[PATCH v6 1/2] mtd: hisilicon: add a new NAND controller driver for hisilicon hip04 Soc

Brian Norris computersforpeace at gmail.com
Mon Jan 12 19:58:44 PST 2015


On Mon, Jan 12, 2015 at 03:28:53PM +0800, Zhou Wang wrote:
> Signed-off-by: Zhou Wang <wangzhou1 at hisilicon.com>

Mostly good. A few small comments.

> ---
>  drivers/mtd/nand/Kconfig        |   5 +
>  drivers/mtd/nand/Makefile       |   1 +
>  drivers/mtd/nand/hisi504_nand.c | 907 ++++++++++++++++++++++++++++++++++++++++
>  3 files changed, 913 insertions(+)
>  create mode 100644 drivers/mtd/nand/hisi504_nand.c
> 
> diff --git a/drivers/mtd/nand/Kconfig b/drivers/mtd/nand/Kconfig
> index 7d0150d..e1220fc 100644
> --- a/drivers/mtd/nand/Kconfig
> +++ b/drivers/mtd/nand/Kconfig
> @@ -524,4 +524,9 @@ config MTD_NAND_SUNXI
>  	help
>  	  Enables support for NAND Flash chips on Allwinner SoCs.
>  
> +config MTD_NAND_HISI504
> +	tristate "Support for NAND controller on Hisilicon SoC Hip04"
> +	help
> +	  Enables support for NAND controller on Hisilicon SoC Hip04.
> +
>  endif # MTD_NAND
> diff --git a/drivers/mtd/nand/Makefile b/drivers/mtd/nand/Makefile
> index bd38f21..582bbd05 100644
> --- a/drivers/mtd/nand/Makefile
> +++ b/drivers/mtd/nand/Makefile
> @@ -51,5 +51,6 @@ obj-$(CONFIG_MTD_NAND_GPMI_NAND)	+= gpmi-nand/
>  obj-$(CONFIG_MTD_NAND_XWAY)		+= xway_nand.o
>  obj-$(CONFIG_MTD_NAND_BCM47XXNFLASH)	+= bcm47xxnflash/
>  obj-$(CONFIG_MTD_NAND_SUNXI)		+= sunxi_nand.o
> +obj-$(CONFIG_MTD_NAND_HISI504)	        += hisi504_nand.o
>  
>  nand-objs := nand_base.o nand_bbt.o nand_timings.o
> diff --git a/drivers/mtd/nand/hisi504_nand.c b/drivers/mtd/nand/hisi504_nand.c
> new file mode 100644
> index 0000000..2000f21
> --- /dev/null
> +++ b/drivers/mtd/nand/hisi504_nand.c
> @@ -0,0 +1,907 @@
> +/*
> + * Hisilicon NAND Flash controller driver
> + *
> + * Copyright © 2012-2014 HiSilicon Technologies Co., Ltd.
> + *              http://www.hisilicon.com
> + *
> + * Author: Zhou Wang <wangzhou.bry at gmail.com>
> + * The initial developer of the original code is Zhiyong Cai
> + * <caizhiyong at huawei.com>
> + *
> + * This program is free software; you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License as published by
> + * the Free Software Foundation; either version 2 of the License, or
> + * (at your option) any later version.
> + *
> + * This program is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
> + * GNU General Public License for more details.
> + */
> +#include <linux/of.h>
> +#include <linux/of_mtd.h>
> +#include <linux/mtd/mtd.h>
> +#include <linux/sizes.h>
> +#include <linux/clk.h>
> +#include <linux/slab.h>
> +#include <linux/module.h>
> +#include <linux/delay.h>
> +#include <linux/interrupt.h>
> +#include <linux/mtd/nand.h>
> +#include <linux/dma-mapping.h>
> +#include <linux/platform_device.h>
> +#include <linux/mtd/partitions.h>
> +
> +#define HINFC504_MAX_CHIP                               (4)
> +#define HINFC504_W_LATCH                                (5)
> +#define HINFC504_R_LATCH                                (7)
> +#define HINFC504_RW_LATCH                               (3)
> +
> +#define HINFC504_NFC_TIMEOUT				(2 * HZ)
> +#define HINFC504_NFC_PM_TIMEOUT				(1 * HZ)
> +#define HINFC504_NFC_DMA_TIMEOUT			(5 * HZ)
> +#define HINFC504_CHIP_DELAY				(25)
> +
> +#define HINFC504_REG_BASE_ADDRESS_LEN			(0x100)
> +#define HINFC504_BUFFER_BASE_ADDRESS_LEN		(2048 + 128)
> +
> +#define HINFC504_ADDR_CYCLE_MASK			0x4
> +
> +#define HINFC504_CON					0x00
> +#define HINFC504_CON_OP_MODE_NORMAL			BIT(0)
