[PATCH V5] ARM: dts: imx6q-icore-rqs: Add Engicam IMX6 Q7 initial support
Michael Trimarchi
michael at amarulasolutions.com
Thu Dec 24 01:24:47 PST 2015
www.engicam.com/en/products/embedded/som/standard/i-core-rqs-m6s-dl-d-q
Signed-off-by: Michael Trimarchi <michael at amarulasolutions.com>
---
Test on top of ARM: dts: imx6q: clean up unused ipu2grp
Changes in v5:
- None
Changes in v4:
- update regulator name
- using flat pins,fsl
- move iomuxc
- add X11 license
- better alphabetic order
Changes in v3:
- add sgtl audio support
- add ethernet gigabit tuning
- use hub reset only in usbhub and not
in otg vbus
Changes in v2:
- add the board in alphabetic order
- remove cpu operating point
- remove simple-bus and adjust regulaotor
- add gpios to correct pinctrl
- remove no mainline binding of gpc
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/imx6q-icore-rqs.dts | 78 ++++++
arch/arm/boot/dts/imx6qdl-icore-rqs.dtsi | 410 +++++++++++++++++++++++++++++++
3 files changed, 489 insertions(+)
create mode 100644 arch/arm/boot/dts/imx6q-icore-rqs.dts
create mode 100644 arch/arm/boot/dts/imx6qdl-icore-rqs.dtsi
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index bb8fa02..7e8f29c 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -312,6 +312,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
imx6q-gw551x.dtb \
imx6q-gw552x.dtb \
imx6q-hummingboard.dtb \
+ imx6q-icore-rqs.dtb \
imx6q-nitrogen6x.dtb \
imx6q-phytec-pbab01.dtb \
imx6q-rex-pro.dtb \
diff --git a/arch/arm/boot/dts/imx6q-icore-rqs.dts b/arch/arm/boot/dts/imx6q-icore-rqs.dts
new file mode 100644
index 0000000..0053188
--- /dev/null
+++ b/arch/arm/boot/dts/imx6q-icore-rqs.dts
@@ -0,0 +1,78 @@
+/*
+ * Copyright (C) 2015 Amarula Solutions B.V.
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * version 2 as published by the Free Software Foundation.
+ *
+ * This file is distributed in the hope that it will be useful
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+
+#include "imx6q.dtsi"
+#include "imx6qdl-icore-rqs.dtsi"
+
+/ {
+ model = "Engicam i.CoreM6 Quad SOM";
+ compatible = "engicam,imx6-icore-rqs", "fsl,imx6q";
+
+ sound {
+ compatible = "fsl,imx-audio-sgtl5000";
+ model = "imx-audio-sgtl5000";
+ ssi-controller = <&ssi1>;
+ audio-codec = <&codec>;
+ audio-routing =
+ "MIC_IN", "Mic Jack",
+ "Mic Jack", "Mic Bias",
+ "Headphone Jack", "HP_OUT";
+ mux-int-port = <1>;
+ mux-ext-port = <4>;
+ };
+};
+
+&i2c3 {
+ codec: sgtl5000 at 0a {
+ compatible = "fsl,sgtl5000";
+ reg = <0x0a>;
+ clocks = <&clks IMX6QDL_CLK_CKO>;
+ VDDA-supply = <®_2p5v>;
+ VDDIO-supply = <®_3p3v>;
+ VDDD-supply = <®_1p8v>;
+ };
+};
+
+&sata {
+ status = "okay";
+};
diff --git a/arch/arm/boot/dts/imx6qdl-icore-rqs.dtsi b/arch/arm/boot/dts/imx6qdl-icore-rqs.dtsi
new file mode 100644
index 0000000..b984128
--- /dev/null
+++ b/arch/arm/boot/dts/imx6qdl-icore-rqs.dtsi
@@ -0,0 +1,410 @@
+/*
+ * Copyright (C) 2015 Amarula Solutions B.V.
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * version 2 as published by the Free Software Foundation.
