[PATCH V2 1/3] mmc: dw_mmc: use mmc_regulator_get_supply to handle regulators
Bartlomiej Zolnierkiewicz
b.zolnierkie at samsung.com
Wed Oct 1 06:57:54 PDT 2014
Hi,
On Tuesday, September 30, 2014 02:23:44 PM Jaehoon Chung wrote:
> Hi
>
> On 09/29/2014 09:31 PM, Bartlomiej Zolnierkiewicz wrote:
> >
> > Hi,
> >
> > On Friday, August 29, 2014 01:34:44 PM Ulf Hansson wrote:
> >> On 22 August 2014 15:47, Yuvaraj Kumar C D <yuvaraj.cd at gmail.com> wrote:
> >>> This patch makes use of mmc_regulator_get_supply() to handle
> >>> the vmmc and vqmmc regulators.Also it moves the code handling
> >>> the these regulators to dw_mci_set_ios().It turned on the vmmc
> >>> and vqmmc during MMC_POWER_UP and MMC_POWER_ON,and turned off
> >>> during MMC_POWER_OFF.
> >>>
> >>> Signed-off-by: Yuvaraj Kumar C D <yuvaraj.cd at samsung.com>
> >>
> >> Thanks! Applied for next.
> >
> > Unfortunately this patch breaks mmc1 card (Kingston 32GB micro SDHC)
> > detection on Exynos5420 Arndale Octa for me:
> >
> > [ 10.797979] dwmmc_exynos 12220000.mmc: no support for card's volts
> > [ 10.797998] mmc1: error -22 whilst initialising SD card
>
> OCR value is not matched. Which values are supported about the mmc_host's value and card's value?
> Could you share the value?
Sure. I've added dev_info()s at the beginning of mmc_select_voltage():
+ dev_warn(mmc_dev(host), "card's volts: 0x%0x\n", ocr);
+ dev_warn(mmc_dev(host), "host's volts: 0x%0x\n", host->ocr_avail);
and got following results:
[ 10.851678] dwmmc_exynos 12220000.mmc: card's volts: 0xff8000
[ 10.851691] dwmmc_exynos 12220000.mmc: host's volts: 0x80
Best regards,
--
Bartlomiej Zolnierkiewicz
Samsung R&D Institute Poland
Samsung Electronics
> Best Regards,
> Jaehoon Chung
>
> >
> > Without the patch:
> >
> > [ 10.866926] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 50000000Hz, actual 50000000HZ div = 0)
> > [ 10.866977] mmc1: new high speed SDHC card at address 1234
> > [ 10.868730] mmcblk1: mmc1:1234 SA32G 29.3 GiB
> > [ 10.915054] mmcblk1: p1 p2 p3
> >
> > The config is attached (exynos_defconfig doesn't work correctly for
> > this board yet).
> >
> > Best regards,
> > --
> > Bartlomiej Zolnierkiewicz
> > Samsung R&D Institute Poland
> > Samsung Electronics
> >
> >> Kind regards
> >> Uffe
> >>
> >>> ---
> >>> changes from v1:
> >>> 1.Used mmc_regulator_set_ocr() instead of regulator_enable() for vmmc.
> >>> 2.Turned on vmmc and vqmmc during MMC_POWER_UP.
> >>> 3. Removed the flags DW_MMC_CARD_POWERED and DW_MMC_IO_POWERED which
> >>> added during the initial version of this patch.
> >>> 4. Added error message, if it failed to turn on regulator's.