> +#define HINFC504_CON_PAGEISZE_SHIFT			(1)
> +#define HINFC504_CON_PAGESIZE_MASK			(0x07)
> +#define HINFC504_CON_BUS_WIDTH				BIT(4)
> +#define HINFC504_CON_READY_BUSY_SEL			BIT(8)
> +#define HINFC504_CON_ECCTYPE_SHIFT			(9)
> +#define HINFC504_CON_ECCTYPE_MASK			(0x07)
> +
> +#define HINFC504_PWIDTH					0x04
> +#define SET_HINFC504_PWIDTH(_w_lcnt, _r_lcnt, _rw_hcnt) \
> +	((_w_lcnt) | (((_r_lcnt) & 0x0F) << 4) | (((_rw_hcnt) & 0x0F) << 8))
> +
> +#define HINFC504_CMD					0x0C
> +#define HINFC504_ADDRL					0x10
> +#define HINFC504_ADDRH					0x14
> +#define HINFC504_DATA_NUM				0x18
> +
> +#define HINFC504_OP					0x1C
> +#define HINFC504_OP_READ_DATA_EN			BIT(1)
> +#define HINFC504_OP_WAIT_READY_EN			BIT(2)
> +#define HINFC504_OP_CMD2_EN				BIT(3)
> +#define HINFC504_OP_WRITE_DATA_EN			BIT(4)
> +#define HINFC504_OP_ADDR_EN				BIT(5)
> +#define HINFC504_OP_CMD1_EN				BIT(6)
> +#define HINFC504_OP_NF_CS_SHIFT                         (7)
> +#define HINFC504_OP_NF_CS_MASK				(3)
> +#define HINFC504_OP_ADDR_CYCLE_SHIFT			(9)
> +#define HINFC504_OP_ADDR_CYCLE_MASK			(7)
> +
> +#define HINFC504_STATUS                                 0x20
> +#define HINFC504_READY					BIT(0)
> +
> +#define HINFC504_INTEN					0x24
> +#define HINFC504_INTEN_DMA				BIT(9)
> +#define HINFC504_INTEN_UE				BIT(6)
> +#define HINFC504_INTEN_CE				BIT(5)
> +
> +#define HINFC504_INTS					0x28
> +#define HINFC504_INTS_DMA				BIT(9)
> +#define HINFC504_INTS_UE				BIT(6)
> +#define HINFC504_INTS_CE				BIT(5)
> +
> +#define HINFC504_INTCLR                                 0x2C
> +#define HINFC504_INTCLR_DMA				BIT(9)
> +#define HINFC504_INTCLR_UE				BIT(6)
> +#define HINFC504_INTCLR_CE				BIT(5)
> +
> +#define HINFC504_ECC_STATUS                             0x5C
> +#define HINFC504_ECC_1_BIT_SHIFT                        16
> +#define HINFC504_ECC_16_BIT_SHIFT                       12
> +
> +#define HINFC504_DMA_CTRL				0x60
> +#define HINFC504_DMA_CTRL_DMA_START			BIT(0)
> +#define HINFC504_DMA_CTRL_WE				BIT(1)
> +#define HINFC504_DMA_CTRL_DATA_AREA_EN			BIT(2)
> +#define HINFC504_DMA_CTRL_OOB_AREA_EN			BIT(3)
> +#define HINFC504_DMA_CTRL_BURST4_EN			BIT(4)
> +#define HINFC504_DMA_CTRL_BURST8_EN			BIT(5)
> +#define HINFC504_DMA_CTRL_BURST16_EN			BIT(6)
> +#define HINFC504_DMA_CTRL_ADDR_NUM_SHIFT		(7)
> +#define HINFC504_DMA_CTRL_ADDR_NUM_MASK                 (1)
> +#define HINFC504_DMA_CTRL_CS_SHIFT			(8)
> +#define HINFC504_DMA_CTRL_CS_MASK			(0x03)
> +
> +#define HINFC504_DMA_ADDR_DATA				0x64
> +#define HINFC504_DMA_ADDR_OOB				0x68
> +
> +#define HINFC504_DMA_LEN				0x6C
> +#define HINFC504_DMA_LEN_OOB_SHIFT			(16)
> +#define HINFC504_DMA_LEN_OOB_MASK			(0xFFF)
> +
> +#define HINFC504_DMA_PARA				0x70
> +#define HINFC504_DMA_PARA_DATA_RW_EN			BIT(0)
> +#define HINFC504_DMA_PARA_OOB_RW_EN			BIT(1)
> +#define HINFC504_DMA_PARA_DATA_EDC_EN			BIT(2)
> +#define HINFC504_DMA_PARA_OOB_EDC_EN			BIT(3)
> +#define HINFC504_DMA_PARA_DATA_ECC_EN			BIT(4)
> +#define HINFC504_DMA_PARA_OOB_ECC_EN			BIT(5)
> +
> +#define HINFC_VERSION                                   0x74
> +#define HINFC504_LOG_READ_ADDR				0x7C
> +#define HINFC504_LOG_READ_LEN				0x80
> +
> +#define HINFC504_NANDINFO_LEN				0x10
> +
> +struct hinfc_host {
> +	struct nand_chip	chip;
> +	struct mtd_info		mtd;
> +	struct device		*dev;
> +	void __iomem		*iobase;
> +	struct completion       cmd_complete;
> +	unsigned int		offset;
> +	unsigned int		command;
> +	int			chipselect;
> +	unsigned int		addr_cycle;
> +	u32                     addr_value[2];
