFC504_DMA_LEN);
>> +
>> + hinfc_write(host, HINFC504_DMA_PARA_DATA_RW_EN
>> + | HINFC504_DMA_PARA_OOB_RW_EN, HINFC504_DMA_PARA);
>> + } else {
>> + if (host->command == NAND_CMD_READOOB)
>> + hinfc_write(host, HINFC504_DMA_PARA_OOB_RW_EN
>> + | HINFC504_DMA_PARA_OOB_EDC_EN
>> + | HINFC504_DMA_PARA_OOB_ECC_EN, HINFC504_DMA_PARA);
>> + else
>> + hinfc_write(host, HINFC504_DMA_PARA_DATA_RW_EN
>> + | HINFC504_DMA_PARA_OOB_RW_EN
>> + | HINFC504_DMA_PARA_DATA_EDC_EN
>> + | HINFC504_DMA_PARA_OOB_EDC_EN
>> + | HINFC504_DMA_PARA_DATA_ECC_EN
>> + | HINFC504_DMA_PARA_OOB_ECC_EN, HINFC504_DMA_PARA);
>> +
>> + }
>> +
>> + val = (HINFC504_DMA_CTRL_DMA_START | HINFC504_DMA_CTRL_BURST4_EN
>> + | HINFC504_DMA_CTRL_BURST8_EN | HINFC504_DMA_CTRL_BURST16_EN
>> + | HINFC504_DMA_CTRL_DATA_AREA_EN | HINFC504_DMA_CTRL_OOB_AREA_EN
>> + | ((host->addr_cycle == 4 ? 1 : 0)
>> + << HINFC504_DMA_CTRL_ADDR_NUM_SHIFT)
>> + | ((host->chipselect & HINFC504_DMA_CTRL_CS_MASK)
>> + << HINFC504_DMA_CTRL_CS_SHIFT));
>> +
>> + if (todev)
>> + val |= HINFC504_DMA_CTRL_WE;
>> +
>> + init_completion(&host->cmd_complete);
>> +
>> + hinfc_write(host, val, HINFC504_DMA_CTRL);
>> + ret = wait_for_completion_timeout(&host->cmd_complete,
>> + HINFC504_NFC_DMA_TIMEOUT);
>> +
>> + if (!ret) {
>> + dev_err(host->dev, "DMA operation(irq) timeout!\n");
>> + /* sanity check */
>> + val = hinfc_read(host, HINFC504_DMA_CTRL);
>> + if (!(val & HINFC504_DMA_CTRL_DMA_START))
>> + dev_err(host->dev, "DMA is already done but without irq ACK!\n");
>> + else
>> + dev_err(host->dev, "DMA is really timeout!\n");
>> + }
>> +}
>> +
>> +static int hisi_nfc_send_cmd_pageprog(struct hinfc_host *host)
>> +{
>> + host->addr_value[0] &= 0xffff0000;
>> +
>> + hinfc_write(host, host->addr_value[0], HINFC504_ADDRL);
>> + hinfc_write(host, host->addr_value[1], HINFC504_ADDRH);
>> + hinfc_write(host, NAND_CMD_PAGEPROG << 8 | NAND_CMD_SEQIN,
>> + HINFC504_CMD);
>> +
>> + hisi_nfc_dma_transfer(host, 1);
>> +
>> + return 0;
>> +}
>> +
>> +static int hisi_nfc_send_cmd_readstart(struct hinfc_host *host)
>> +{
>> + struct mtd_info *mtd = &host->mtd;
>> +
>> + if ((host->addr_value[0] == host->cache_addr_value[0]) &&
>> + (host->addr_value[1] == host->cache_addr_value[1]))
>> + return 0;
>> +
>> + host->addr_value[0] &= 0xffff0000;
>> +
>> + hinfc_write(host, host->addr_value[0], HINFC504_ADDRL);
>> + hinfc_write(host, host->addr_value[1], HINFC504_ADDRH);
>> + hinfc_write(host, NAND_CMD_READSTART << 8 | NAND_CMD_READ0,
>> + HINFC504_CMD);
>> +
>> + hinfc_write(host, 0, HINFC504_LOG_READ_ADDR);
>> + hinfc_write(host, mtd->writesize + mtd->oobsize,
>> + HINFC504_LOG_READ_LEN);
>> +
>> + hisi_nfc_dma_transfer(host, 0);
>> +
>> + host->cache_addr_value[0] = host->addr_value[0];
>> + host->cache_addr_value[1] = host->addr_value[1];
