[PATCH] Remove the support for the RSI EWS board
Josef Holzmayr
holzmayr at rsi-elektrotechnik.de
Fri Sep 19 04:02:26 PDT 2014
The platform is end of life/support and should not clutter
the mach-at91 directory with non-DT files. It is therefore
removed.
Signed-off-by: Josef Holzmayr <holzmayr at rsi-elektrotechnik.de>
---
arch/arm/mach-at91/Kconfig.non_dt | 6 -
arch/arm/mach-at91/Makefile | 1 -
arch/arm/mach-at91/board-rsi-ews.c | 232 -------------------------------------
3 files changed, 239 deletions(-)
delete mode 100644 arch/arm/mach-at91/board-rsi-ews.c
diff --git a/arch/arm/mach-at91/Kconfig.non_dt b/arch/arm/mach-at91/Kconfig.non_dt
index 44ace32..836d275 100644
--- a/arch/arm/mach-at91/Kconfig.non_dt
+++ b/arch/arm/mach-at91/Kconfig.non_dt
@@ -132,12 +132,6 @@ config MACH_ECO920
bool "eco920"
help
Select this if you are using the eco920 board
-
-config MACH_RSI_EWS
- bool "RSI Embedded Webserver"
- depends on ARCH_AT91RM9200
- help
- Select this if you are using RSIs EWS board.
endif
# ----------------------------------------------------------
diff --git a/arch/arm/mach-at91/Makefile b/arch/arm/mach-at91/Makefile
index 78e9cec..b74db03 100644
--- a/arch/arm/mach-at91/Makefile
+++ b/arch/arm/mach-at91/Makefile
@@ -46,7 +46,6 @@ obj-$(CONFIG_MACH_ECBAT91) += board-ecbat91.o
obj-$(CONFIG_MACH_YL9200) += board-yl-9200.o
obj-$(CONFIG_MACH_CPUAT91) += board-cpuat91.o
obj-$(CONFIG_MACH_ECO920) += board-eco920.o
-obj-$(CONFIG_MACH_RSI_EWS) += board-rsi-ews.o
# AT91SAM9260 board-specific support
obj-$(CONFIG_MACH_AT91SAM9260EK) += board-sam9260ek.o
diff --git a/arch/arm/mach-at91/board-rsi-ews.c b/arch/arm/mach-at91/board-rsi-ews.c
deleted file mode 100644
index f28e8b7..0000000
--- a/arch/arm/mach-at91/board-rsi-ews.c
+++ /dev/null
@@ -1,232 +0,0 @@
-/*
- * board-rsi-ews.c
- *
- * Copyright (C)
- * 2005 SAN People,
- * 2008-2011 R-S-I Elektrotechnik GmbH & Co. KG
- *
- * Licensed under GPLv2 or later.
- */
-
-#include <linux/types.h>
-#include <linux/init.h>
-#include <linux/mm.h>
-#include <linux/module.h>
-#include <linux/platform_device.h>
-#include <linux/spi/spi.h>
-#include <linux/mtd/physmap.h>
-
-#include <asm/setup.h>
-#include <asm/mach-types.h>
-#include <asm/irq.h>
-
-#include <asm/mach/arch.h>
-#include <asm/mach/map.h>
-#include <asm/mach/irq.h>
-
-#include <mach/hardware.h>
-
-#include <linux/gpio.h>
-
-#include "at91_aic.h"
-#include "board.h"
-#include "generic.h"
-#include "gpio.h"
-
-static void __init rsi_ews_init_early(void)
-{
- /* Initialize processor: 18.432 MHz crystal */
- at91_initialize(18432000);
-}
-
-/*
- * Ethernet
- */
-static struct macb_platform_data rsi_ews_eth_data __initdata = {
- .phy_irq_pin = AT91_PIN_PC4,
- .is_rmii = 1,
-};
-
-/*
- * USB Host
- */
-static struct at91_usbh_data rsi_ews_usbh_data __initdata = {
- .ports = 1,
- .vbus_pin = {-EINVAL, -EINVAL},
- .overcurrent_pin= {-EINVAL, -EINVAL},
-};
-
-/*
- * SD/MC
- */
-static struct mci_platform_data __initdata rsi_ews_mci0_data = {
- .slot[0] = {
- .bus_width = 4,
- .detect_pin = AT91_PIN_PB27,
- .wp_pin = AT91_PIN_PB29,
- },
-};
-
-/*
- * I2C
- */
-static struct i2c_board_info rsi_ews_i2c_devices[] __initdata = {
- {
- I2C_BOARD_INFO("ds1337", 0x68),
- },
- {
- I2C_BOARD_INFO("24c01", 0x50),
- }
-};
-
-/*
- * LEDs
- */
-static struct gpio_led rsi_ews_leds[] = {
- {
- .name = "led0",
- .gpio = AT91_PIN_PB6,
- .active_low = 0,
- },
- {
- .name = "led1",
- .gpio = AT91_PIN_PB7,
- .active_low = 0,
- },
- {
- .name = "led2",
- .gpio = AT91_PIN_PB8,
- .active_low = 0,
- },
- {