> +	u32                     cache_addr_value[2];
> +	char			*buffer;
> +	dma_addr_t		dma_buffer;
> +	dma_addr_t		dma_oob;
> +	int			version;
> +	unsigned int            irq_status; /* interrupt status */
> +};
> +
> +static inline unsigned int hinfc_read(struct hinfc_host *host, unsigned int reg)
> +{
> +	return readl(host->iobase + reg);
> +}
> +
> +static inline void hinfc_write(struct hinfc_host *host, unsigned int value,
> +			       unsigned int reg)
> +{
> +	writel(value, host->iobase + reg);
> +}
> +
> +static void wait_controller_finished(struct hinfc_host *host)
> +{
> +	unsigned long timeout = jiffies + HINFC504_NFC_TIMEOUT;
> +	int val;
> +
> +	while (time_before(jiffies, timeout)) {
> +		val = hinfc_read(host, HINFC504_STATUS);
> +		if (host->command == NAND_CMD_ERASE2) {
> +			/* nfc is ready */
> +			while (!(val & HINFC504_READY))	{
> +				usleep_range(500, 1000);
> +				val = hinfc_read(host, HINFC504_STATUS);
> +			}
> +			return;
> +		}
> +
> +		if (val & HINFC504_READY)
> +			return;
> +	}
> +
> +	/* wait cmd timeout */
> +	dev_err(host->dev, "Wait NAND controller exec cmd timeout.\n");
> +}
> +
> +static void hisi_nfc_dma_transfer(struct hinfc_host *host, int todev)
> +{
> +	struct mtd_info	*mtd = &host->mtd;
> +	struct nand_chip *chip = mtd->priv;
> +	unsigned long val;
> +	int ret;
> +
> +	hinfc_write(host, host->dma_buffer, HINFC504_DMA_ADDR_DATA);
> +	hinfc_write(host, host->dma_oob, HINFC504_DMA_ADDR_OOB);
> +
> +	if (chip->ecc.mode == NAND_ECC_NONE) {
> +		hinfc_write(host, ((mtd->oobsize & HINFC504_DMA_LEN_OOB_MASK)
> +			<< HINFC504_DMA_LEN_OOB_SHIFT), HINFC504_DMA_LEN);
> +
> +		hinfc_write(host, HINFC504_DMA_PARA_DATA_RW_EN
> +			| HINFC504_DMA_PARA_OOB_RW_EN, HINFC504_DMA_PARA);
> +	} else {
> +		if (host->command == NAND_CMD_READOOB)
> +			hinfc_write(host, HINFC504_DMA_PARA_OOB_RW_EN
> +			| HINFC504_DMA_PARA_OOB_EDC_EN
> +			| HINFC504_DMA_PARA_OOB_ECC_EN, HINFC504_DMA_PARA);
> +		else
> +			hinfc_write(host, HINFC504_DMA_PARA_DATA_RW_EN
> +			| HINFC504_DMA_PARA_OOB_RW_EN
> +			| HINFC504_DMA_PARA_DATA_EDC_EN
> +			| HINFC504_DMA_PARA_OOB_EDC_EN
> +			| HINFC504_DMA_PARA_DATA_ECC_EN
> +			| HINFC504_DMA_PARA_OOB_ECC_EN, HINFC504_DMA_PARA);
> +
> +	}
> +
> +	val = (HINFC504_DMA_CTRL_DMA_START | HINFC504_DMA_CTRL_BURST4_EN
> +		| HINFC504_DMA_CTRL_BURST8_EN | HINFC504_DMA_CTRL_BURST16_EN
> +		| HINFC504_DMA_CTRL_DATA_AREA_EN | HINFC504_DMA_CTRL_OOB_AREA_EN
> +		| ((host->addr_cycle == 4 ? 1 : 0)
> +			<< HINFC504_DMA_CTRL_ADDR_NUM_SHIFT)
> +		| ((host->chipselect & HINFC504_DMA_CTRL_CS_MASK)
> +			<< HINFC504_DMA_CTRL_CS_SHIFT));
> +
> +	if (todev)
> +		val |= HINFC504_DMA_CTRL_WE;
> +
> +	init_completion(&host->cmd_complete);
> +
> +	hinfc_write(host, val, HINFC504_DMA_CTRL);
> +	ret = wait_for_completion_timeout(&host->cmd_complete,
> +			HINFC504_NFC_DMA_TIMEOUT);
> +
> +	if (!ret) {
> +		dev_err(host->dev, "DMA operation(irq) timeout!\n");
> +		/* sanity check */
> +		val = hinfc_read(host, HINFC504_DMA_CTRL);
> +		if (!(val & HINFC504_DMA_CTRL_DMA_START))
> +			dev_err(host->dev, "DMA is already done but without irq ACK!\n");
> +		else
> +			dev_err(host->dev, "DMA is really timeout!\n");
> +	}
> +}
> +
> +static int hisi_nfc_send_cmd_pageprog(struct hinfc_host *host)
> +{
> +	host->addr_value[0] &= 0xffff0000;
> +
> +	hinfc_write(host, host->addr_value[0], HINFC504_ADDRL);
> +	hinfc_write(host, host->addr_value[1], HINFC504_ADDRH);
> +	hinfc_write(host, NAND_CMD_PAGEPROG << 8 | NAND_CMD_SEQIN,
> +		    HINFC504_CMD);
