mainline boot: 64 boots: 62 pass, 2 fail (v3.16-rc1-2-gebe0618)

Laura Abbott lauraa at codeaurora.org
Tue Jun 24 10:47:11 PDT 2014


On 6/23/2014 11:32 AM, Kevin Hilman wrote:
> On Sun, Jun 22, 2014 at 8:56 PM, Tushar Behera <trblinux at gmail.com> wrote:
>> Adding linux-samsung-soc and linux-arm-kernel ML for wider audience.
>>
>> On 06/19/2014 04:12 PM, Tushar Behera wrote:
>>> On 06/19/2014 03:02 PM, Tushar Behera wrote:
>>>> On 06/18/2014 09:22 AM, Kevin Hilman wrote:
>>>>> On Tue, Jun 17, 2014 at 8:26 PM, Tushar Behera <trblinux at gmail.com> wrote:
>>>>>> On 06/17/2014 10:23 PM, Kevin Hilman wrote:
>>>>>>> Sachin,
>>>>>>>
>>>>>>> On Mon, Jun 16, 2014 at 11:16 PM, Kevin's boot bot <khilman at linaro.org> wrote:
>>>>>>>>
>>>>>>>> Tree/Branch: mainline
>>>>>>>> Git describe: v3.16-rc1-2-gebe0618
>>>>>>>> Failed boot tests (console logs at the end)
>>>>>>>> ===========================================
>>>>>>>>      exynos5420-arndale-octa:     FAIL:    arm-exynos_defconfig
>>>>>>>>                 ste-snowball:     FAIL:    arm-u8500_defconfig
>>>>>>>
>>>>>>> FYI... these failures are getting more consistent on my octa board,
>>>>>>> but still not failing every time.
>>>>>>>
>>>>>>> Kevin
>>>>>>>
>>>>>>
>>>>>> Hi Kevin,
>>>>>>
>>>>>> Same here.
>>>>>>
>>>>>> Observation: If you soft-reset the board (through the jumpers) after
>>>>>> getting this problem, the problem keeps repeating. But if you hard-reset
>>>>>> the board (by removing the power cord), the problem doesn't occur during
>>>>>> next iteration.
>>>>>
>>>>> I don't ever use the soft-reset, I only toggle the wall power.  I
>>>>> don't ever actually remove the power cord though, I'm using a
>>>>> USB-controlled relay to toggle the wall power.
>>>>>
>>>>> Kevin
>>>>>
>>>>
>>>> Laura,
>>>>
>>>> We are getting following kernel panic [1] (not always, but quite
>>>> regularly) while booting Arndale-Octa (based on Samsung's Exynos5420)
>>>> board with upstream kernel. I haven't observed this issue with other
>>>> boards yet.
>>>>
>>>> This issue is observed when I am booting with uImage + dtb (within
>>>> roughly ~10 iterations).
>>>>
>>>
>>> Some more information:
>>>
>>> The boot logs are provided in pastebin, okay[2] and failed[3].
>>>
>>> In case of boot failures, I am getting a higher value for vm_total_pages
>>> (684424 in [3]). In case of successful boot on my board, it is always
>>> 521232 [2] on my board.
> 
> I can confirm that reverting the "Get rid of meminfo" patch gets the
> Octa board booting reliably again for me also.
> 
> In case it helps, some boot logs for failures from the last copule
> linux-next build/boot cycles can be seen here:
> http://armcloud.us/kernel-ci/next/next-20140623/arm-exynos_defconfig/boot-exynos5420-arndale-octa.log
> http://armcloud.us/kernel-ci/next/next-20140620/arm-exynos_defconfig/boot-exynos5420-arndale-octa.log
> 

Sorry, I missed this yesterday. I'm going to take a look.

Thanks,
Laura

-- 
Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum,
hosted by The Linux Foundation



More information about the linux-arm-kernel mailing list