[PATCH V4] ARM: dts: imx6q-icore-rqs: Add Engicam IMX6 Q7 initial support
Michael Trimarchi
michael at amarulasolutions.com
Thu Dec 24 01:13:10 PST 2015
Hi
Sorry I mess up the email ;). Need to resend. Drop this one
On Thu, Dec 24, 2015 at 10:06 AM, Michael Trimarchi
<michael at amarulasolutions.com> wrote:
> www.engicam.com/en/products/embedded/som/standard/i-core-rqs-m6s-dl-d-q
>
> Signed-off-by: Michael Trimarchi <michael at amarulasolutions.com>
> ---
> Test on top of ARM: dts: imx6q: clean up unused ipu2grp
>
> Changes in v4:
> - update regulator name
> - using flat pins,fsl
> - move iomuxc
> - add X11 license
> - better alphabetic order
>
> Changes in v3:
> - add sgtl audio support
> - add ethernet gigabit tuning
> - use hub reset only in usbhub and not
> in otg vbus
>
> Changes in v2:
> - add the board in alphabetic order
> - remove cpu operating point
> - remove simple-bus and adjust regulaotor
> - add gpios to correct pinctrl
> - remove no mainline binding of gpc
>
> arch/arm/boot/dts/Makefile | 1 +
> arch/arm/boot/dts/imx6q-icore-rqs.dts | 78 ++++++
> arch/arm/boot/dts/imx6qdl-icore-rqs.dtsi | 410 +++++++++++++++++++++++++++++++
> 3 files changed, 489 insertions(+)
> create mode 100644 arch/arm/boot/dts/imx6q-icore-rqs.dts
> create mode 100644 arch/arm/boot/dts/imx6qdl-icore-rqs.dtsi
>
> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> index bb8fa02..7e8f29c 100644
> --- a/arch/arm/boot/dts/Makefile
> +++ b/arch/arm/boot/dts/Makefile
> @@ -312,6 +312,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
> imx6q-gw551x.dtb \
> imx6q-gw552x.dtb \
> imx6q-hummingboard.dtb \
> + imx6q-icore-rqs.dtb \
> imx6q-nitrogen6x.dtb \
> imx6q-phytec-pbab01.dtb \
> imx6q-rex-pro.dtb \
> diff --git a/arch/arm/boot/dts/imx6q-icore-rqs.dts b/arch/arm/boot/dts/imx6q-icore-rqs.dts
> new file mode 100644
> index 0000000..0053188
> --- /dev/null
> +++ b/arch/arm/boot/dts/imx6q-icore-rqs.dts
> @@ -0,0 +1,78 @@
> +/*
> + * Copyright (C) 2015 Amarula Solutions B.V.
> + *
> + * This file is dual-licensed: you can use it either under the terms
> + * of the GPL or the X11 license, at your option. Note that this dual
> + * licensing only applies to this file, and not this project as a
> + * whole.
> + *
> + * a) This file is free software; you can redistribute it and/or
> + * modify it under the terms of the GNU General Public License
> + * version 2 as published by the Free Software Foundation.
> + *
> + * This file is distributed in the hope that it will be useful
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + *
> + * Or, alternatively
> + *
> + * b) Permission is hereby granted, free of charge, to any person
> + * obtaining a copy of this software and associated documentation
> + * files (the "Software"), to deal in the Software without
> + * restriction, including without limitation the rights to use
> + * copy, modify, merge, publish, distribute, sublicense, and/or
> + * sell copies of the Software, and to permit persons to whom the
> + * Software is furnished to do so, subject to the following
> + * conditions:
> + *
> + * The above copyright notice and this permission notice shall be
> + * included in all copies or substantial portions of the Software.
> + *
> + * THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND
> + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
> + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
> + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
> + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY
> + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
> + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
> + * OTHER DEALINGS IN THE SOFTWARE.
> + */
> +
> +/dts-v1/;
> +
> +#include "imx6q.dtsi"
> +#include "imx6qdl-icore-rqs.dtsi"
> +
> +/ {
> + model = "Engicam i.CoreM6 Quad SOM";
> + compatible = "engicam,imx6-icore-rqs", "fsl,imx6q";
> +
> + sound {
> + compatible = "fsl,imx-audio-sgtl5000";
> + model = "imx-audio-sgtl5000";
> + ssi-controller = <&ssi1>;
> + audio-codec = <&codec>;
> + audio-routing =
> + "MIC_IN", "Mic Jack",
> + "Mic Jack", "Mic Bias",
> + "Headphone Jack", "HP_OUT";
> + mux-int-port = <1>;
> + mux-ext-port = <4>;
> + };
> +};
> +
> +&i2c3 {
> + codec: sgtl5000 at 0a {
> + compatible = "fsl,sgtl5000";
> + reg = <0x0a>;
> + clocks = <&clks IMX6QDL_CLK_CKO>;
> + VDDA-supply = <®_2p5v>;
> + VDDIO-supply = <®_3p3v>;
> + VDDD-supply = <®_1p8v>;
> + };
> +};
> +
> +&sata {
> + status = "okay";
> +};
> diff --git a/arch/arm/boot/dts/imx6qdl-icore-rqs.dtsi b/arch/arm/boot/dts/imx6qdl-icore-rqs.dtsi
> new file mode 100644
> index 0000000..b984128
> --- /dev/null
> +++ b/arch/arm/boot/dts/imx6qdl-icore-rqs.dtsi
> @@ -0,0 +1,410 @@
> +/*
> + * Copyright (C) 2015 Amarula Solutions B.V.