> +
> +	hisi_nfc_dma_transfer(host, 1);
> +
> +	return 0;
> +}
> +
> +static int hisi_nfc_send_cmd_readstart(struct hinfc_host *host)
> +{
> +	struct mtd_info	*mtd = &host->mtd;
> +
> +	if ((host->addr_value[0] == host->cache_addr_value[0]) &&
> +	    (host->addr_value[1] == host->cache_addr_value[1]))
> +		return 0;
> +
> +	host->addr_value[0] &= 0xffff0000;
> +
> +	hinfc_write(host, host->addr_value[0], HINFC504_ADDRL);
> +	hinfc_write(host, host->addr_value[1], HINFC504_ADDRH);
> +	hinfc_write(host, NAND_CMD_READSTART << 8 | NAND_CMD_READ0,
> +		    HINFC504_CMD);
> +
> +	hinfc_write(host, 0, HINFC504_LOG_READ_ADDR);
> +	hinfc_write(host, mtd->writesize + mtd->oobsize,
> +		    HINFC504_LOG_READ_LEN);
> +
> +	hisi_nfc_dma_transfer(host, 0);
> +
> +	host->cache_addr_value[0] = host->addr_value[0];
> +	host->cache_addr_value[1] = host->addr_value[1];
> +
> +	return 0;
> +}
> +
> +static int hisi_nfc_send_cmd_erase(struct hinfc_host *host)
> +{
> +	hinfc_write(host, host->addr_value[0], HINFC504_ADDRL);
> +	hinfc_write(host, (NAND_CMD_ERASE2 << 8) | NAND_CMD_ERASE1,
> +		    HINFC504_CMD);
> +
> +	hinfc_write(host, HINFC504_OP_WAIT_READY_EN
> +		| HINFC504_OP_CMD2_EN
> +		| HINFC504_OP_CMD1_EN
> +		| HINFC504_OP_ADDR_EN
> +		| ((host->chipselect & HINFC504_OP_NF_CS_MASK)
> +			<< HINFC504_OP_NF_CS_SHIFT)
> +		| ((host->addr_cycle & HINFC504_OP_ADDR_CYCLE_MASK)
> +			<< HINFC504_OP_ADDR_CYCLE_SHIFT),
> +		HINFC504_OP);
> +
> +	wait_controller_finished(host);
> +
> +	return 0;
> +}
> +
> +static int hisi_nfc_send_cmd_readid(struct hinfc_host *host)
> +{
> +	hinfc_write(host, HINFC504_NANDINFO_LEN, HINFC504_DATA_NUM);
> +	hinfc_write(host, NAND_CMD_READID, HINFC504_CMD);
> +	hinfc_write(host, 0, HINFC504_ADDRL);
> +
> +	hinfc_write(host, HINFC504_OP_CMD1_EN | HINFC504_OP_ADDR_EN
> +		| HINFC504_OP_READ_DATA_EN
> +		| ((host->chipselect & HINFC504_OP_NF_CS_MASK)
> +			<< HINFC504_OP_NF_CS_SHIFT)
> +		| 1 << HINFC504_OP_ADDR_CYCLE_SHIFT, HINFC504_OP);
> +
> +	wait_controller_finished(host);
> +
> +	return 0;
> +}
> +
> +static int hisi_nfc_send_cmd_status(struct hinfc_host *host)
> +{
> +	hinfc_write(host, HINFC504_NANDINFO_LEN, HINFC504_DATA_NUM);
> +	hinfc_write(host, NAND_CMD_STATUS, HINFC504_CMD);
> +	hinfc_write(host, HINFC504_OP_CMD1_EN
> +		| HINFC504_OP_READ_DATA_EN
> +		| ((host->chipselect & HINFC504_OP_NF_CS_MASK)
> +			<< HINFC504_OP_NF_CS_SHIFT),
> +		HINFC504_OP);
> +
> +	wait_controller_finished(host);
> +
> +	return 0;
> +}
> +
> +static int hisi_nfc_send_cmd_reset(struct hinfc_host *host, int chipselect)
> +{
> +	hinfc_write(host, NAND_CMD_RESET, HINFC504_CMD);
> +
> +	hinfc_write(host, HINFC504_OP_CMD1_EN
> +		| ((chipselect & HINFC504_OP_NF_CS_MASK)
> +			<< HINFC504_OP_NF_CS_SHIFT)
> +		| HINFC504_OP_WAIT_READY_EN,
> +		HINFC504_OP);
> +
> +	wait_controller_finished(host);
> +
> +	return 0;
> +}
> +
> +static void hisi_nfc_select_chip(struct mtd_info *mtd, int chipselect)
> +{
> +	struct nand_chip *chip = mtd->priv;
> +	struct hinfc_host *host = chip->priv;
> +
> +	if (chipselect < 0)
> +		return;
> +
> +	host->chipselect = chipselect;
> +}
> +
> +static uint8_t hisi_nfc_read_byte(struct mtd_info *mtd)
> +{
> +	struct nand_chip *chip = mtd->priv;
> +	struct hinfc_host *host = chip->priv;
> +
> +	if (host->command == NAND_CMD_STATUS)
> +		return readb(chip->IO_ADDR_R);
> +
> +	host->offset++;
> +
> +	if (host->command == NAND_CMD_READID)
> +		return readb(chip->IO_ADDR_R + host->offset - 1);
> +
> +	return readb(host->buffer + host->offset - 1);

