[PATCH] Remove the support for the RSI EWS board
Nicolas Ferre
nicolas.ferre at atmel.com
Fri Sep 19 04:12:16 PDT 2014
On 19/09/2014 13:02, Josef Holzmayr :
> The platform is end of life/support and should not clutter
> the mach-at91 directory with non-DT files. It is therefore
> removed.
>
> Signed-off-by: Josef Holzmayr <holzmayr at rsi-elektrotechnik.de>
Ok, thanks for having take the action Josef. So obviously:
Acked-by: Nicolas Ferre <nicolas.ferre at atmel.com>
I'll try to queue it in our at91-3.18-soc branch.
Best regards,
> ---
> arch/arm/mach-at91/Kconfig.non_dt | 6 -
> arch/arm/mach-at91/Makefile | 1 -
> arch/arm/mach-at91/board-rsi-ews.c | 232 -------------------------------------
> 3 files changed, 239 deletions(-)
> delete mode 100644 arch/arm/mach-at91/board-rsi-ews.c
>
> diff --git a/arch/arm/mach-at91/Kconfig.non_dt b/arch/arm/mach-at91/Kconfig.non_dt
> index 44ace32..836d275 100644
> --- a/arch/arm/mach-at91/Kconfig.non_dt
> +++ b/arch/arm/mach-at91/Kconfig.non_dt
> @@ -132,12 +132,6 @@ config MACH_ECO920
> bool "eco920"
> help
> Select this if you are using the eco920 board
> -
> -config MACH_RSI_EWS
> - bool "RSI Embedded Webserver"
> - depends on ARCH_AT91RM9200
> - help
> - Select this if you are using RSIs EWS board.
> endif
>
> # ----------------------------------------------------------
> diff --git a/arch/arm/mach-at91/Makefile b/arch/arm/mach-at91/Makefile
> index 78e9cec..b74db03 100644
> --- a/arch/arm/mach-at91/Makefile
> +++ b/arch/arm/mach-at91/Makefile
> @@ -46,7 +46,6 @@ obj-$(CONFIG_MACH_ECBAT91) += board-ecbat91.o
> obj-$(CONFIG_MACH_YL9200) += board-yl-9200.o
> obj-$(CONFIG_MACH_CPUAT91) += board-cpuat91.o
> obj-$(CONFIG_MACH_ECO920) += board-eco920.o
> -obj-$(CONFIG_MACH_RSI_EWS) += board-rsi-ews.o
>
> # AT91SAM9260 board-specific support
> obj-$(CONFIG_MACH_AT91SAM9260EK) += board-sam9260ek.o
> diff --git a/arch/arm/mach-at91/board-rsi-ews.c b/arch/arm/mach-at91/board-rsi-ews.c
> deleted file mode 100644
> index f28e8b7..0000000
> --- a/arch/arm/mach-at91/board-rsi-ews.c
> +++ /dev/null
> @@ -1,232 +0,0 @@
> -/*
> - * board-rsi-ews.c
> - *
> - * Copyright (C)
> - * 2005 SAN People,
> - * 2008-2011 R-S-I Elektrotechnik GmbH & Co. KG
> - *
> - * Licensed under GPLv2 or later.
> - */
> -
> -#include <linux/types.h>
> -#include <linux/init.h>
> -#include <linux/mm.h>
> -#include <linux/module.h>
> -#include <linux/platform_device.h>
> -#include <linux/spi/spi.h>
> -#include <linux/mtd/physmap.h>
> -
> -#include <asm/setup.h>
> -#include <asm/mach-types.h>
> -#include <asm/irq.h>
> -
> -#include <asm/mach/arch.h>
> -#include <asm/mach/map.h>
> -#include <asm/mach/irq.h>
> -
> -#include <mach/hardware.h>
> -
> -#include <linux/gpio.h>
> -
> -#include "at91_aic.h"
> -#include "board.h"
> -#include "generic.h"
> -#include "gpio.h"
> -
> -static void __init rsi_ews_init_early(void)
> -{
> - /* Initialize processor: 18.432 MHz crystal */
> - at91_initialize(18432000);
> -}
> -
> -/*
> - * Ethernet
> - */
> -static struct macb_platform_data rsi_ews_eth_data __initdata = {
> - .phy_irq_pin = AT91_PIN_PC4,
> - .is_rmii = 1,
> -};
> -
> -/*
> - * USB Host
> - */
> -static struct at91_usbh_data rsi_ews_usbh_data __initdata = {
> - .ports = 1,
> - .vbus_pin = {-EINVAL, -EINVAL},
> - .overcurrent_pin= {-EINVAL, -EINVAL},
> -};
> -
> -/*
> - * SD/MC
> - */
> -static struct mci_platform_data __initdata rsi_ews_mci0_data = {
> - .slot[0] = {
> - .bus_width = 4,
> - .detect_pin = AT91_PIN_PB27,
> - .wp_pin = AT91_PIN_PB29,
> - },
> -};
> -
> -/*
> - * I2C
> - */
> -static struct i2c_board_info rsi_ews_i2c_devices[] __initdata = {
> - {
> - I2C_BOARD_INFO("ds1337", 0x68),
> - },
> - {
> - I2C_BOARD_INFO("24c01", 0x50),
> - }
> -};