+ *
+ * This file is distributed in the hope that it will be useful
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/clock/imx6qdl-clock.h>
+
+/ {
+ memory {
+ reg = <0x10000000 0x80000000>;
+ };
+
+ reg_1p8v: regulator-1p8v {
+ compatible = "regulator-fixed";
+ regulator-name = "1P8V";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ reg_2p5v: regulator-2p5v {
+ compatible = "regulator-fixed";
+ regulator-name = "2P5V";
+ regulator-min-microvolt = <2500000>;
+ regulator-max-microvolt = <2500000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ reg_3p3v: regulator-3p3v {
+ compatible = "regulator-fixed";
+ regulator-name = "3P3V";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ reg_sd3_vmmc: sd3-vmmc {
+ compatible = "regulator-fixed";
+ regulator-name = "P3V3_SD3_SWITCHED";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ gpio = <&gpio1 4 GPIO_ACTIVE_LOW>;
+ enable-active-high;
+ };
+
+ reg_sd4_vmmc: sd4-vmmc {
+ compatible = "regulator-fixed";
+ regulator-name = "P3V3_SD4_SWITCHED";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ reg_usb_h1_vbus: usb-h1-vbus {
+ compatible = "regulator-fixed";
+ regulator-name = "usb_h1_vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ reg_usb_otg_vbus: usb-otg-vbus {
+ compatible = "regulator-fixed";
+ regulator-name = "usb_otg_vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ usb_hub: usb-hub {
+ compatible = "smsc,usb3503a";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usbhub>;
+ reset-gpios = <&gpio1 6 GPIO_ACTIVE_LOW>;
+ clocks = <&clks IMX6QDL_CLK_LVDS2_GATE>;
+ clock-names = "refclk";
+ };
+};
+
+&clks {
+ assigned-clocks = <&clks IMX6QDL_CLK_LVDS2_SEL>;
+ assigned-clock-parents = <&clks IMX6QDL_CLK_OSC>;
+};
+
+&audmux {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_audmux>;
+ status = "okay";
+};
+
+&fec {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_enet_3>;
+ phy-handle = <ð_phy>;
+ phy-mode = "rgmii";
+ status = "okay";
+ mdio {
+ eth_phy: ethernet-phy {
+ rxc-skew-ps = <1140>;
+ txc-skew-ps = <1140>;
+ txen-skew-ps = <600>;
+ rxdv-skew-ps = <240>;
+ rxd0-skew-ps = <420>;
+ rxd1-skew-ps = <600>;
+ rxd2-skew-ps = <420>;
+ rxd3-skew-ps = <240>;
+ txd0-skew-ps = <60>;
+ txd1-skew-ps = <60>;
+ txd2-skew-ps = <60>;
+ txd3-skew-ps = <240>;
+ };
+ };
+};
+
+&i2c1 {
+ clock-frequency = <100000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c1_1>;
+ status = "okay";
+};
+
+&i2c2 {
+ clock-frequency = <100000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c2_2>;
+ status = "okay";
+};
+
+&i2c3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c3_4>;
+ status = "okay";
+};
+
+&pcie {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pcie>;
+ reset-gpio = <&gpio3 29 GPIO_ACTIVE_LOW>;
+ status = "okay";
+};
+
+&ssi1 {
+ fsl,mode = "i2s-slave";
+ status = "okay";
+};
+
+&uart4 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart4_1>;
+ status = "okay";
+};
+
+&usbh1 {
+ vbus-supply = <®_usb_h1_vbus>;
+ disable-over-current;
+ clocks = <&clks IMX6QDL_CLK_USBOH3>;