You're reading from memory, not IO. You don't need readb().

> +}
> +
> +static u16 hisi_nfc_read_word(struct mtd_info *mtd)
> +{
> +	struct nand_chip *chip = mtd->priv;
> +	struct hinfc_host *host = chip->priv;
> +
> +	host->offset += 2;
> +	return readw(host->buffer + host->offset - 2);

Same here, for readw().

> +}
> +
> +static void
> +hisi_nfc_write_buf(struct mtd_info *mtd, const uint8_t *buf, int len)
> +{
> +	struct nand_chip *chip = mtd->priv;
> +	struct hinfc_host *host = chip->priv;
> +
> +	memcpy(host->buffer + host->offset, buf, len);
> +	host->offset += len;
> +}
> +
> +static void hisi_nfc_read_buf(struct mtd_info *mtd, uint8_t *buf, int len)
> +{
> +	struct nand_chip *chip = mtd->priv;
> +	struct hinfc_host *host = chip->priv;
> +
> +	memcpy(buf, host->buffer + host->offset, len);
> +	host->offset += len;
> +}
> +
> +static void set_addr(struct mtd_info *mtd, int column, int page_addr)
> +{
> +	struct nand_chip *chip = mtd->priv;
> +	struct hinfc_host *host = chip->priv;
> +	unsigned int command = host->command;
> +
> +	host->addr_cycle    = 0;
> +	host->addr_value[0] = 0;
> +	host->addr_value[1] = 0;
> +
> +	/* Serially input address */
> +	if (column != -1) {
> +		/* Adjust columns for 16 bit buswidth */
> +		if (chip->options & NAND_BUSWIDTH_16 &&
> +				!nand_opcode_8bits(command))
> +			column >>= 1;
> +
> +		host->addr_value[0] = column & 0xffff;
> +		host->addr_cycle    = 2;
> +	}
> +	if (page_addr != -1) {
> +		host->addr_value[0] |= (page_addr & 0xffff)
> +			<< (host->addr_cycle * 8);
> +		host->addr_cycle    += 2;
> +		/* One more address cycle for devices > 128MiB */
> +		if (chip->chipsize > (128 << 20)) {
> +			host->addr_cycle += 1;
> +			if (host->command == NAND_CMD_ERASE1)
> +				host->addr_value[0] |= ((page_addr >> 16) & 0xff) << 16;
> +			else
> +				host->addr_value[1] |= ((page_addr >> 16) & 0xff);
> +		}
> +	}
> +}
> +
> +static void hisi_nfc_cmdfunc(struct mtd_info *mtd, unsigned command, int column,
> +		int page_addr)
> +{
> +	struct nand_chip *chip = mtd->priv;
> +	struct hinfc_host *host = chip->priv;
> +	int is_cache_invalid = 1;
> +	unsigned int flag = 0;
> +
> +	host->command =  command;
> +
> +	switch (command) {
> +	case NAND_CMD_READ0:
> +	case NAND_CMD_READOOB:
> +		if (command == NAND_CMD_READ0)
> +			host->offset = column;
> +		else
> +			host->offset = column + mtd->writesize;
> +
> +		is_cache_invalid = 0;
> +		set_addr(mtd, column, page_addr);
> +		hisi_nfc_send_cmd_readstart(host);
> +		break;
> +
> +	case NAND_CMD_SEQIN:
> +		host->offset = column;
> +		set_addr(mtd, column, page_addr);
> +		break;
> +
> +	case NAND_CMD_ERASE1:
> +		set_addr(mtd, column, page_addr);
> +		break;
> +
> +	case NAND_CMD_PAGEPROG:
> +		hisi_nfc_send_cmd_pageprog(host);
> +		break;
> +
> +	case NAND_CMD_ERASE2:
> +		hisi_nfc_send_cmd_erase(host);
> +		break;
> +
> +	case NAND_CMD_READID:
> +		host->offset = column;
> +		memset(chip->IO_ADDR_R, 0, 0x10);
> +		hisi_nfc_send_cmd_readid(host);
> +		break;
> +
> +	case NAND_CMD_STATUS:
> +		flag = hinfc_read(host, HINFC504_CON);
> +		if (chip->ecc.mode == NAND_ECC_HW)
> +			hinfc_write(host,
> +				    flag && ~(HINFC504_CON_ECCTYPE_MASK <<
> +				    HINFC504_CON_ECCTYPE_SHIFT), HINFC504_CON);
> +
> +		host->offset = 0;
> +		memset(chip->IO_ADDR_R, 0, 0x10);
> +		hisi_nfc_send_cmd_status(host);
> +		hinfc_write(host, flag, HINFC504_CON);
> +		break;
> +
> +	case NAND_CMD_RESET:
> +		hisi_nfc_send_cmd_reset(host, host->chipselect);
> +		break;
> +
> +	default:
> +		dev_err(host->dev, "Error: unsupported cmd(cmd=%x, col=%x, page=%x)\n",
> +			command, column, page_addr);
> +	}
> +
> +	if (is_cache_invalid) {
> +		host->cache_addr_value[0] = ~0;
> +		host->cache_addr_value[1] = ~0;
> +	}
> +}
> +
> +static irqreturn_t hinfc_irq_handle(int irq, void *devid)
> +{
> +	struct hinfc_host *host = devid;
> +	unsigned int flag;
> +
> +	flag = hinfc_read(host, HINFC504_INTS);
> +	/* store interrupts state */
> +	host->irq_status |= flag;
> +
> +	if (flag & HINFC504_INTS_DMA) {
> +		hinfc_write(host, HINFC504_INTCLR_DMA, HINFC504_INTCLR);
> +		complete(&host->cmd_complete);
> +	} else if (flag & HINFC504_INTS_CE) {
> +		hinfc_write(host, HINFC504_INTCLR_CE, HINFC504_INTCLR);
> +	} else if (flag & HINFC504_INTS_UE) {
> +		hinfc_write(host, HINFC504_INTCLR_UE, HINFC504_INTCLR);
> +	}
> +
> +	return IRQ_HANDLED;
> +}
> +
> +static int hisi_nand_read_page_hwecc(struct mtd_info *mtd,
> +	struct nand_chip *chip, uint8_t *buf, int oob_required, int page)
> +{
> +	struct hinfc_host *host = chip->priv;
> +	int max_bitflips = 0, stat = 0, stat_max, status_ecc;
> +	int stat_1, stat_2;
> +
> +	chip->read_buf(mtd, buf, mtd->writesize);
> +	chip->read_buf(mtd, chip->oob_poi, mtd->oobsize);
> +
> +	/* errors which can not be corrected by ECC */
> +	if (host->irq_status & HINFC504_INTS_UE) {
> +		mtd->ecc_stats.failed++;
> +	} else if (host->irq_status & HINFC504_INTS_CE) {
> +		/* TODO: need add other ECC modes! */
> +		switch (chip->ecc.strength) {
> +		case 1:
> +			stat = hweight8(hinfc_read(host, HINFC504_ECC_STATUS)>>
> +						HINFC504_ECC_1_BIT_SHIFT);
> +			stat_max = 1;
> +			break;
> +		case 16:
> +			status_ecc = hinfc_read(host, HINFC504_ECC_STATUS) >>
> +					HINFC504_ECC_16_BIT_SHIFT & 0x0fff;
