[PATCH 1/4] phy: Add provision for calibrating phy.

Vivek Gautam gautam.vivek at samsung.com
Fri Jun 6 05:12:12 PDT 2014


Some PHY controllers may need to calibrate certain
PHY settings after initialization of the controller and
sometimes even after initializing the PHY-consumer too.
Add support for the same in order to let consumers do so in need.

Signed-off-by: vivek Gautam <gautam.vivek at samsung.com>
---
 drivers/phy/phy-core.c  |   36 ++++++++++++++++++++++++++++++++++++
 include/linux/phy/phy.h |    7 +++++++
 2 files changed, 43 insertions(+)

diff --git a/drivers/phy/phy-core.c b/drivers/phy/phy-core.c
index 74d4346..92d31a3 100644
--- a/drivers/phy/phy-core.c
+++ b/drivers/phy/phy-core.c
@@ -376,6 +376,42 @@ int phy_power_off(struct phy *phy)
 EXPORT_SYMBOL_GPL(phy_power_off);
 
 /**
+ * phy_calibrate - calibrate a phy post initialization
+ * @phy: Pointer to 'phy' from consumer
+ *
+ * For certain PHYs, it may be needed to calibrate few phy parameters
+ * post initialization. The need to calibrate may arise after the
+ * initialization of consumer itself, in order to prevent further any
+ * loss of phy settings post consumer-initialization.
+ *	example: USB 3.0 DRD PHY on Exynos5420/5800 systems is one such
+ *	phy which needs calibration after the host controller reset
+ *	has happened.
+ */
+int phy_calibrate(struct phy *phy)
+{
+	int ret = -ENOTSUPP;
+
+	if (!phy)
+		return 0;
+
+	mutex_lock(&phy->mutex);
+	if (phy->ops->calibrate) {
+		ret =  phy->ops->calibrate(phy);
+		if (ret < 0) {
+			dev_err(&phy->dev,
+				"phy calibration failed --> %d\n", ret);
+			goto out;
+		}
+	}
+
+out:
+	mutex_unlock(&phy->mutex);
+
+	return ret;
+}
+EXPORT_SYMBOL_GPL(phy_calibrate);
+
+/**
  * _of_phy_get() - lookup and obtain a reference to a phy by phandle
  * @np: device_node for which to get the phy
  * @index: the index of the phy
diff --git a/include/linux/phy/phy.h b/include/linux/phy/phy.h
index 5a537a5..1de6c0a 100644
--- a/include/linux/phy/phy.h
+++ b/include/linux/phy/phy.h
@@ -34,6 +34,7 @@ struct phy_ops {
 	int	(*exit)(struct phy *phy);
 	int	(*power_on)(struct phy *phy);
 	int	(*power_off)(struct phy *phy);
+	int	(*calibrate)(struct phy *phy);
 	struct module *owner;
 };
 
@@ -124,6 +125,7 @@ int phy_init(struct phy *phy);
 int phy_exit(struct phy *phy);
 int phy_power_on(struct phy *phy);
 int phy_power_off(struct phy *phy);
+int phy_calibrate(struct phy *phy);
 static inline int phy_get_bus_width(struct phy *phy)
 {
 	return phy->attrs.bus_width;
@@ -227,6 +229,11 @@ static inline int phy_power_off(struct phy *phy)
 	return -ENOSYS;
 }
 
+static inline int phy_calibrate(struct phy *phy)
+{
+	return -ENOSYS;
+}
+
 static inline int phy_get_bus_width(struct phy *phy)
 {
 	return -ENOSYS;
-- 
1.7.10.4




More information about the linux-arm-kernel mailing list