>> +
>> + return 0;
>> +}
>> +
>> +static int hisi_nfc_send_cmd_erase(struct hinfc_host *host)
>> +{
>> + hinfc_write(host, host->addr_value[0], HINFC504_ADDRL);
>> + hinfc_write(host, (NAND_CMD_ERASE2 << 8) | NAND_CMD_ERASE1,
>> + HINFC504_CMD);
>> +
>> + hinfc_write(host, HINFC504_OP_WAIT_READY_EN
>> + | HINFC504_OP_CMD2_EN
>> + | HINFC504_OP_CMD1_EN
>> + | HINFC504_OP_ADDR_EN
>> + | ((host->chipselect & HINFC504_OP_NF_CS_MASK)
>> + << HINFC504_OP_NF_CS_SHIFT)
>> + | ((host->addr_cycle & HINFC504_OP_ADDR_CYCLE_MASK)
>> + << HINFC504_OP_ADDR_CYCLE_SHIFT),
>> + HINFC504_OP);
>> +
>> + wait_controller_finished(host);
>> +
>> + return 0;
>> +}
>> +
>> +static int hisi_nfc_send_cmd_readid(struct hinfc_host *host)
>> +{
>> + hinfc_write(host, HINFC504_NANDINFO_LEN, HINFC504_DATA_NUM);
>> + hinfc_write(host, NAND_CMD_READID, HINFC504_CMD);
>> + hinfc_write(host, 0, HINFC504_ADDRL);
>> +
>> + hinfc_write(host, HINFC504_OP_CMD1_EN | HINFC504_OP_ADDR_EN
>> + | HINFC504_OP_READ_DATA_EN
>> + | ((host->chipselect & HINFC504_OP_NF_CS_MASK)
>> + << HINFC504_OP_NF_CS_SHIFT)
>> + | 1 << HINFC504_OP_ADDR_CYCLE_SHIFT, HINFC504_OP);
>> +
>> + wait_controller_finished(host);
>> +
>> + return 0;
>> +}
>> +
>> +static int hisi_nfc_send_cmd_status(struct hinfc_host *host)
>> +{
>> + hinfc_write(host, HINFC504_NANDINFO_LEN, HINFC504_DATA_NUM);
>> + hinfc_write(host, NAND_CMD_STATUS, HINFC504_CMD);
>> + hinfc_write(host, HINFC504_OP_CMD1_EN
>> + | HINFC504_OP_READ_DATA_EN
>> + | ((host->chipselect & HINFC504_OP_NF_CS_MASK)
>> + << HINFC504_OP_NF_CS_SHIFT),
>> + HINFC504_OP);
>> +
>> + wait_controller_finished(host);
>> +
>> + return 0;
>> +}
>> +
>> +static int hisi_nfc_send_cmd_reset(struct hinfc_host *host, int chipselect)
>> +{
>> + hinfc_write(host, NAND_CMD_RESET, HINFC504_CMD);
>> +
>> + hinfc_write(host, HINFC504_OP_CMD1_EN
>> + | ((chipselect & HINFC504_OP_NF_CS_MASK)
>> + << HINFC504_OP_NF_CS_SHIFT)
>> + | HINFC504_OP_WAIT_READY_EN,
>> + HINFC504_OP);
>> +
>> + wait_controller_finished(host);
>> +
>> + return 0;
>> +}
>> +
>> +static void hisi_nfc_select_chip(struct mtd_info *mtd, int chipselect)
>> +{
>> + struct nand_chip *chip = mtd->priv;
>> + struct hinfc_host *host = chip->priv;
>> +
>> + if (chipselect < 0)
>> + return;
>> +
>> + host->chipselect = chipselect;
>> +}
>> +
>> +static uint8_t hisi_nfc_read_byte(struct mtd_info *mtd)
>> +{
>> + struct nand_chip *chip = mtd->priv;
>> + struct hinfc_host *host = chip->priv;
>> +
>> + if (host->command == NAND_CMD_STATUS)
>> + return readb(chip->IO_ADDR_R);
>> +
>> + host->offset++;
>> +
>> + if (host->command == NAND_CMD_READID)
>> + return readb(chip->IO_ADDR_R + host->offset - 1);
>> +
>> + return readb(host->buffer + host->offset - 1);
>
> You're reading from memory, not IO. You don't need readb().