> + *
> + * This file is dual-licensed: you can use it either under the terms
> + * of the GPL or the X11 license, at your option. Note that this dual
> + * licensing only applies to this file, and not this project as a
> + * whole.
> + *
> + * a) This file is free software; you can redistribute it and/or
> + * modify it under the terms of the GNU General Public License
> + * version 2 as published by the Free Software Foundation.
> + *
> + * This file is distributed in the hope that it will be useful
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + *
> + * Or, alternatively
> + *
> + * b) Permission is hereby granted, free of charge, to any person
> + * obtaining a copy of this software and associated documentation
> + * files (the "Software"), to deal in the Software without
> + * restriction, including without limitation the rights to use
> + * copy, modify, merge, publish, distribute, sublicense, and/or
> + * sell copies of the Software, and to permit persons to whom the
> + * Software is furnished to do so, subject to the following
> + * conditions:
> + *
> + * The above copyright notice and this permission notice shall be
> + * included in all copies or substantial portions of the Software.
> + *
> + * THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND
> + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
> + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
> + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
> + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY
> + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
> + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
> + * OTHER DEALINGS IN THE SOFTWARE.
> + */
> +
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/clock/imx6qdl-clock.h>
> +
> +/ {
> + memory {
> + reg = <0x10000000 0x80000000>;
> + };
> +
> + reg_1p8v: regulator-1p8v {
> + compatible = "regulator-fixed";
> + regulator-name = "1P8V";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + reg_2p5v: regulator-2p5v {
> + compatible = "regulator-fixed";
> + regulator-name = "2P5V";
> + regulator-min-microvolt = <2500000>;
> + regulator-max-microvolt = <2500000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + reg_3p3v: regulator-3p3v {
> + compatible = "regulator-fixed";
> + regulator-name = "3P3V";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + reg_sd3_vmmc: sd3-vmmc {
> + compatible = "regulator-fixed";
> + regulator-name = "P3V3_SD3_SWITCHED";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + gpio = <&gpio1 4 GPIO_ACTIVE_LOW>;
> + enable-active-high;
> + };
> +
> + reg_sd4_vmmc: sd4-vmmc {
> + compatible = "regulator-fixed";
> + regulator-name = "P3V3_SD4_SWITCHED";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + reg_usb_h1_vbus: usb-h1-vbus {
> + compatible = "regulator-fixed";
> + regulator-name = "usb_h1_vbus";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + reg_usb_otg_vbus: usb-otg-vbus {
> + compatible = "regulator-fixed";
> + regulator-name = "usb_otg_vbus";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + usb_hub: usb-hub {
> + compatible = "smsc,usb3503a";
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_usbhub>;
> + reset-gpios = <&gpio1 6 GPIO_ACTIVE_LOW>;
> + clocks = <&clks IMX6QDL_CLK_LVDS2_GATE>;
> + clock-names = "refclk";
> + };
> +};
> +
> +&clks {
> + assigned-clocks = <&clks IMX6QDL_CLK_LVDS2_SEL>;
> + assigned-clock-parents = <&clks IMX6QDL_CLK_OSC>;
> +};
> +
> +&audmux {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_audmux>;
> + status = "okay";
> +};
> +
> +&fec {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_enet_3>;
> + phy-handle = <ð_phy>;
> + phy-mode = "rgmii";
> + status = "okay";
> + mdio {
> + eth_phy: ethernet-phy {
> + rxc-skew-ps = <1140>;
> + txc-skew-ps = <1140>;
> + txen-skew-ps = <600>;
> + rxdv-skew-ps = <240>;