> -
> -/*
> - * LEDs
> - */
> -static struct gpio_led rsi_ews_leds[] = {
> - {
> - .name = "led0",
> - .gpio = AT91_PIN_PB6,
> - .active_low = 0,
> - },
> - {
> - .name = "led1",
> - .gpio = AT91_PIN_PB7,
> - .active_low = 0,
> - },
> - {
> - .name = "led2",
> - .gpio = AT91_PIN_PB8,
> - .active_low = 0,
> - },
> - {
> - .name = "led3",
> - .gpio = AT91_PIN_PB9,
> - .active_low = 0,
> - },
> -};
> -
> -/*
> - * DataFlash
> - */
> -static struct spi_board_info rsi_ews_spi_devices[] = {
> - { /* DataFlash chip 1*/
> - .modalias = "mtd_dataflash",
> - .chip_select = 0,
> - .max_speed_hz = 5 * 1000 * 1000,
> - },
> - { /* DataFlash chip 2*/
> - .modalias = "mtd_dataflash",
> - .chip_select = 1,
> - .max_speed_hz = 5 * 1000 * 1000,
> - },
> -};
> -
> -/*
> - * NOR flash
> - */
> -static struct mtd_partition rsiews_nor_partitions[] = {
> - {
> - .name = "boot",
> - .offset = 0,
> - .size = 3 * SZ_128K,
> - .mask_flags = MTD_WRITEABLE
> - },
> - {
> - .name = "kernel",
> - .offset = MTDPART_OFS_NXTBLK,
> - .size = SZ_2M - (3 * SZ_128K)
> - },
> - {
> - .name = "root",
> - .offset = MTDPART_OFS_NXTBLK,
> - .size = SZ_8M
> - },
> - {
> - .name = "kernelupd",
> - .offset = MTDPART_OFS_NXTBLK,
> - .size = 3 * SZ_512K,
> - .mask_flags = MTD_WRITEABLE
> - },
> - {
> - .name = "rootupd",
> - .offset = MTDPART_OFS_NXTBLK,
> - .size = 9 * SZ_512K,
> - .mask_flags = MTD_WRITEABLE
> - },
> -};
> -
> -static struct physmap_flash_data rsiews_nor_data = {
> - .width = 2,
> - .parts = rsiews_nor_partitions,
> - .nr_parts = ARRAY_SIZE(rsiews_nor_partitions),
> -};
> -
> -#define NOR_BASE AT91_CHIPSELECT_0
> -#define NOR_SIZE SZ_16M
> -
> -static struct resource nor_flash_resources[] = {
> - {
> - .start = NOR_BASE,
> - .end = NOR_BASE + NOR_SIZE - 1,
> - .flags = IORESOURCE_MEM,
> - }
> -};
> -
> -static struct platform_device rsiews_nor_flash = {
> - .name = "physmap-flash",
> - .id = 0,
> - .dev = {
> - .platform_data = &rsiews_nor_data,
> - },
> - .resource = nor_flash_resources,
> - .num_resources = ARRAY_SIZE(nor_flash_resources),
> -};
> -
> -/*
> - * Init Func
> - */
> -static void __init rsi_ews_board_init(void)
> -{
> - /* Serial */
> - /* DBGU on ttyS0. (Rx & Tx only) */
> - /* This one is for debugging */
> - at91_register_uart(0, 0, 0);
> -
> - /* USART1 on ttyS2. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */
> - /* Dialin/-out modem interface */
> - at91_register_uart(AT91RM9200_ID_US1, 2, ATMEL_UART_CTS | ATMEL_UART_RTS
> - | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD
> - | ATMEL_UART_RI);
> -
> - /* USART3 on ttyS4. (Rx, Tx, RTS) */
> - /* RS485 communication */
> - at91_register_uart(AT91RM9200_ID_US3, 4, ATMEL_UART_RTS);
> - at91_add_device_serial();
> - at91_set_gpio_output(AT91_PIN_PA21, 0);
> - /* Ethernet */
> - at91_add_device_eth(&rsi_ews_eth_data);
> - /* USB Host */
> - at91_add_device_usbh(&rsi_ews_usbh_data);
> - /* I2C */
> - at91_add_device_i2c(rsi_ews_i2c_devices,
> - ARRAY_SIZE(rsi_ews_i2c_devices));
> - /* SPI */
> - at91_add_device_spi(rsi_ews_spi_devices,
> - ARRAY_SIZE(rsi_ews_spi_devices));
> - /* MMC */
> - at91_add_device_mci(0, &rsi_ews_mci0_data);
> - /* NOR Flash */
> - platform_device_register(&rsiews_nor_flash);
> - /* LEDs */
> - at91_gpio_leds(rsi_ews_leds, ARRAY_SIZE(rsi_ews_leds));
> -}
> -
> -MACHINE_START(RSI_EWS, "RSI EWS")
> - /* Maintainer: Josef Holzmayr <holzmayr at rsi-elektrotechnik.de> */
> - .init_time = at91rm9200_timer_init,
> - .map_io = at91_map_io,
> - .handle_irq = at91_aic_handle_irq,
> - .init_early = rsi_ews_init_early,
> - .init_irq = at91_init_irq_default,
> - .init_machine = rsi_ews_board_init,
> -MACHINE_END
>
--
Nicolas Ferre
More information about the linux-arm-kernel
mailing list