Yes, I will get the value directly. Thanks!
>
>> +}
>> +
>> +static u16 hisi_nfc_read_word(struct mtd_info *mtd)
>> +{
>> + struct nand_chip *chip = mtd->priv;
>> + struct hinfc_host *host = chip->priv;
>> +
>> + host->offset += 2;
>> + return readw(host->buffer + host->offset - 2);
>
> Same here, for readw().
Thanks!
>
>> +}
>> +
>> +static void
>> +hisi_nfc_write_buf(struct mtd_info *mtd, const uint8_t *buf, int len)
>> +{
>> + struct nand_chip *chip = mtd->priv;
>> + struct hinfc_host *host = chip->priv;
>> +
>> + memcpy(host->buffer + host->offset, buf, len);
>> + host->offset += len;
>> +}
>> +
>> +static void hisi_nfc_read_buf(struct mtd_info *mtd, uint8_t *buf, int len)
>> +{
>> + struct nand_chip *chip = mtd->priv;
>> + struct hinfc_host *host = chip->priv;
>> +
>> + memcpy(buf, host->buffer + host->offset, len);
>> + host->offset += len;
>> +}
>> +
>> +static void set_addr(struct mtd_info *mtd, int column, int page_addr)
>> +{
>> + struct nand_chip *chip = mtd->priv;
>> + struct hinfc_host *host = chip->priv;
>> + unsigned int command = host->command;
>> +
>> + host->addr_cycle = 0;
>> + host->addr_value[0] = 0;
>> + host->addr_value[1] = 0;
>> +
>> + /* Serially input address */
>> + if (column != -1) {
>> + /* Adjust columns for 16 bit buswidth */
>> + if (chip->options & NAND_BUSWIDTH_16 &&
>> + !nand_opcode_8bits(command))
>> + column >>= 1;
>> +
>> + host->addr_value[0] = column & 0xffff;
>> + host->addr_cycle = 2;
>> + }
>> + if (page_addr != -1) {
>> + host->addr_value[0] |= (page_addr & 0xffff)
>> + << (host->addr_cycle * 8);
>> + host->addr_cycle += 2;
>> + /* One more address cycle for devices > 128MiB */
>> + if (chip->chipsize > (128 << 20)) {
>> + host->addr_cycle += 1;
>> + if (host->command == NAND_CMD_ERASE1)
>> + host->addr_value[0] |= ((page_addr >> 16) & 0xff) << 16;
>> + else
>> + host->addr_value[1] |= ((page_addr >> 16) & 0xff);
>> + }
>> + }
>> +}
>> +
>> +static void hisi_nfc_cmdfunc(struct mtd_info *mtd, unsigned command, int column,
>> + int page_addr)
>> +{
>> + struct nand_chip *chip = mtd->priv;
>> + struct hinfc_host *host = chip->priv;
>> + int is_cache_invalid = 1;
>> + unsigned int flag = 0;
>> +
>> + host->command = command;
>> +
>> + switch (command) {
>> + case NAND_CMD_READ0:
>> + case NAND_CMD_READOOB:
>> + if (command == NAND_CMD_READ0)
>> + host->offset = column;
>> + else