- .name = "led3",
- .gpio = AT91_PIN_PB9,
- .active_low = 0,
- },
-};
-
-/*
- * DataFlash
- */
-static struct spi_board_info rsi_ews_spi_devices[] = {
- { /* DataFlash chip 1*/
- .modalias = "mtd_dataflash",
- .chip_select = 0,
- .max_speed_hz = 5 * 1000 * 1000,
- },
- { /* DataFlash chip 2*/
- .modalias = "mtd_dataflash",
- .chip_select = 1,
- .max_speed_hz = 5 * 1000 * 1000,
- },
-};
-
-/*
- * NOR flash
- */
-static struct mtd_partition rsiews_nor_partitions[] = {
- {
- .name = "boot",
- .offset = 0,
- .size = 3 * SZ_128K,
- .mask_flags = MTD_WRITEABLE
- },
- {
- .name = "kernel",
- .offset = MTDPART_OFS_NXTBLK,
- .size = SZ_2M - (3 * SZ_128K)
- },
- {
- .name = "root",
- .offset = MTDPART_OFS_NXTBLK,
- .size = SZ_8M
- },
- {
- .name = "kernelupd",
- .offset = MTDPART_OFS_NXTBLK,
- .size = 3 * SZ_512K,
- .mask_flags = MTD_WRITEABLE
- },
- {
- .name = "rootupd",
- .offset = MTDPART_OFS_NXTBLK,
- .size = 9 * SZ_512K,
- .mask_flags = MTD_WRITEABLE
- },
-};
-
-static struct physmap_flash_data rsiews_nor_data = {
- .width = 2,
- .parts = rsiews_nor_partitions,
- .nr_parts = ARRAY_SIZE(rsiews_nor_partitions),
-};
-
-#define NOR_BASE AT91_CHIPSELECT_0
-#define NOR_SIZE SZ_16M
-
-static struct resource nor_flash_resources[] = {
- {
- .start = NOR_BASE,
- .end = NOR_BASE + NOR_SIZE - 1,
- .flags = IORESOURCE_MEM,
- }
-};
-
-static struct platform_device rsiews_nor_flash = {
- .name = "physmap-flash",
- .id = 0,
- .dev = {
- .platform_data = &rsiews_nor_data,
- },
- .resource = nor_flash_resources,
- .num_resources = ARRAY_SIZE(nor_flash_resources),
-};
-
-/*
- * Init Func
- */
-static void __init rsi_ews_board_init(void)
-{
- /* Serial */
- /* DBGU on ttyS0. (Rx & Tx only) */
- /* This one is for debugging */
- at91_register_uart(0, 0, 0);
-
- /* USART1 on ttyS2. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */
- /* Dialin/-out modem interface */
- at91_register_uart(AT91RM9200_ID_US1, 2, ATMEL_UART_CTS | ATMEL_UART_RTS
- | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD
- | ATMEL_UART_RI);
-
- /* USART3 on ttyS4. (Rx, Tx, RTS) */
- /* RS485 communication */
- at91_register_uart(AT91RM9200_ID_US3, 4, ATMEL_UART_RTS);
- at91_add_device_serial();
- at91_set_gpio_output(AT91_PIN_PA21, 0);
- /* Ethernet */
- at91_add_device_eth(&rsi_ews_eth_data);
- /* USB Host */
- at91_add_device_usbh(&rsi_ews_usbh_data);
- /* I2C */
- at91_add_device_i2c(rsi_ews_i2c_devices,
- ARRAY_SIZE(rsi_ews_i2c_devices));
- /* SPI */
- at91_add_device_spi(rsi_ews_spi_devices,
- ARRAY_SIZE(rsi_ews_spi_devices));
- /* MMC */
- at91_add_device_mci(0, &rsi_ews_mci0_data);
- /* NOR Flash */
- platform_device_register(&rsiews_nor_flash);
- /* LEDs */
- at91_gpio_leds(rsi_ews_leds, ARRAY_SIZE(rsi_ews_leds));
-}
-
-MACHINE_START(RSI_EWS, "RSI EWS")
- /* Maintainer: Josef Holzmayr <holzmayr at rsi-elektrotechnik.de> */
- .init_time = at91rm9200_timer_init,
- .map_io = at91_map_io,
- .handle_irq = at91_aic_handle_irq,
- .init_early = rsi_ews_init_early,
- .init_irq = at91_init_irq_default,
- .init_machine = rsi_ews_board_init,
-MACHINE_END
--
2.1.0
--
_____________________________________________________________
R-S-I Elektrotechnik GmbH & Co. KG
Woelkestrasse 11
D-85301 Schweitenkirchen
Fon: +49 8444 9204-0
Fax: +49 8444 9204-50
www.rsi-elektrotechnik.de
_____________________________________________________________
Amtsgericht Ingolstadt - GmbH: HRB 191328 - KG: HRA 170363
Geschäftsführer: Dr.-Ing. Michael Sorg, Dipl.-Ing. Franz Sorg
USt-IdNr.: DE 128592548
More information about the linux-arm-kernel
mailing list