> + rxd0-skew-ps = <420>;
> + rxd1-skew-ps = <600>;
> + rxd2-skew-ps = <420>;
> + rxd3-skew-ps = <240>;
> + txd0-skew-ps = <60>;
> + txd1-skew-ps = <60>;
> + txd2-skew-ps = <60>;
> + txd3-skew-ps = <240>;
> + };
> + };
> +};
> +
> +&i2c1 {
> + clock-frequency = <100000>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_i2c1_1>;
> + status = "okay";
> +};
> +
> +&i2c2 {
> + clock-frequency = <100000>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_i2c2_2>;
> + status = "okay";
> +};
> +
> +&i2c3 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_i2c3_4>;
> + status = "okay";
> +};
> +
> +&pcie {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_pcie>;
> + reset-gpio = <&gpio3 29 GPIO_ACTIVE_LOW>;
> + status = "okay";
> +};
> +
> +&ssi1 {
> + fsl,mode = "i2s-slave";
> + status = "okay";
> +};
> +
> +&uart4 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_uart4_1>;
> + status = "okay";
> +};
> +
> +&usbh1 {
> + vbus-supply = <®_usb_h1_vbus>;
> + disable-over-current;
> + clocks = <&clks IMX6QDL_CLK_USBOH3>;
> + status = "okay";
> +};
> +
> +&usbotg {
> + vbus-supply = <®_usb_otg_vbus>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_usbotg_2>;
> + disable-over-current;
> + status = "okay";
> +};
> +
> +&usdhc1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_usdhc1_1>;
> + no-1-8-v;
> + status = "okay";
> +};
> +
> +&usdhc3 {
> + pinctrl-names = "default", "state_100mhz", "state_200mhz";
> + pinctrl-0 = <&pinctrl_usdhc3_2>;
> + pinctrl-1 = <&pinctrl_usdhc3_2_100mhz>;
> + pinctrl-2 = <&pinctrl_usdhc3_2_200mhz>;
> + vmcc-supply = <®_sd3_vmmc>;
> + cd-gpios = <&gpio1 1 GPIO_ACTIVE_LOW>;
> + bus-witdh=<4>;
> + no-1-8-v;
> + status = "okay";
> +};
> +
> +&usdhc4 {
> + pinctrl-names = "default", "state_100mhz", "state_200mhz";
> + pinctrl-0 = <&pinctrl_usdhc4_1>;
> + pinctrl-1 = <&pinctrl_usdhc4_1_100mhz>;
> + pinctrl-2 = <&pinctrl_usdhc4_1_200mhz>;
> + vmcc-supply = <®_sd4_vmmc>;
> + bus-witdh=<8>;
> + no-1-8-v;
> + non-removable;
> + status = "okay";
> +};
> +
> +&iomuxc {
> + pinctrl_audmux: audmux {
> + fsl,pins = <
> + MX6QDL_PAD_DISP0_DAT20__AUD4_TXC 0x130b0
> + MX6QDL_PAD_DISP0_DAT21__AUD4_TXD 0x110b0
> + MX6QDL_PAD_DISP0_DAT22__AUD4_TXFS 0x130b0
> + MX6QDL_PAD_DISP0_DAT23__AUD4_RXD 0x130b0
> + >;
> + };
> +
> + pinctrl_enet_3: enetgrp-3 {
> + fsl,pins = <
> + MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x1b0b0
> + MX6QDL_PAD_ENET_MDC__ENET_MDC 0x1b0b0
> + MX6QDL_PAD_RGMII_TXC__RGMII_TXC 0x1b0b0
> + MX6QDL_PAD_RGMII_TD0__RGMII_TD0 0x1b0b0
> + MX6QDL_PAD_RGMII_TD1__RGMII_TD1 0x1b0b0
> + MX6QDL_PAD_RGMII_TD2__RGMII_TD2 0x1b0b0
> + MX6QDL_PAD_RGMII_TD3__RGMII_TD3 0x1b0b0
> + MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL 0x1b0b0
> + MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK 0x1b0b0
> + MX6QDL_PAD_RGMII_RXC__RGMII_RXC 0x1b0b0
> + MX6QDL_PAD_RGMII_RD0__RGMII_RD0 0x1b0b0
> + MX6QDL_PAD_RGMII_RD1__RGMII_RD1 0x1b0b0
> + MX6QDL_PAD_RGMII_RD2__RGMII_RD2 0x1b0b0
> + MX6QDL_PAD_RGMII_RD3__RGMII_RD3 0x1b0b0
> + MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL 0x1b0b0
> + MX6QDL_PAD_ENET_TX_EN__ENET_TX_EN 0x1b0b0
> + >;
> + };
> +
> + pinctrl_i2c1_1: i2c1grp-1 {
> + fsl,pins = <
> + MX6QDL_PAD_EIM_D21__I2C1_SCL 0x4001b8b1
> + MX6QDL_PAD_EIM_D28__I2C1_SDA 0x4001b8b1
> + >;
> + };
> +
> + pinctrl_i2c2_2: i2c2grp-2 {
> + fsl,pins = <
> + MX6QDL_PAD_KEY_COL3__I2C2_SCL 0x4001b8b1
> + MX6QDL_PAD_KEY_ROW3__I2C2_SDA 0x4001b8b1
> + >;
> + };
> +
> + pinctrl_i2c3_4: i2c3grp-4 {
> + fsl,pins = <
> + MX6QDL_PAD_GPIO_5__I2C3_SCL 0x4001b8b1
> + MX6QDL_PAD_EIM_D18__I2C3_SDA 0x4001b8b1
> + MX6QDL_PAD_GPIO_0__CCM_CLKO1 0x130b0
> + >;
> + };
> +
> + pinctrl_pcie: pciegrp {
> + fsl,pins = <
> + MX6QDL_PAD_EIM_D29__GPIO3_IO29 0x1f059 /* PCIe Reset */
> + >;
> + };
> +
> + pinctrl_uart4_1: uart4grp-1 {
> + fsl,pins = <