>> + host->offset = column + mtd->writesize;
>> +
>> + is_cache_invalid = 0;
>> + set_addr(mtd, column, page_addr);
>> + hisi_nfc_send_cmd_readstart(host);
>> + break;
>> +
>> + case NAND_CMD_SEQIN:
>> + host->offset = column;
>> + set_addr(mtd, column, page_addr);
>> + break;
>> +
>> + case NAND_CMD_ERASE1:
>> + set_addr(mtd, column, page_addr);
>> + break;
>> +
>> + case NAND_CMD_PAGEPROG:
>> + hisi_nfc_send_cmd_pageprog(host);
>> + break;
>> +
>> + case NAND_CMD_ERASE2:
>> + hisi_nfc_send_cmd_erase(host);
>> + break;
>> +
>> + case NAND_CMD_READID:
>> + host->offset = column;
>> + memset(chip->IO_ADDR_R, 0, 0x10);
>> + hisi_nfc_send_cmd_readid(host);
>> + break;
>> +
>> + case NAND_CMD_STATUS:
>> + flag = hinfc_read(host, HINFC504_CON);
>> + if (chip->ecc.mode == NAND_ECC_HW)
>> + hinfc_write(host,
>> + flag && ~(HINFC504_CON_ECCTYPE_MASK <<
>> + HINFC504_CON_ECCTYPE_SHIFT), HINFC504_CON);
>> +
>> + host->offset = 0;
>> + memset(chip->IO_ADDR_R, 0, 0x10);
>> + hisi_nfc_send_cmd_status(host);
>> + hinfc_write(host, flag, HINFC504_CON);
>> + break;
>> +
>> + case NAND_CMD_RESET:
>> + hisi_nfc_send_cmd_reset(host, host->chipselect);
>> + break;
>> +
>> + default:
>> + dev_err(host->dev, "Error: unsupported cmd(cmd=%x, col=%x, page=%x)\n",
>> + command, column, page_addr);
>> + }
>> +
>> + if (is_cache_invalid) {
>> + host->cache_addr_value[0] = ~0;
>> + host->cache_addr_value[1] = ~0;
>> + }
>> +}
>> +
>> +static irqreturn_t hinfc_irq_handle(int irq, void *devid)
>> +{
>> + struct hinfc_host *host = devid;
>> + unsigned int flag;
>> +
>> + flag = hinfc_read(host, HINFC504_INTS);
>> + /* store interrupts state */
>> + host->irq_status |= flag;
>> +
>> + if (flag & HINFC504_INTS_DMA) {
>> + hinfc_write(host, HINFC504_INTCLR_DMA, HINFC504_INTCLR);
>> + complete(&host->cmd_complete);
>> + } else if (flag & HINFC504_INTS_CE) {
>> + hinfc_write(host, HINFC504_INTCLR_CE, HINFC504_INTCLR);
>> + } else if (flag & HINFC504_INTS_UE) {
>> + hinfc_write(host, HINFC504_INTCLR_UE, HINFC504_INTCLR);
>> + }
>> +
>> + return IRQ_HANDLED;
>> +}
>> +
>> +static int hisi_nand_read_page_hwecc(struct mtd_info *mtd,
>> + struct nand_chip *chip, uint8_t *buf, int oob_required, int page)
>> +{
>> + struct hinfc_host *host = chip->priv;
>> + int max_bitflips = 0, stat = 0, stat_max, status_ecc;
>> + int stat_1, stat_2;
>> +