> +			stat_2 = status_ecc & 0x3f;
> +			stat_1 = status_ecc >> 6 & 0x3f;
> +			stat = stat_1 + stat_2;
> +			stat_max = max_t(int, stat_1, stat_2);
> +		}
> +		mtd->ecc_stats.corrected += stat;
> +		max_bitflips = max_t(int, max_bitflips, stat_max);
> +	}
> +	host->irq_status = 0;
> +
> +	return max_bitflips;
> +}
> +
> +static int hisi_nand_read_oob(struct mtd_info *mtd, struct nand_chip *chip,
> +				int page)
> +{
> +	struct hinfc_host *host = chip->priv;
> +
> +	chip->cmdfunc(mtd, NAND_CMD_READOOB, 0, page);
> +	chip->read_buf(mtd, chip->oob_poi, mtd->oobsize);
> +
> +	if (host->irq_status & HINFC504_INTS_UE) {
> +		host->irq_status = 0;
> +		return -EBADMSG;
> +	}
> +
> +	host->irq_status = 0;
> +	return 0;
> +}
> +
> +static int hisi_nand_write_page_hwecc(struct mtd_info *mtd,
> +		struct nand_chip *chip, const uint8_t *buf, int oob_required)
> +{
> +	chip->write_buf(mtd, buf, mtd->writesize);
> +	if (oob_required)
> +		chip->write_buf(mtd, chip->oob_poi, mtd->oobsize);
> +
> +	return 0;
> +}
> +
> +static void hisi_nfc_host_init(struct hinfc_host *host)
> +{
> +	struct nand_chip *chip = &host->chip;
> +	unsigned int flag = 0;
> +
> +	host->version = hinfc_read(host, HINFC_VERSION);
> +	host->addr_cycle		= 0;
> +	host->addr_value[0]		= 0;
> +	host->addr_value[1]		= 0;
> +	host->cache_addr_value[0]	= ~0;
> +	host->cache_addr_value[1]	= ~0;
> +	host->chipselect		= 0;
> +
> +	/* default page size: 2K, ecc_none. need modify */
> +	flag = HINFC504_CON_OP_MODE_NORMAL | HINFC504_CON_READY_BUSY_SEL
> +		| ((0x001 & HINFC504_CON_PAGESIZE_MASK)
> +			<< HINFC504_CON_PAGEISZE_SHIFT)
> +		| ((0x0 & HINFC504_CON_ECCTYPE_MASK)
> +			<< HINFC504_CON_ECCTYPE_SHIFT)
> +		| ((chip->options & NAND_BUSWIDTH_16) ?
> +			HINFC504_CON_BUS_WIDTH : 0);
> +	hinfc_write(host, flag, HINFC504_CON);
> +
> +	memset(chip->IO_ADDR_R, 0xff, HINFC504_BUFFER_BASE_ADDRESS_LEN);
> +
> +	hinfc_write(host, SET_HINFC504_PWIDTH(HINFC504_W_LATCH,
> +		    HINFC504_R_LATCH, HINFC504_RW_LATCH), HINFC504_PWIDTH);
> +
> +	/* enable DMA irq */
> +	hinfc_write(host, HINFC504_INTEN_DMA, HINFC504_INTEN);
> +}
> +
> +static struct nand_ecclayout nand_ecc_2K_1bit = {
> +	.oobfree = { {24, 40} }
> +};
> +
> +static struct nand_ecclayout nand_ecc_2K_16bits = {
> +	.oobavail = 6,
> +	.oobfree = { {2, 6} },
> +};
> +
> +static int hisi_nfc_ecc_probe(struct hinfc_host *host)
> +{
> +	unsigned int flag;
> +	int size, strength, ecc_bits;
> +	struct device *dev = host->dev;
> +	struct nand_chip *chip = &host->chip;
> +	struct mtd_info *mtd = &host->mtd;
> +	struct device_node *np = host->dev->of_node;
> +
> +	size = of_get_nand_ecc_step_size(np);
> +	strength = of_get_nand_ecc_strength(np);
> +	if ((size != 512) && (size != 1024)) {
> +		dev_err(dev, "error ecc size: %d\n", size);
> +		return -EINVAL;
> +	}
> +
> +	if ((size == 512) && (strength != 1)) {
> +		dev_err(dev, "ecc size and strength do not match\n");
> +		return -EINVAL;
> +	}
> +	if ((size == 1024) && ((strength != 8) && (strength != 16) &&
> +				(strength != 24) && (strength != 40))) {
> +		dev_err(dev, "ecc size and strength do not match\n");
> +		return -EINVAL;
> +	}
> +
> +	chip->ecc.size = size;
> +	chip->ecc.strength = strength;
> +
> +	chip->ecc.read_page = hisi_nand_read_page_hwecc;
> +	chip->ecc.read_oob = hisi_nand_read_oob;
> +	chip->ecc.write_page = hisi_nand_write_page_hwecc;
> +
> +	switch (chip->ecc.strength) {
> +	case 1:
> +		ecc_bits = 1;
> +		if (mtd->writesize == 2048)
> +			chip->ecc.layout = &nand_ecc_2K_1bit;
> +
> +		/* TODO: add more page size support */
> +		break;
> +	case 16:
> +		ecc_bits = 6;
> +		if (mtd->writesize == 2048)
> +			chip->ecc.layout = &nand_ecc_2K_16bits;
> +
> +		/* TODO: add more page size support */
> +		break;
> +
> +	/* TODO: add more ecc strength support */
> +	default:
> +		dev_err(dev, "not support strength: %d\n", chip->ecc.strength);
> +		return -EINVAL;
> +	}
> +
> +	flag = hinfc_read(host, HINFC504_CON);
> +	/* add ecc type configure */
> +	flag |= ((ecc_bits & HINFC504_CON_ECCTYPE_MASK)
> +						<< HINFC504_CON_ECCTYPE_SHIFT);
> +	hinfc_write(host, flag, HINFC504_CON);
> +
> +	/* enable ecc irq */
> +	flag = hinfc_read(host, HINFC504_INTEN) & 0xfff;
> +	hinfc_write(host, flag | HINFC504_INTEN_UE | HINFC504_INTEN_CE,
> +		    HINFC504_INTEN);
> +
> +	return 0;
> +}
> +
> +static int hisi_nfc_probe(struct platform_device *pdev)
> +{
> +	int ret = 0, irq, buswidth, flag, max_chips = HINFC504_MAX_CHIP;
> +	struct device *dev = &pdev->dev;
> +	struct hinfc_host *host;
> +	struct nand_chip  *chip;
> +	struct mtd_info   *mtd;
> +	struct resource	  *res;
> +	struct device_node *np = dev->of_node;
> +	struct mtd_part_parser_data ppdata;
> +
> +	host = devm_kzalloc(dev, sizeof(*host), GFP_KERNEL);
> +	if (!host)
> +		return -ENOMEM;
> +	host->dev = dev;
> +
> +	platform_set_drvdata(pdev, host);
> +	chip = &host->chip;
> +	mtd  = &host->mtd;
> +
> +	irq = platform_get_irq(pdev, 0);
> +	if (irq < 0) {
> +		dev_err(dev, "no IRQ resource defined\n");
> +		ret = -ENXIO;
> +		goto err_res;
> +	}
> +
> +	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
> +	host->iobase = devm_ioremap_resource(dev, res);
> +	if (IS_ERR(host->iobase)) {
> +		ret = PTR_ERR(host->iobase);
> +		dev_err(dev, "devm_ioremap_resource[0] fail\n");