> + MX6QDL_PAD_KEY_COL0__UART4_TX_DATA 0x1b0b1
> + MX6QDL_PAD_KEY_ROW0__UART4_RX_DATA 0x1b0b1
> + >;
> + };
> +
> + pinctrl_usbhub: usbhubgrp {
> + fsl,pins = <
> + MX6QDL_PAD_GPIO_6__GPIO1_IO06 0x1f059 /* HUB USB Reset */
> + >;
> + };
> +
> + pinctrl_usbotg_2: usbotggrp-2 {
> + fsl,pins = <
> + MX6QDL_PAD_ENET_RX_ER__USB_OTG_ID 0x17059
> + >;
> + };
> +
> + pinctrl_usdhc1_1: usdhc1grp-1 {
> + fsl,pins = <
> + MX6QDL_PAD_SD1_CMD__SD1_CMD 0x17071
> + MX6QDL_PAD_SD1_CLK__SD1_CLK 0x10071
> + MX6QDL_PAD_SD1_DAT0__SD1_DATA0 0x17071
> + MX6QDL_PAD_SD1_DAT1__SD1_DATA1 0x17071
> + MX6QDL_PAD_SD1_DAT2__SD1_DATA2 0x17071
> + MX6QDL_PAD_SD1_DAT3__SD1_DATA3 0x17071
> + >;
> + };
> +
> + pinctrl_usdhc3_2: usdhc3grp-2 {
> + fsl,pins = <
> + MX6QDL_PAD_SD3_CMD__SD3_CMD 0x17070
> + MX6QDL_PAD_SD3_CLK__SD3_CLK 0x10070
> + MX6QDL_PAD_SD3_DAT0__SD3_DATA0 0x17070
> + MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x17070
> + MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x17070
> + MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x17070
> + MX6QDL_PAD_GPIO_1__GPIO1_IO01 0x1f059 /* CD */
> + MX6QDL_PAD_GPIO_4__GPIO1_IO04 0x1f059 /* PWR */
> + >;
> + };
> +
> + pinctrl_usdhc3_2_100mhz: usdhc3grp-2_100mhz {
> + fsl,pins = <
> + MX6QDL_PAD_SD3_CMD__SD3_CMD 0x170B1
> + MX6QDL_PAD_SD3_CLK__SD3_CLK 0x100B1
> + MX6QDL_PAD_SD3_DAT0__SD3_DATA0 0x170B1
> + MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x170B1
> + MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x170B1
> + MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x170B1
> + >;
> + };
> +
> + pinctrl_usdhc3_2_200mhz: usdhc3grp-2_200mhz {
> + fsl,pins = <
> + MX6QDL_PAD_SD3_CMD__SD3_CMD 0x170F9
> + MX6QDL_PAD_SD3_CLK__SD3_CLK 0x100F9
> + MX6QDL_PAD_SD3_DAT0__SD3_DATA0 0x170F9
> + MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x170F9
> + MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x170F9
> + MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x170F9
> + >;
> + };
> +
> + pinctrl_usdhc4_1: usdhc4grp-1 {
> + fsl,pins = <
> + MX6QDL_PAD_SD4_CMD__SD4_CMD 0x17070
> + MX6QDL_PAD_SD4_CLK__SD4_CLK 0x10070
> + MX6QDL_PAD_SD4_DAT0__SD4_DATA0 0x17070
> + MX6QDL_PAD_SD4_DAT1__SD4_DATA1 0x17070
> + MX6QDL_PAD_SD4_DAT2__SD4_DATA2 0x17070
> + MX6QDL_PAD_SD4_DAT3__SD4_DATA3 0x17070
> + MX6QDL_PAD_SD4_DAT4__SD4_DATA4 0x17070
> + MX6QDL_PAD_SD4_DAT5__SD4_DATA5 0x17070
> + MX6QDL_PAD_SD4_DAT6__SD4_DATA6 0x17070
> + MX6QDL_PAD_SD4_DAT7__SD4_DATA7 0x17070
> + >;
> + };
> +
> + pinctrl_usdhc4_1_100mhz: usdhc4grp-1_100mhz {
> + fsl,pins = <
> + MX6QDL_PAD_SD4_CMD__SD4_CMD 0x170B1
> + MX6QDL_PAD_SD4_CLK__SD4_CLK 0x100B1
> + MX6QDL_PAD_SD4_DAT0__SD4_DATA0 0x170B1
> + MX6QDL_PAD_SD4_DAT1__SD4_DATA1 0x170B1
> + MX6QDL_PAD_SD4_DAT2__SD4_DATA2 0x170B1
> + MX6QDL_PAD_SD4_DAT3__SD4_DATA3 0x170B1
> + MX6QDL_PAD_SD4_DAT4__SD4_DATA4 0x170B1
> + MX6QDL_PAD_SD4_DAT5__SD4_DATA5 0x170B1
> + MX6QDL_PAD_SD4_DAT6__SD4_DATA6 0x170B1
> + MX6QDL_PAD_SD4_DAT7__SD4_DATA7 0x170B1
> + >;
> + };
> +
> + pinctrl_usdhc4_1_200mhz: usdhc4grp-2_200mhz {
> + fsl,pins = <
> + MX6QDL_PAD_SD4_CMD__SD4_CMD 0x170F9
> + MX6QDL_PAD_SD4_CLK__SD4_CLK 0x100F9
> + MX6QDL_PAD_SD4_DAT0__SD4_DATA0 0x170F9
> + MX6QDL_PAD_SD4_DAT1__SD4_DATA1 0x170F9
> + MX6QDL_PAD_SD4_DAT2__SD4_DATA2 0x170F9
> + MX6QDL_PAD_SD4_DAT3__SD4_DATA3 0x170F9
> + MX6QDL_PAD_SD4_DAT4__SD4_DATA4 0x170F9
> + MX6QDL_PAD_SD4_DAT5__SD4_DATA5 0x170F9
> + MX6QDL_PAD_SD4_DAT6__SD4_DATA6 0x170F9
> + MX6QDL_PAD_SD4_DAT7__SD4_DATA7 0x170F9
> + >;
> + };
> +};
> --
> 2.6.4
>
> arch/arm/boot/dts/Makefile | 1 +
> arch/arm/boot/dts/imx6q-icore-rqs.dts | 78 ++++++
> arch/arm/boot/dts/imx6qdl-icore-rqs.dtsi | 410 +++++++++++++++++++++++++++++++
> 3 files changed, 489 insertions(+)
> create mode 100644 arch/arm/boot/dts/imx6q-icore-rqs.dts
> create mode 100644 arch/arm/boot/dts/imx6qdl-icore-rqs.dtsi
>
> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> index bb8fa02..7e8f29c 100644
> --- a/arch/arm/boot/dts/Makefile
> +++ b/arch/arm/boot/dts/Makefile
> @@ -312,6 +312,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
> imx6q-gw551x.dtb \
> imx6q-gw552x.dtb \
> imx6q-hummingboard.dtb \
> + imx6q-icore-rqs.dtb \
> imx6q-nitrogen6x.dtb \
> imx6q-phytec-pbab01.dtb \
> imx6q-rex-pro.dtb \
> diff --git a/arch/arm/boot/dts/imx6q-icore-rqs.dts b/arch/arm/boot/dts/imx6q-icore-rqs.dts
> new file mode 100644
> index 0000000..0053188
> --- /dev/null
> +++ b/arch/arm/boot/dts/imx6q-icore-rqs.dts
> @@ -0,0 +1,78 @@
> +/*
> + * Copyright (C) 2015 Amarula Solutions B.V.
> + *
> + * This file is dual-licensed: you can use it either under the terms
> + * of the GPL or the X11 license, at your option. Note that this dual
> + * licensing only applies to this file, and not this project as a
> + * whole.
> + *
> + * a) This file is free software; you can redistribute it and/or
> + * modify it under the terms of the GNU General Public License
> + * version 2 as published by the Free Software Foundation.
> + *
> + * This file is distributed in the hope that it will be useful
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + *
> + * Or, alternatively
> + *
> + * b) Permission is hereby granted, free of charge, to any person
> + * obtaining a copy of this software and associated documentation
> + * files (the "Software"), to deal in the Software without
> + * restriction, including without limitation the rights to use
> + * copy, modify, merge, publish, distribute, sublicense, and/or
> + * sell copies of the Software, and to permit persons to whom the
> + * Software is furnished to do so, subject to the following
> + * conditions:
> + *
> + * The above copyright notice and this permission notice shall be
> + * included in all copies or substantial portions of the Software.
> + *
> + * THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND
> + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
> + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
> + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
> + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY
> + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
> + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
> + * OTHER DEALINGS IN THE SOFTWARE.
> + */
> +
> +/dts-v1/;
> +
> +#include "imx6q.dtsi"
> +#include "imx6qdl-icore-rqs.dtsi"
> +
> +/ {
> + model = "Engicam i.CoreM6 Quad SOM";
> + compatible = "engicam,imx6-icore-rqs", "fsl,imx6q";
> +
> + sound {
> + compatible = "fsl,imx-audio-sgtl5000";
> + model = "imx-audio-sgtl5000";
> + ssi-controller = <&ssi1>;
> + audio-codec = <&codec>;
> + audio-routing =
> + "MIC_IN", "Mic Jack",
> + "Mic Jack", "Mic Bias",
> + "Headphone Jack", "HP_OUT";
> + mux-int-port = <1>;
> + mux-ext-port = <4>;
> + };
> +};
> +
> +&i2c3 {
> + codec: sgtl5000 at 0a {
> + compatible = "fsl,sgtl5000";
> + reg = <0x0a>;
> + clocks = <&clks IMX6QDL_CLK_CKO>;
> + VDDA-supply = <®_2p5v>;
> + VDDIO-supply = <®_3p3v>;
> + VDDD-supply = <®_1p8v>;
> + };
> +};
> +
> +&sata {
> + status = "okay";
> +};
> diff --git a/arch/arm/boot/dts/imx6qdl-icore-rqs.dtsi b/arch/arm/boot/dts/imx6qdl-icore-rqs.dtsi
> new file mode 100644
> index 0000000..b984128
> --- /dev/null
> +++ b/arch/arm/boot/dts/imx6qdl-icore-rqs.dtsi
> @@ -0,0 +1,410 @@
> +/*
> + * Copyright (C) 2015 Amarula Solutions B.V.
> + *
> + * This file is dual-licensed: you can use it either under the terms
> + * of the GPL or the X11 license, at your option. Note that this dual
> + * licensing only applies to this file, and not this project as a
> + * whole.
> + *
> + * a) This file is free software; you can redistribute it and/or
> + * modify it under the terms of the GNU General Public License
> + * version 2 as published by the Free Software Foundation.