>> + chip->read_buf(mtd, buf, mtd->writesize);
>> + chip->read_buf(mtd, chip->oob_poi, mtd->oobsize);
>> +
>> + /* errors which can not be corrected by ECC */
>> + if (host->irq_status & HINFC504_INTS_UE) {
>> + mtd->ecc_stats.failed++;
>> + } else if (host->irq_status & HINFC504_INTS_CE) {
>> + /* TODO: need add other ECC modes! */
>> + switch (chip->ecc.strength) {
>> + case 1:
>> + stat = hweight8(hinfc_read(host, HINFC504_ECC_STATUS)>>
>> + HINFC504_ECC_1_BIT_SHIFT);
>> + stat_max = 1;
>> + break;
>> + case 16:
>> + status_ecc = hinfc_read(host, HINFC504_ECC_STATUS) >>
>> + HINFC504_ECC_16_BIT_SHIFT & 0x0fff;
>> + stat_2 = status_ecc & 0x3f;
>> + stat_1 = status_ecc >> 6 & 0x3f;
>> + stat = stat_1 + stat_2;
>> + stat_max = max_t(int, stat_1, stat_2);
>> + }
>> + mtd->ecc_stats.corrected += stat;
>> + max_bitflips = max_t(int, max_bitflips, stat_max);
>> + }
>> + host->irq_status = 0;
>> +
>> + return max_bitflips;
>> +}
>> +
>> +static int hisi_nand_read_oob(struct mtd_info *mtd, struct nand_chip *chip,
>> + int page)
>> +{
>> + struct hinfc_host *host = chip->priv;
>> +
>> + chip->cmdfunc(mtd, NAND_CMD_READOOB, 0, page);
>> + chip->read_buf(mtd, chip->oob_poi, mtd->oobsize);
>> +
>> + if (host->irq_status & HINFC504_INTS_UE) {
>> + host->irq_status = 0;
>> + return -EBADMSG;
>> + }
>> +
>> + host->irq_status = 0;
>> + return 0;
>> +}
>> +
>> +static int hisi_nand_write_page_hwecc(struct mtd_info *mtd,
>> + struct nand_chip *chip, const uint8_t *buf, int oob_required)
>> +{
>> + chip->write_buf(mtd, buf, mtd->writesize);
>> + if (oob_required)
>> + chip->write_buf(mtd, chip->oob_poi, mtd->oobsize);
>> +
>> + return 0;
>> +}
>> +
>> +static void hisi_nfc_host_init(struct hinfc_host *host)
>> +{
>> + struct nand_chip *chip = &host->chip;
>> + unsigned int flag = 0;
>> +
>> + host->version = hinfc_read(host, HINFC_VERSION);
>> + host->addr_cycle = 0;
>> + host->addr_value[0] = 0;
>> + host->addr_value[1] = 0;
>> + host->cache_addr_value[0] = ~0;
>> + host->cache_addr_value[1] = ~0;
>> + host->chipselect = 0;
>> +
>> + /* default page size: 2K, ecc_none. need modify */
>> + flag = HINFC504_CON_OP_MODE_NORMAL | HINFC504_CON_READY_BUSY_SEL
>> + | ((0x001 & HINFC504_CON_PAGESIZE_MASK)
>> + << HINFC504_CON_PAGEISZE_SHIFT)
>> + | ((0x0 & HINFC504_CON_ECCTYPE_MASK)
>> + << HINFC504_CON_ECCTYPE_SHIFT)
>> + | ((chip->options & NAND_BUSWIDTH_16) ?