> >>>
> >>> drivers/mmc/host/dw_mmc.c | 72 +++++++++++++++++++++-----------------------
> >>> include/linux/mmc/dw_mmc.h | 2 +-
> >>> 2 files changed, 36 insertions(+), 38 deletions(-)
> >>>
> >>> diff --git a/drivers/mmc/host/dw_mmc.c b/drivers/mmc/host/dw_mmc.c
> >>> index 7f227e9..aadb0d6 100644
> >>> --- a/drivers/mmc/host/dw_mmc.c
> >>> +++ b/drivers/mmc/host/dw_mmc.c
> >>> @@ -936,6 +936,7 @@ static void dw_mci_set_ios(struct mmc_host *mmc, struct mmc_ios *ios)
> >>> struct dw_mci_slot *slot = mmc_priv(mmc);
> >>> const struct dw_mci_drv_data *drv_data = slot->host->drv_data;
> >>> u32 regs;
> >>> + int ret;
> >>>
> >>> switch (ios->bus_width) {
> >>> case MMC_BUS_WIDTH_4:
> >>> @@ -974,12 +975,38 @@ static void dw_mci_set_ios(struct mmc_host *mmc, struct mmc_ios *ios)
> >>>
> >>> switch (ios->power_mode) {
> >>> case MMC_POWER_UP:
> >>> + if (!IS_ERR(mmc->supply.vmmc)) {
> >>> + ret = mmc_regulator_set_ocr(mmc, mmc->supply.vmmc,
> >>> + ios->vdd);
> >>> + if (ret) {
> >>> + dev_err(slot->host->dev,
> >>> + "failed to enable vmmc regulator\n");
> >>> + /*return, if failed turn on vmmc*/
> >>> + return;
> >>> + }
> >>> + }
> >>> + if (!IS_ERR(mmc->supply.vqmmc) && !slot->host->vqmmc_enabled) {
> >>> + ret = regulator_enable(mmc->supply.vqmmc);
> >>> + if (ret < 0)
> >>> + dev_err(slot->host->dev,
> >>> + "failed to enable vqmmc regulator\n");
> >>> + else
> >>> + slot->host->vqmmc_enabled = true;
> >>> + }
> >>> set_bit(DW_MMC_CARD_NEED_INIT, &slot->flags);
> >>> regs = mci_readl(slot->host, PWREN);
> >>> regs |= (1 << slot->id);
> >>> mci_writel(slot->host, PWREN, regs);
> >>> break;
> >>> case MMC_POWER_OFF:
> >>> + if (!IS_ERR(mmc->supply.vmmc))
> >>> + mmc_regulator_set_ocr(mmc, mmc->supply.vmmc, 0);
> >>> +
> >>> + if (!IS_ERR(mmc->supply.vqmmc) && slot->host->vqmmc_enabled) {
> >>> + regulator_disable(mmc->supply.vqmmc);
> >>> + slot->host->vqmmc_enabled = false;
> >>> + }
> >>> +
> >>> regs = mci_readl(slot->host, PWREN);
> >>> regs &= ~(1 << slot->id);
> >>> mci_writel(slot->host, PWREN, regs);
> >>> @@ -2110,7 +2137,13 @@ static int dw_mci_init_slot(struct dw_mci *host, unsigned int id)
> >>> mmc->f_max = freq[1];
> >>> }
> >>>
> >>> - mmc->ocr_avail = MMC_VDD_32_33 | MMC_VDD_33_34;
> >>> + /*if there are external regulators, get them*/
> >>> + ret = mmc_regulator_get_supply(mmc);
> >>> + if (ret == -EPROBE_DEFER)
> >>> + goto err_setup_bus;
> >>> +
> >>> + if (!mmc->ocr_avail)
> >>> + mmc->ocr_avail = MMC_VDD_32_33 | MMC_VDD_33_34;
> >>>
> >>> if (host->pdata->caps)
> >>> mmc->caps = host->pdata->caps;
> >>> @@ -2176,7 +2209,7 @@ static int dw_mci_init_slot(struct dw_mci *host, unsigned int id)
> >>>