+ status = "okay";
+};
+
+&usbotg {
+ vbus-supply = <®_usb_otg_vbus>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usbotg_2>;
+ disable-over-current;
+ status = "okay";
+};
+
+&usdhc1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usdhc1_1>;
+ no-1-8-v;
+ status = "okay";
+};
+
+&usdhc3 {
+ pinctrl-names = "default", "state_100mhz", "state_200mhz";
+ pinctrl-0 = <&pinctrl_usdhc3_2>;
+ pinctrl-1 = <&pinctrl_usdhc3_2_100mhz>;
+ pinctrl-2 = <&pinctrl_usdhc3_2_200mhz>;
+ vmcc-supply = <®_sd3_vmmc>;
+ cd-gpios = <&gpio1 1 GPIO_ACTIVE_LOW>;
+ bus-witdh=<4>;
+ no-1-8-v;
+ status = "okay";
+};
+
+&usdhc4 {
+ pinctrl-names = "default", "state_100mhz", "state_200mhz";
+ pinctrl-0 = <&pinctrl_usdhc4_1>;
+ pinctrl-1 = <&pinctrl_usdhc4_1_100mhz>;
+ pinctrl-2 = <&pinctrl_usdhc4_1_200mhz>;
+ vmcc-supply = <®_sd4_vmmc>;
+ bus-witdh=<8>;
+ no-1-8-v;
+ non-removable;
+ status = "okay";
+};
+
+&iomuxc {
+ pinctrl_audmux: audmux {
+ fsl,pins = <
+ MX6QDL_PAD_DISP0_DAT20__AUD4_TXC 0x130b0
+ MX6QDL_PAD_DISP0_DAT21__AUD4_TXD 0x110b0
+ MX6QDL_PAD_DISP0_DAT22__AUD4_TXFS 0x130b0
+ MX6QDL_PAD_DISP0_DAT23__AUD4_RXD 0x130b0
+ >;
+ };
+
+ pinctrl_enet_3: enetgrp-3 {
+ fsl,pins = <
+ MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x1b0b0
+ MX6QDL_PAD_ENET_MDC__ENET_MDC 0x1b0b0
+ MX6QDL_PAD_RGMII_TXC__RGMII_TXC 0x1b0b0
+ MX6QDL_PAD_RGMII_TD0__RGMII_TD0 0x1b0b0
+ MX6QDL_PAD_RGMII_TD1__RGMII_TD1 0x1b0b0
+ MX6QDL_PAD_RGMII_TD2__RGMII_TD2 0x1b0b0
+ MX6QDL_PAD_RGMII_TD3__RGMII_TD3 0x1b0b0
+ MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL 0x1b0b0
+ MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK 0x1b0b0
+ MX6QDL_PAD_RGMII_RXC__RGMII_RXC 0x1b0b0
+ MX6QDL_PAD_RGMII_RD0__RGMII_RD0 0x1b0b0
+ MX6QDL_PAD_RGMII_RD1__RGMII_RD1 0x1b0b0
+ MX6QDL_PAD_RGMII_RD2__RGMII_RD2 0x1b0b0
+ MX6QDL_PAD_RGMII_RD3__RGMII_RD3 0x1b0b0
+ MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL 0x1b0b0
+ MX6QDL_PAD_ENET_TX_EN__ENET_TX_EN 0x1b0b0
+ >;
+ };
+
+ pinctrl_i2c1_1: i2c1grp-1 {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_D21__I2C1_SCL 0x4001b8b1
+ MX6QDL_PAD_EIM_D28__I2C1_SDA 0x4001b8b1
+ >;
+ };
+
+ pinctrl_i2c2_2: i2c2grp-2 {
+ fsl,pins = <
+ MX6QDL_PAD_KEY_COL3__I2C2_SCL 0x4001b8b1
+ MX6QDL_PAD_KEY_ROW3__I2C2_SDA 0x4001b8b1
+ >;
+ };
+
+ pinctrl_i2c3_4: i2c3grp-4 {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_5__I2C3_SCL 0x4001b8b1
+ MX6QDL_PAD_EIM_D18__I2C3_SDA 0x4001b8b1
+ MX6QDL_PAD_GPIO_0__CCM_CLKO1 0x130b0
+ >;
+ };
+
+ pinctrl_pcie: pciegrp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_D29__GPIO3_IO29 0x1f059 /* PCIe Reset */
+ >;
+ };
+
+ pinctrl_uart4_1: uart4grp-1 {
+ fsl,pins = <
+ MX6QDL_PAD_KEY_COL0__UART4_TX_DATA 0x1b0b1
+ MX6QDL_PAD_KEY_ROW0__UART4_RX_DATA 0x1b0b1
+ >;
+ };
+
+ pinctrl_usbhub: usbhubgrp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_6__GPIO1_IO06 0x1f059 /* HUB USB Reset */
+ >;
+ };
+
+ pinctrl_usbotg_2: usbotggrp-2 {
+ fsl,pins = <
+ MX6QDL_PAD_ENET_RX_ER__USB_OTG_ID 0x17059
+ >;
+ };
+