> + *
> + * This file is distributed in the hope that it will be useful
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + *
> + * Or, alternatively
> + *
> + * b) Permission is hereby granted, free of charge, to any person
> + * obtaining a copy of this software and associated documentation
> + * files (the "Software"), to deal in the Software without
> + * restriction, including without limitation the rights to use
> + * copy, modify, merge, publish, distribute, sublicense, and/or
> + * sell copies of the Software, and to permit persons to whom the
> + * Software is furnished to do so, subject to the following
> + * conditions:
> + *
> + * The above copyright notice and this permission notice shall be
> + * included in all copies or substantial portions of the Software.
> + *
> + * THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND
> + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
> + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
> + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
> + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY
> + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
> + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
> + * OTHER DEALINGS IN THE SOFTWARE.
> + */
> +
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/clock/imx6qdl-clock.h>
> +
> +/ {
> + memory {
> + reg = <0x10000000 0x80000000>;
> + };
> +
> + reg_1p8v: regulator-1p8v {
> + compatible = "regulator-fixed";
> + regulator-name = "1P8V";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + reg_2p5v: regulator-2p5v {
> + compatible = "regulator-fixed";
> + regulator-name = "2P5V";
> + regulator-min-microvolt = <2500000>;
> + regulator-max-microvolt = <2500000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + reg_3p3v: regulator-3p3v {
> + compatible = "regulator-fixed";
> + regulator-name = "3P3V";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + reg_sd3_vmmc: sd3-vmmc {
> + compatible = "regulator-fixed";
> + regulator-name = "P3V3_SD3_SWITCHED";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + gpio = <&gpio1 4 GPIO_ACTIVE_LOW>;
> + enable-active-high;
> + };
> +
> + reg_sd4_vmmc: sd4-vmmc {
> + compatible = "regulator-fixed";
> + regulator-name = "P3V3_SD4_SWITCHED";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + reg_usb_h1_vbus: usb-h1-vbus {
> + compatible = "regulator-fixed";
> + regulator-name = "usb_h1_vbus";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + reg_usb_otg_vbus: usb-otg-vbus {
> + compatible = "regulator-fixed";
> + regulator-name = "usb_otg_vbus";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + usb_hub: usb-hub {
> + compatible = "smsc,usb3503a";
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_usbhub>;
> + reset-gpios = <&gpio1 6 GPIO_ACTIVE_LOW>;
> + clocks = <&clks IMX6QDL_CLK_LVDS2_GATE>;
> + clock-names = "refclk";
> + };
> +};
> +
> +&clks {
> + assigned-clocks = <&clks IMX6QDL_CLK_LVDS2_SEL>;
> + assigned-clock-parents = <&clks IMX6QDL_CLK_OSC>;
> +};
> +
> +&audmux {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_audmux>;
> + status = "okay";
> +};
> +
> +&fec {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_enet_3>;
> + phy-handle = <ð_phy>;
> + phy-mode = "rgmii";
> + status = "okay";
> + mdio {
> + eth_phy: ethernet-phy {
> + rxc-skew-ps = <1140>;
> + txc-skew-ps = <1140>;
> + txen-skew-ps = <600>;
> + rxdv-skew-ps = <240>;
> + rxd0-skew-ps = <420>;
> + rxd1-skew-ps = <600>;
> + rxd2-skew-ps = <420>;
> + rxd3-skew-ps = <240>;
> + txd0-skew-ps = <60>;
> + txd1-skew-ps = <60>;
> + txd2-skew-ps = <60>;
> + txd3-skew-ps = <240>;
> + };
> + };
> +};
> +
> +&i2c1 {
> + clock-frequency = <100000>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_i2c1_1>;