>> + HINFC504_CON_BUS_WIDTH : 0);
>> + hinfc_write(host, flag, HINFC504_CON);
>> +
>> + memset(chip->IO_ADDR_R, 0xff, HINFC504_BUFFER_BASE_ADDRESS_LEN);
>> +
>> + hinfc_write(host, SET_HINFC504_PWIDTH(HINFC504_W_LATCH,
>> + HINFC504_R_LATCH, HINFC504_RW_LATCH), HINFC504_PWIDTH);
>> +
>> + /* enable DMA irq */
>> + hinfc_write(host, HINFC504_INTEN_DMA, HINFC504_INTEN);
>> +}
>> +
>> +static struct nand_ecclayout nand_ecc_2K_1bit = {
>> + .oobfree = { {24, 40} }
>> +};
>> +
>> +static struct nand_ecclayout nand_ecc_2K_16bits = {
>> + .oobavail = 6,
>> + .oobfree = { {2, 6} },
>> +};
>> +
>> +static int hisi_nfc_ecc_probe(struct hinfc_host *host)
>> +{
>> + unsigned int flag;
>> + int size, strength, ecc_bits;
>> + struct device *dev = host->dev;
>> + struct nand_chip *chip = &host->chip;
>> + struct mtd_info *mtd = &host->mtd;
>> + struct device_node *np = host->dev->of_node;
>> +
>> + size = of_get_nand_ecc_step_size(np);
>> + strength = of_get_nand_ecc_strength(np);
>> + if ((size != 512) && (size != 1024)) {
>> + dev_err(dev, "error ecc size: %d\n", size);
>> + return -EINVAL;
>> + }
>> +
>> + if ((size == 512) && (strength != 1)) {
>> + dev_err(dev, "ecc size and strength do not match\n");
>> + return -EINVAL;
>> + }
>> + if ((size == 1024) && ((strength != 8) && (strength != 16) &&
>> + (strength != 24) && (strength != 40))) {
>> + dev_err(dev, "ecc size and strength do not match\n");
>> + return -EINVAL;
>> + }
>> +
>> + chip->ecc.size = size;
>> + chip->ecc.strength = strength;
>> +
>> + chip->ecc.read_page = hisi_nand_read_page_hwecc;
>> + chip->ecc.read_oob = hisi_nand_read_oob;
>> + chip->ecc.write_page = hisi_nand_write_page_hwecc;
>> +
>> + switch (chip->ecc.strength) {
>> + case 1:
>> + ecc_bits = 1;
>> + if (mtd->writesize == 2048)
>> + chip->ecc.layout = &nand_ecc_2K_1bit;
>> +
>> + /* TODO: add more page size support */
>> + break;
>> + case 16:
>> + ecc_bits = 6;
>> + if (mtd->writesize == 2048)
>> + chip->ecc.layout = &nand_ecc_2K_16bits;
>> +
>> + /* TODO: add more page size support */
>> + break;
>> +
>> + /* TODO: add more ecc strength support */
>> + default:
>> + dev_err(dev, "not support strength: %d\n", chip->ecc.strength);
>> + return -EINVAL;
>> + }
>> +
>> + flag = hinfc_read(host, HINFC504_CON);
>> + /* add ecc type configure */
>> + flag |= ((ecc_bits & HINFC504_CON_ECCTYPE_MASK)
>> + << HINFC504_CON_ECCTYPE_SHIFT);
>> + hinfc_write(host, flag, HINFC504_CON);
>> +
>> + /* enable ecc irq */
>> + flag = hinfc_read(host, HINFC504_INTEN) & 0xfff;
>> + hinfc_write(host, flag | HINFC504_INTEN_UE | HINFC504_INTEN_CE,
>> + HINFC504_INTEN);
>> +
>> + return 0;
>> +}
>> +
>> +static int hisi_nfc_probe(struct platform_device *pdev)
>> +{
>> + int ret = 0, irq, buswidth, flag, max_chips = HINFC504_MAX_CHIP;
>> + struct device *dev = &pdev->dev;
>> + struct hinfc_host *host;
>> + struct nand_chip *chip;
>> + struct mtd_info *mtd;
>> + struct resource *res;
>> + struct device_node *np = dev->of_node;
>> + struct mtd_part_parser_data ppdata;
>> +
>> + host = devm_kzalloc(dev, sizeof(*host), GFP_KERNEL);
>> + if (!host)
>> + return -ENOMEM;
>> + host->dev = dev;
>> +
>> + platform_set_drvdata(pdev, host);
>> + chip = &host->chip;
>> + mtd = &host->mtd;
>> +
>> + irq = platform_get_irq(pdev, 0);
>> + if (irq < 0) {
>> + dev_err(dev, "no IRQ resource defined\n");
>> + ret = -ENXIO;
>> + goto err_res;
>> + }
>> +
>> + res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
>> + host->iobase = devm_ioremap_resource(dev, res);
>> + if (IS_ERR(host->iobase)) {
>> + ret = PTR_ERR(host->iobase);
>> + dev_err(dev, "devm_ioremap_resource[0] fail\n");
>
> I don't think yhou really need this error print. devm_ioremap_resource()
> should be descriptive enough, I think.