+ pinctrl_usdhc1_1: usdhc1grp-1 {
+ fsl,pins = <
+ MX6QDL_PAD_SD1_CMD__SD1_CMD 0x17071
+ MX6QDL_PAD_SD1_CLK__SD1_CLK 0x10071
+ MX6QDL_PAD_SD1_DAT0__SD1_DATA0 0x17071
+ MX6QDL_PAD_SD1_DAT1__SD1_DATA1 0x17071
+ MX6QDL_PAD_SD1_DAT2__SD1_DATA2 0x17071
+ MX6QDL_PAD_SD1_DAT3__SD1_DATA3 0x17071
+ >;
+ };
+
+ pinctrl_usdhc3_2: usdhc3grp-2 {
+ fsl,pins = <
+ MX6QDL_PAD_SD3_CMD__SD3_CMD 0x17070
+ MX6QDL_PAD_SD3_CLK__SD3_CLK 0x10070
+ MX6QDL_PAD_SD3_DAT0__SD3_DATA0 0x17070
+ MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x17070
+ MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x17070
+ MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x17070
+ MX6QDL_PAD_GPIO_1__GPIO1_IO01 0x1f059 /* CD */
+ MX6QDL_PAD_GPIO_4__GPIO1_IO04 0x1f059 /* PWR */
+ >;
+ };
+
+ pinctrl_usdhc3_2_100mhz: usdhc3grp-2_100mhz {
+ fsl,pins = <
+ MX6QDL_PAD_SD3_CMD__SD3_CMD 0x170B1
+ MX6QDL_PAD_SD3_CLK__SD3_CLK 0x100B1
+ MX6QDL_PAD_SD3_DAT0__SD3_DATA0 0x170B1
+ MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x170B1
+ MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x170B1
+ MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x170B1
+ >;
+ };
+
+ pinctrl_usdhc3_2_200mhz: usdhc3grp-2_200mhz {
+ fsl,pins = <
+ MX6QDL_PAD_SD3_CMD__SD3_CMD 0x170F9
+ MX6QDL_PAD_SD3_CLK__SD3_CLK 0x100F9
+ MX6QDL_PAD_SD3_DAT0__SD3_DATA0 0x170F9
+ MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x170F9
+ MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x170F9
+ MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x170F9
+ >;
+ };
+
+ pinctrl_usdhc4_1: usdhc4grp-1 {
+ fsl,pins = <
+ MX6QDL_PAD_SD4_CMD__SD4_CMD 0x17070
+ MX6QDL_PAD_SD4_CLK__SD4_CLK 0x10070
+ MX6QDL_PAD_SD4_DAT0__SD4_DATA0 0x17070
+ MX6QDL_PAD_SD4_DAT1__SD4_DATA1 0x17070
+ MX6QDL_PAD_SD4_DAT2__SD4_DATA2 0x17070
+ MX6QDL_PAD_SD4_DAT3__SD4_DATA3 0x17070
+ MX6QDL_PAD_SD4_DAT4__SD4_DATA4 0x17070
+ MX6QDL_PAD_SD4_DAT5__SD4_DATA5 0x17070
+ MX6QDL_PAD_SD4_DAT6__SD4_DATA6 0x17070
+ MX6QDL_PAD_SD4_DAT7__SD4_DATA7 0x17070
+ >;
+ };
+
+ pinctrl_usdhc4_1_100mhz: usdhc4grp-1_100mhz {
+ fsl,pins = <
+ MX6QDL_PAD_SD4_CMD__SD4_CMD 0x170B1
+ MX6QDL_PAD_SD4_CLK__SD4_CLK 0x100B1
+ MX6QDL_PAD_SD4_DAT0__SD4_DATA0 0x170B1
+ MX6QDL_PAD_SD4_DAT1__SD4_DATA1 0x170B1
+ MX6QDL_PAD_SD4_DAT2__SD4_DATA2 0x170B1
+ MX6QDL_PAD_SD4_DAT3__SD4_DATA3 0x170B1
+ MX6QDL_PAD_SD4_DAT4__SD4_DATA4 0x170B1
+ MX6QDL_PAD_SD4_DAT5__SD4_DATA5 0x170B1
+ MX6QDL_PAD_SD4_DAT6__SD4_DATA6 0x170B1
+ MX6QDL_PAD_SD4_DAT7__SD4_DATA7 0x170B1
+ >;
+ };
+
+ pinctrl_usdhc4_1_200mhz: usdhc4grp-2_200mhz {
+ fsl,pins = <
+ MX6QDL_PAD_SD4_CMD__SD4_CMD 0x170F9
+ MX6QDL_PAD_SD4_CLK__SD4_CLK 0x100F9
+ MX6QDL_PAD_SD4_DAT0__SD4_DATA0 0x170F9
+ MX6QDL_PAD_SD4_DAT1__SD4_DATA1 0x170F9
+ MX6QDL_PAD_SD4_DAT2__SD4_DATA2 0x170F9
+ MX6QDL_PAD_SD4_DAT3__SD4_DATA3 0x170F9
+ MX6QDL_PAD_SD4_DAT4__SD4_DATA4 0x170F9
+ MX6QDL_PAD_SD4_DAT5__SD4_DATA5 0x170F9
+ MX6QDL_PAD_SD4_DAT6__SD4_DATA6 0x170F9
+ MX6QDL_PAD_SD4_DAT7__SD4_DATA7 0x170F9
+ >;
+ };
+};
--
2.6.4
More information about the linux-arm-kernel
mailing list