I don't think yhou really need this error print. devm_ioremap_resource()
should be descriptive enough, I think.

> +		goto err_res;
> +	}
> +
> +	res = platform_get_resource(pdev, IORESOURCE_MEM, 1);
> +	chip->IO_ADDR_R = chip->IO_ADDR_W = devm_ioremap_resource(dev, res);

Hmm, do you really have to reuse IO_ADDR_{R,W} here? Those are only
targeted for NAND systems which have a direct MMIO mapping to the NAND
I/O pins. See nand_base's {read,write}_buf() and read_{byte,word}()
implementations. But you override those.

It's best if it's obvious if nand_base is somehow inadvertently using
these pointers. So leaving them NULL is helpful.

As an alternative, you can just stash another private void __iomem
pointer in you your host struct.

> +	if (IS_ERR(chip->IO_ADDR_R)) {
> +		ret = PTR_ERR(chip->IO_ADDR_R);
> +		dev_err(dev, "devm_ioremap_resource[1] fail\n");
> +		goto err_res;
> +	}
> +
> +	mtd->priv		= chip;
> +	mtd->owner		= THIS_MODULE;
> +	mtd->name		= "hisi_nand";
> +	mtd->dev.parent         = &pdev->dev;
> +
> +	chip->priv		= host;
> +	chip->cmdfunc		= hisi_nfc_cmdfunc;
> +	chip->select_chip	= hisi_nfc_select_chip;
> +	chip->read_byte		= hisi_nfc_read_byte;
> +	chip->read_word		= hisi_nfc_read_word;
> +	chip->write_buf		= hisi_nfc_write_buf;
> +	chip->read_buf		= hisi_nfc_read_buf;
> +	chip->chip_delay	= HINFC504_CHIP_DELAY;
> +
> +	chip->ecc.mode = of_get_nand_ecc_mode(np);
> +
> +	buswidth = of_get_nand_bus_width(np);
> +	if (buswidth == 16)
> +		chip->options |= NAND_BUSWIDTH_16;
> +
> +	hisi_nfc_host_init(host);
> +
> +	ret = devm_request_irq(dev, irq, hinfc_irq_handle, IRQF_DISABLED,
> +				"nandc", host);
> +	if (ret) {
> +		dev_err(dev, "failed to request IRQ\n");
> +		goto err_res;
> +	}
> +
> +	ret = nand_scan_ident(mtd, max_chips, NULL);
> +	if (ret) {
> +		ret = -ENODEV;
> +		goto err_res;
> +	}
> +
> +	host->buffer = dmam_alloc_coherent(dev, mtd->writesize + mtd->oobsize,
> +		&host->dma_buffer, GFP_KERNEL);