Will delete the error print here, thanks!
>
>> + goto err_res;
>> + }
>> +
>> + res = platform_get_resource(pdev, IORESOURCE_MEM, 1);
>> + chip->IO_ADDR_R = chip->IO_ADDR_W = devm_ioremap_resource(dev, res);
>
> Hmm, do you really have to reuse IO_ADDR_{R,W} here? Those are only
> targeted for NAND systems which have a direct MMIO mapping to the NAND
> I/O pins. See nand_base's {read,write}_buf() and read_{byte,word}()
> implementations. But you override those.
There is a hardware buffer in this NAND controller, and the buffer can be
accessed as MMIO. IO_ADDR_R/W just indicates the base address of this buffer.
Maybe I need to use a void __iomem pointer stored in my host struct to use
this buffer instead of IO_ADDR_R/W as you said below here?
>
> It's best if it's obvious if nand_base is somehow inadvertently using
> these pointers. So leaving them NULL is helpful.
>
> As an alternative, you can just stash another private void __iomem
> pointer in you your host struct.
>
>> + if (IS_ERR(chip->IO_ADDR_R)) {
>> + ret = PTR_ERR(chip->IO_ADDR_R);
>> + dev_err(dev, "devm_ioremap_resource[1] fail\n");
>> + goto err_res;
>> + }
>> +
>> + mtd->priv = chip;
>> + mtd->owner = THIS_MODULE;
>> + mtd->name = "hisi_nand";
>> + mtd->dev.parent = &pdev->dev;
>> +
>> + chip->priv = host;
>> + chip->cmdfunc = hisi_nfc_cmdfunc;
>> + chip->select_chip = hisi_nfc_select_chip;
>> + chip->read_byte = hisi_nfc_read_byte;
>> + chip->read_word = hisi_nfc_read_word;
>> + chip->write_buf = hisi_nfc_write_buf;
>> + chip->read_buf = hisi_nfc_read_buf;
>> + chip->chip_delay = HINFC504_CHIP_DELAY;
>> +
>> + chip->ecc.mode = of_get_nand_ecc_mode(np);
>> +
>> + buswidth = of_get_nand_bus_width(np);
>> + if (buswidth == 16)
>> + chip->options |= NAND_BUSWIDTH_16;
>> +
>> + hisi_nfc_host_init(host);
>> +
>> + ret = devm_request_irq(dev, irq, hinfc_irq_handle, IRQF_DISABLED,
>> + "nandc", host);
>> + if (ret) {
>> + dev_err(dev, "failed to request IRQ\n");
>> + goto err_res;
>> + }
>> +
>> + ret = nand_scan_ident(mtd, max_chips, NULL);
>> + if (ret) {
>> + ret = -ENODEV;
>> + goto err_res;
>> + }
>> +
>> + host->buffer = dmam_alloc_coherent(dev, mtd->writesize + mtd->oobsize,
>> + &host->dma_buffer, GFP_KERNEL);
>
> You need to check this for allocation failures.
>
Will add relative code to check this, thanks!