> + status = "okay";
> +};
> +
> +&i2c2 {
> + clock-frequency = <100000>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_i2c2_2>;
> + status = "okay";
> +};
> +
> +&i2c3 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_i2c3_4>;
> + status = "okay";
> +};
> +
> +&pcie {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_pcie>;
> + reset-gpio = <&gpio3 29 GPIO_ACTIVE_LOW>;
> + status = "okay";
> +};
> +
> +&ssi1 {
> + fsl,mode = "i2s-slave";
> + status = "okay";
> +};
> +
> +&uart4 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_uart4_1>;
> + status = "okay";
> +};
> +
> +&usbh1 {
> + vbus-supply = <®_usb_h1_vbus>;
> + disable-over-current;
> + clocks = <&clks IMX6QDL_CLK_USBOH3>;
> + status = "okay";
> +};
> +
> +&usbotg {
> + vbus-supply = <®_usb_otg_vbus>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_usbotg_2>;
> + disable-over-current;
> + status = "okay";
> +};
> +
> +&usdhc1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_usdhc1_1>;
> + no-1-8-v;
> + status = "okay";
> +};
> +
> +&usdhc3 {
> + pinctrl-names = "default", "state_100mhz", "state_200mhz";
> + pinctrl-0 = <&pinctrl_usdhc3_2>;
> + pinctrl-1 = <&pinctrl_usdhc3_2_100mhz>;
> + pinctrl-2 = <&pinctrl_usdhc3_2_200mhz>;
> + vmcc-supply = <®_sd3_vmmc>;
> + cd-gpios = <&gpio1 1 GPIO_ACTIVE_LOW>;
> + bus-witdh=<4>;
> + no-1-8-v;
> + status = "okay";
> +};
> +
> +&usdhc4 {
> + pinctrl-names = "default", "state_100mhz", "state_200mhz";
> + pinctrl-0 = <&pinctrl_usdhc4_1>;
> + pinctrl-1 = <&pinctrl_usdhc4_1_100mhz>;
> + pinctrl-2 = <&pinctrl_usdhc4_1_200mhz>;
> + vmcc-supply = <®_sd4_vmmc>;
> + bus-witdh=<8>;
> + no-1-8-v;
> + non-removable;
> + status = "okay";
> +};
> +
> +&iomuxc {
> + pinctrl_audmux: audmux {
> + fsl,pins = <
> + MX6QDL_PAD_DISP0_DAT20__AUD4_TXC 0x130b0
> + MX6QDL_PAD_DISP0_DAT21__AUD4_TXD 0x110b0
> + MX6QDL_PAD_DISP0_DAT22__AUD4_TXFS 0x130b0
> + MX6QDL_PAD_DISP0_DAT23__AUD4_RXD 0x130b0
> + >;
> + };
> +
> + pinctrl_enet_3: enetgrp-3 {
> + fsl,pins = <
> + MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x1b0b0
> + MX6QDL_PAD_ENET_MDC__ENET_MDC 0x1b0b0
> + MX6QDL_PAD_RGMII_TXC__RGMII_TXC 0x1b0b0
> + MX6QDL_PAD_RGMII_TD0__RGMII_TD0 0x1b0b0
> + MX6QDL_PAD_RGMII_TD1__RGMII_TD1 0x1b0b0
> + MX6QDL_PAD_RGMII_TD2__RGMII_TD2 0x1b0b0
> + MX6QDL_PAD_RGMII_TD3__RGMII_TD3 0x1b0b0
> + MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL 0x1b0b0
> + MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK 0x1b0b0
> + MX6QDL_PAD_RGMII_RXC__RGMII_RXC 0x1b0b0
> + MX6QDL_PAD_RGMII_RD0__RGMII_RD0 0x1b0b0
> + MX6QDL_PAD_RGMII_RD1__RGMII_RD1 0x1b0b0
> + MX6QDL_PAD_RGMII_RD2__RGMII_RD2 0x1b0b0
> + MX6QDL_PAD_RGMII_RD3__RGMII_RD3 0x1b0b0
> + MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL 0x1b0b0
> + MX6QDL_PAD_ENET_TX_EN__ENET_TX_EN 0x1b0b0
> + >;
> + };
> +
> + pinctrl_i2c1_1: i2c1grp-1 {
> + fsl,pins = <
> + MX6QDL_PAD_EIM_D21__I2C1_SCL 0x4001b8b1
> + MX6QDL_PAD_EIM_D28__I2C1_SDA 0x4001b8b1
> + >;
> + };
> +
> + pinctrl_i2c2_2: i2c2grp-2 {
> + fsl,pins = <
> + MX6QDL_PAD_KEY_COL3__I2C2_SCL 0x4001b8b1
> + MX6QDL_PAD_KEY_ROW3__I2C2_SDA 0x4001b8b1
> + >;
> + };
> +
> + pinctrl_i2c3_4: i2c3grp-4 {
> + fsl,pins = <
> + MX6QDL_PAD_GPIO_5__I2C3_SCL 0x4001b8b1
> + MX6QDL_PAD_EIM_D18__I2C3_SDA 0x4001b8b1
> + MX6QDL_PAD_GPIO_0__CCM_CLKO1 0x130b0
> + >;
> + };
> +
> + pinctrl_pcie: pciegrp {
> + fsl,pins = <
> + MX6QDL_PAD_EIM_D29__GPIO3_IO29 0x1f059 /* PCIe Reset */
> + >;
> + };
> +
> + pinctrl_uart4_1: uart4grp-1 {
> + fsl,pins = <
> + MX6QDL_PAD_KEY_COL0__UART4_TX_DATA 0x1b0b1
> + MX6QDL_PAD_KEY_ROW0__UART4_RX_DATA 0x1b0b1
> + >;
> + };
> +
> + pinctrl_usbhub: usbhubgrp {
> + fsl,pins = <
> + MX6QDL_PAD_GPIO_6__GPIO1_IO06 0x1f059 /* HUB USB Reset */