You need to check this for allocation failures.

> +	host->dma_oob = host->dma_buffer + mtd->writesize;
> +	memset(host->buffer, 0xff, mtd->writesize + mtd->oobsize);
> +
> +	flag = hinfc_read(host, HINFC504_CON);
> +	flag &= ~(HINFC504_CON_PAGESIZE_MASK << HINFC504_CON_PAGEISZE_SHIFT);
> +	switch (mtd->writesize) {
> +	case 2048:
> +		flag |= (0x001 << HINFC504_CON_PAGEISZE_SHIFT); break;
> +	/*
> +	 * TODO: add more pagesize support,
> +	 * default pagesize has been set in hisi_nfc_host_init
> +	 */
> +	default:
> +		dev_err(dev, "NON-2KB page size nand flash\n");
> +		ret = -EINVAL;
> +		goto err_res;
> +	}
> +	hinfc_write(host, flag, HINFC504_CON);
> +
> +	if (chip->ecc.mode == NAND_ECC_HW)
> +		hisi_nfc_ecc_probe(host);
> +
> +	ret = nand_scan_tail(mtd);
> +	if (ret) {
> +		dev_err(dev, "nand_scan_tail failed: %d\n", ret);
> +		goto err_res;
> +	}
> +
> +	ppdata.of_node = np;
> +	ret = mtd_device_parse_register(mtd, NULL, &ppdata, NULL, 0);
> +	if (ret) {
> +		dev_err(dev, "Err MTD partition=%d\n", ret);
> +		goto err_mtd;
> +	}
> +
> +	return 0;
> +
> +err_mtd:
> +	nand_release(mtd);
> +err_res:
> +	return ret;
> +}
> +
> +static int hisi_nfc_remove(struct platform_device *pdev)
> +{
> +	struct hinfc_host *host = platform_get_drvdata(pdev);
> +	struct mtd_info *mtd = &host->mtd;
> +
> +	nand_release(mtd);
> +
> +	return 0;
> +}
> +
> +#ifdef CONFIG_PM_SLEEP
> +static int hisi_nfc_suspend(struct device *dev)
> +{
> +	struct hinfc_host *host = dev_get_drvdata(dev);
> +	unsigned long timeout = jiffies + HINFC504_NFC_PM_TIMEOUT;
> +
> +	while (time_before(jiffies, timeout)) {
> +		if (((hinfc_read(host, HINFC504_STATUS) & 0x1) == 0x0) &&
> +		    (hinfc_read(host, HINFC504_DMA_CTRL) &
> +		     HINFC504_DMA_CTRL_DMA_START)) {
> +			_cond_resched();

Why not just cond_resched()?

> +			return 0;
> +		}
> +	}
> +
> +	dev_err(host->dev, "nand controller suspend timeout.\n");
> +
> +	return -EAGAIN;
> +}
> +
> +static int hisi_nfc_resume(struct device *dev)
> +{
> +	int cs;
> +	struct hinfc_host *host = dev_get_drvdata(dev);
> +	struct nand_chip *chip = &host->chip;
> +
> +	for (cs = 0; cs < chip->numchips; cs++)
> +		hisi_nfc_send_cmd_reset(host, cs);
> +	hinfc_write(host, SET_HINFC504_PWIDTH(HINFC504_W_LATCH,
> +		    HINFC504_R_LATCH, HINFC504_RW_LATCH), HINFC504_PWIDTH);
> +
> +	return 0;
> +}
> +#endif
> +static SIMPLE_DEV_PM_OPS(hisi_nfc_pm_ops, hisi_nfc_suspend, hisi_nfc_resume);
> +
> +static const struct of_device_id nfc_id_table[] = {
> +	{ .compatible = "hisilicon,504-nfc" },
> +	{}
> +};
> +MODULE_DEVICE_TABLE(of, nfc_id_table);
> +
> +static struct platform_driver hisi_nfc_driver = {
> +	.driver = {
> +		.name  = "hisi_nand",
> +		.of_match_table = of_match_ptr(nfc_id_table),
> +		.pm = &hisi_nfc_pm_ops,
> +	},
> +	.probe		= hisi_nfc_probe,
> +	.remove		= hisi_nfc_remove,
> +};
> +
> +module_platform_driver(hisi_nfc_driver);
> +
> +MODULE_LICENSE("GPL");
> +MODULE_AUTHOR("Zhiyong Cai");
> +MODULE_AUTHOR("Zhou Wang");
> +MODULE_DESCRIPTION("Hisilicon Nand Flash Controller Driver");

Brian



More information about the linux-arm-kernel mailing list