[PATCH 05/17] pci: host: pcie-dra7xx: add support for pcie-dra7xx controller

Jason Gunthorpe jgunthorpe at obsidianresearch.com
Tue May 6 09:35:08 PDT 2014


On Tue, May 06, 2014 at 07:03:51PM +0530, Kishon Vijay Abraham I wrote:
> +Example:
> +pcie at 51000000 {
> +	compatible = "ti,dra7xx-pcie";
> +	reg = <0x51002000 0x14c>, <0x51000000 0x2000>;
> +	reg-names = "ti_conf", "rc_dbics";
> +	interrupts = <0 232 0x4>, <0 233 0x4>;
> +	#address-cells = <3>;
> +	#size-cells = <2>;
> +	device_type = "pci";
> +	ti,device_type = <3>;
> +	ranges = <0x00000800 0 0x20001000 0x20001000 0 0x00002000  /* Configuration Space */

Configuration space should not show up in the ranges, please don't
copy that mistake from other drivers, put it in reg.

> +	interrupt-map-mask = <0 0 0 0>;
> +	interrupt-map = <0x0 0 &gic 134>;

The HW cannot decode INTA/B/C/D?

> +#define	PCIECTRL_DRA7XX_CONF_IRQSTATUS_MSI		0x0034
> +#define	PCIECTRL_DRA7XX_CONF_IRQENABLE_SET_MSI		0x0038
> +#define	INTA						BIT(0)
> +#define	INTB						BIT(1)
> +#define	INTC						BIT(2)
> +#define	INTD						BIT(3)
> +#define	MSI						BIT(4)
> +#define	LEG_EP_INTERRUPTS (INTA | INTB | INTC | INTD)

Oh, it can, it would be wise to export this from the driver. Look at
the latest patches from Srikanth Thokala for the Xilinx PCI driver to
see how this should look

> +static int dra7xx_pcie_establish_link(struct pcie_port *pp)
> +{
> +	u32 reg;
> +	int retries = 1000;
> +	struct dra7xx_pcie *dra7xx = to_dra7xx_pcie(pp);
> +
> +	if (dw_pcie_link_up(pp)) {
> +		dev_err(pp->dev, "link is already up\n");
> +		return 0;
> +	}
> +
> +	reg = dra7xx_pcie_readl(dra7xx->base, PCIECTRL_DRA7XX_CONF_DEVICE_CMD);
> +	reg |= LTSSM_EN;
> +	dra7xx_pcie_writel(dra7xx->base, PCIECTRL_DRA7XX_CONF_DEVICE_CMD, reg);
> +
> +	while (--retries) {
> +		reg = dra7xx_pcie_readl(dra7xx->base,
> +					PCIECTRL_DRA7XX_CONF_PHY_CS);
> +		if (reg & LINK_UP)
> +			break;
> +		usleep_range(10, 20);
> +	}
> +
> +	if (retries <= 0) {
> +		dev_err(pp->dev, "link is not up\n");
> +		return -ETIMEDOUT;
> +	}
> +
> +	return 0;
> +}

It would be really nice to see the link bring up process live in the
PCI core, every driver seems to have its own take on this.

The PCI-E spec requires a 100ms delay after link bring up (aka hot
reset) before sending any configuration TLPs.

Jason



More information about the linux-arm-kernel mailing list