> >>> err_setup_bus:
> >>> mmc_free_host(mmc);
> >>> - return -EINVAL;
> >>> + return ret;
> >>> }
> >>>
> >>> static void dw_mci_cleanup_slot(struct dw_mci_slot *slot, unsigned int id)
> >>> @@ -2469,24 +2502,6 @@ int dw_mci_probe(struct dw_mci *host)
> >>> }
> >>> }
> >>>
> >>> - host->vmmc = devm_regulator_get_optional(host->dev, "vmmc");
> >>> - if (IS_ERR(host->vmmc)) {
> >>> - ret = PTR_ERR(host->vmmc);
> >>> - if (ret == -EPROBE_DEFER)
> >>> - goto err_clk_ciu;
> >>> -
> >>> - dev_info(host->dev, "no vmmc regulator found: %d\n", ret);
> >>> - host->vmmc = NULL;
> >>> - } else {
> >>> - ret = regulator_enable(host->vmmc);
> >>> - if (ret) {
> >>> - if (ret != -EPROBE_DEFER)
> >>> - dev_err(host->dev,
> >>> - "regulator_enable fail: %d\n", ret);
> >>> - goto err_clk_ciu;
> >>> - }
> >>> - }
> >>> -
> >>> host->quirks = host->pdata->quirks;
> >>>
> >>> spin_lock_init(&host->lock);
> >>> @@ -2630,8 +2645,6 @@ err_workqueue:
> >>> err_dmaunmap:
> >>> if (host->use_dma && host->dma_ops->exit)
> >>> host->dma_ops->exit(host);
> >>> - if (host->vmmc)
> >>> - regulator_disable(host->vmmc);
> >>>
> >>> err_clk_ciu:
> >>> if (!IS_ERR(host->ciu_clk))
> >>> @@ -2667,9 +2680,6 @@ void dw_mci_remove(struct dw_mci *host)
> >>> if (host->use_dma && host->dma_ops->exit)
> >>> host->dma_ops->exit(host);
> >>>
> >>> - if (host->vmmc)
> >>> - regulator_disable(host->vmmc);
> >>> -
> >>> if (!IS_ERR(host->ciu_clk))
> >>> clk_disable_unprepare(host->ciu_clk);
> >>>
> >>> @@ -2686,9 +2696,6 @@ EXPORT_SYMBOL(dw_mci_remove);
> >>> */
> >>> int dw_mci_suspend(struct dw_mci *host)
> >>> {
> >>> - if (host->vmmc)
> >>> - regulator_disable(host->vmmc);
> >>> -
> >>> return 0;
> >>> }
> >>> EXPORT_SYMBOL(dw_mci_suspend);
> >>> @@ -2697,15 +2704,6 @@ int dw_mci_resume(struct dw_mci *host)
> >>> {
> >>> int i, ret;
> >>>
> >>> - if (host->vmmc) {
> >>> - ret = regulator_enable(host->vmmc);
> >>> - if (ret) {
> >>> - dev_err(host->dev,
> >>> - "failed to enable regulator: %d\n", ret);
> >>> - return ret;
> >>> - }
> >>> - }
> >>> -
> >>> if (!dw_mci_ctrl_reset(host, SDMMC_CTRL_ALL_RESET_FLAGS)) {
> >>> ret = -ENODEV;
> >>> return ret;
> >>> diff --git a/include/linux/mmc/dw_mmc.h b/include/linux/mmc/dw_mmc.h
> >>> index 29ce014..84e2827 100644
> >>> --- a/include/linux/mmc/dw_mmc.h
> >>> +++ b/include/linux/mmc/dw_mmc.h
> >>> @@ -188,7 +188,7 @@ struct dw_mci {
> >>> /* Workaround flags */
> >>> u32 quirks;
> >>>
> >>> - struct regulator *vmmc; /* Power regulator */
> >>> + bool vqmmc_enabled;
> >>> unsigned long irq_flags; /* IRQ flags */
> >>> int irq;
> >>> };
> >>> --
> >>> 1.7.10.4
More information about the linux-arm-kernel
mailing list