>> + host->dma_oob = host->dma_buffer + mtd->writesize;
>> + memset(host->buffer, 0xff, mtd->writesize + mtd->oobsize);
>> +
>> + flag = hinfc_read(host, HINFC504_CON);
>> + flag &= ~(HINFC504_CON_PAGESIZE_MASK << HINFC504_CON_PAGEISZE_SHIFT);
>> + switch (mtd->writesize) {
>> + case 2048:
>> + flag |= (0x001 << HINFC504_CON_PAGEISZE_SHIFT); break;
>> + /*
>> + * TODO: add more pagesize support,
>> + * default pagesize has been set in hisi_nfc_host_init
>> + */
>> + default:
>> + dev_err(dev, "NON-2KB page size nand flash\n");
>> + ret = -EINVAL;
>> + goto err_res;
>> + }
>> + hinfc_write(host, flag, HINFC504_CON);
>> +
>> + if (chip->ecc.mode == NAND_ECC_HW)
>> + hisi_nfc_ecc_probe(host);
>> +
>> + ret = nand_scan_tail(mtd);
>> + if (ret) {
>> + dev_err(dev, "nand_scan_tail failed: %d\n", ret);
>> + goto err_res;
>> + }
>> +
>> + ppdata.of_node = np;
>> + ret = mtd_device_parse_register(mtd, NULL, &ppdata, NULL, 0);
>> + if (ret) {
>> + dev_err(dev, "Err MTD partition=%d\n", ret);
>> + goto err_mtd;
>> + }
>> +
>> + return 0;
>> +
>> +err_mtd:
>> + nand_release(mtd);
>> +err_res:
>> + return ret;
>> +}
>> +
>> +static int hisi_nfc_remove(struct platform_device *pdev)
>> +{
>> + struct hinfc_host *host = platform_get_drvdata(pdev);
>> + struct mtd_info *mtd = &host->mtd;
>> +
>> + nand_release(mtd);
>> +
>> + return 0;
>> +}
>> +
>> +#ifdef CONFIG_PM_SLEEP
>> +static int hisi_nfc_suspend(struct device *dev)
>> +{
>> + struct hinfc_host *host = dev_get_drvdata(dev);
>> + unsigned long timeout = jiffies + HINFC504_NFC_PM_TIMEOUT;
>> +
>> + while (time_before(jiffies, timeout)) {
>> + if (((hinfc_read(host, HINFC504_STATUS) & 0x1) == 0x0) &&
>> + (hinfc_read(host, HINFC504_DMA_CTRL) &
>> + HINFC504_DMA_CTRL_DMA_START)) {
>> + _cond_resched();
>
> Why not just cond_resched()?
>
It is better to just use cond_resched(), will modify this. Thanks!
>> + return 0;
>> + }
>> + }
>> +
>> + dev_err(host->dev, "nand controller suspend timeout.\n");
>> +
>> + return -EAGAIN;
>> +}
>> +
>> +static int hisi_nfc_resume(struct device *dev)
>> +{
>> + int cs;
>> + struct hinfc_host *host = dev_get_drvdata(dev);
>> + struct nand_chip *chip = &host->chip;
>> +
>> + for (cs = 0; cs < chip->numchips; cs++)
>> + hisi_nfc_send_cmd_reset(host, cs);
>> + hinfc_write(host, SET_HINFC504_PWIDTH(HINFC504_W_LATCH,
>> + HINFC504_R_LATCH, HINFC504_RW_LATCH), HINFC504_PWIDTH);
>> +
>> + return 0;
>> +}
>> +#endif
>> +static SIMPLE_DEV_PM_OPS(hisi_nfc_pm_ops, hisi_nfc_suspend, hisi_nfc_resume);
>> +
>> +static const struct of_device_id nfc_id_table[] = {
>> + { .compatible = "hisilicon,504-nfc" },
>> + {}
>> +};
>> +MODULE_DEVICE_TABLE(of, nfc_id_table);
>> +
>> +static struct platform_driver hisi_nfc_driver = {
>> + .driver = {
>> + .name = "hisi_nand",
>> + .of_match_table = of_match_ptr(nfc_id_table),
>> + .pm = &hisi_nfc_pm_ops,
>> + },
>> + .probe = hisi_nfc_probe,
>> + .remove = hisi_nfc_remove,
>> +};
>> +
>> +module_platform_driver(hisi_nfc_driver);
>> +
>> +MODULE_LICENSE("GPL");
>> +MODULE_AUTHOR("Zhiyong Cai");
>> +MODULE_AUTHOR("Zhou Wang");
>> +MODULE_DESCRIPTION("Hisilicon Nand Flash Controller Driver");
>
> Brian
Thanks again for your comments.
Zhou Wang
>
> .
>
More information about the linux-arm-kernel
mailing list