> + >;
> + };
> +
> + pinctrl_usbotg_2: usbotggrp-2 {
> + fsl,pins = <
> + MX6QDL_PAD_ENET_RX_ER__USB_OTG_ID 0x17059
> + >;
> + };
> +
> + pinctrl_usdhc1_1: usdhc1grp-1 {
> + fsl,pins = <
> + MX6QDL_PAD_SD1_CMD__SD1_CMD 0x17071
> + MX6QDL_PAD_SD1_CLK__SD1_CLK 0x10071
> + MX6QDL_PAD_SD1_DAT0__SD1_DATA0 0x17071
> + MX6QDL_PAD_SD1_DAT1__SD1_DATA1 0x17071
> + MX6QDL_PAD_SD1_DAT2__SD1_DATA2 0x17071
> + MX6QDL_PAD_SD1_DAT3__SD1_DATA3 0x17071
> + >;
> + };
> +
> + pinctrl_usdhc3_2: usdhc3grp-2 {
> + fsl,pins = <
> + MX6QDL_PAD_SD3_CMD__SD3_CMD 0x17070
> + MX6QDL_PAD_SD3_CLK__SD3_CLK 0x10070
> + MX6QDL_PAD_SD3_DAT0__SD3_DATA0 0x17070
> + MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x17070
> + MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x17070
> + MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x17070
> + MX6QDL_PAD_GPIO_1__GPIO1_IO01 0x1f059 /* CD */
> + MX6QDL_PAD_GPIO_4__GPIO1_IO04 0x1f059 /* PWR */
> + >;
> + };
> +
> + pinctrl_usdhc3_2_100mhz: usdhc3grp-2_100mhz {
> + fsl,pins = <
> + MX6QDL_PAD_SD3_CMD__SD3_CMD 0x170B1
> + MX6QDL_PAD_SD3_CLK__SD3_CLK 0x100B1
> + MX6QDL_PAD_SD3_DAT0__SD3_DATA0 0x170B1
> + MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x170B1
> + MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x170B1
> + MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x170B1
> + >;
> + };
> +
> + pinctrl_usdhc3_2_200mhz: usdhc3grp-2_200mhz {
> + fsl,pins = <
> + MX6QDL_PAD_SD3_CMD__SD3_CMD 0x170F9
> + MX6QDL_PAD_SD3_CLK__SD3_CLK 0x100F9
> + MX6QDL_PAD_SD3_DAT0__SD3_DATA0 0x170F9
> + MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x170F9
> + MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x170F9
> + MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x170F9
> + >;
> + };
> +
> + pinctrl_usdhc4_1: usdhc4grp-1 {
> + fsl,pins = <
> + MX6QDL_PAD_SD4_CMD__SD4_CMD 0x17070
> + MX6QDL_PAD_SD4_CLK__SD4_CLK 0x10070
> + MX6QDL_PAD_SD4_DAT0__SD4_DATA0 0x17070
> + MX6QDL_PAD_SD4_DAT1__SD4_DATA1 0x17070
> + MX6QDL_PAD_SD4_DAT2__SD4_DATA2 0x17070
> + MX6QDL_PAD_SD4_DAT3__SD4_DATA3 0x17070
> + MX6QDL_PAD_SD4_DAT4__SD4_DATA4 0x17070
> + MX6QDL_PAD_SD4_DAT5__SD4_DATA5 0x17070
> + MX6QDL_PAD_SD4_DAT6__SD4_DATA6 0x17070
> + MX6QDL_PAD_SD4_DAT7__SD4_DATA7 0x17070
> + >;
> + };
> +
> + pinctrl_usdhc4_1_100mhz: usdhc4grp-1_100mhz {
> + fsl,pins = <
> + MX6QDL_PAD_SD4_CMD__SD4_CMD 0x170B1
> + MX6QDL_PAD_SD4_CLK__SD4_CLK 0x100B1
> + MX6QDL_PAD_SD4_DAT0__SD4_DATA0 0x170B1
> + MX6QDL_PAD_SD4_DAT1__SD4_DATA1 0x170B1
> + MX6QDL_PAD_SD4_DAT2__SD4_DATA2 0x170B1
> + MX6QDL_PAD_SD4_DAT3__SD4_DATA3 0x170B1
> + MX6QDL_PAD_SD4_DAT4__SD4_DATA4 0x170B1
> + MX6QDL_PAD_SD4_DAT5__SD4_DATA5 0x170B1
> + MX6QDL_PAD_SD4_DAT6__SD4_DATA6 0x170B1
> + MX6QDL_PAD_SD4_DAT7__SD4_DATA7 0x170B1
> + >;
> + };
> +
> + pinctrl_usdhc4_1_200mhz: usdhc4grp-2_200mhz {
> + fsl,pins = <
> + MX6QDL_PAD_SD4_CMD__SD4_CMD 0x170F9
> + MX6QDL_PAD_SD4_CLK__SD4_CLK 0x100F9
> + MX6QDL_PAD_SD4_DAT0__SD4_DATA0 0x170F9
> + MX6QDL_PAD_SD4_DAT1__SD4_DATA1 0x170F9
> + MX6QDL_PAD_SD4_DAT2__SD4_DATA2 0x170F9
> + MX6QDL_PAD_SD4_DAT3__SD4_DATA3 0x170F9
> + MX6QDL_PAD_SD4_DAT4__SD4_DATA4 0x170F9
> + MX6QDL_PAD_SD4_DAT5__SD4_DATA5 0x170F9
> + MX6QDL_PAD_SD4_DAT6__SD4_DATA6 0x170F9
> + MX6QDL_PAD_SD4_DAT7__SD4_DATA7 0x170F9
> + >;
> + };
> +};
> --
> 2.6.4
>
> --
> | Michael Nazzareno Trimarchi Amarula Solutions BV |
> | COO - Founder Cruquiuskade 47 |
> | +31(0)851119172 Amsterdam 1018 AM NL |
> | [`as] http://www.amarulasolutions.com |
--
| Michael Nazzareno Trimarchi Amarula Solutions BV |
| COO - Founder Cruquiuskade 47 |
| +31(0)851119172 Amsterdam 1018 AM NL |
| [`as] http://www.amarulasolutions.com |
More information about the linux-arm-kernel
mailing list