[PATCH v3 2/2] can: m_can: add Bosch M_CAN controller support

[Varka Bhadram]

On 07/14/2014 01:54 PM, Dong Aisheng wrote:
> On Mon, Jul 14, 2014 at 01:05:55PM +0530, Varka Bhadram wrote:
>> On 07/14/2014 12:51 PM, Dong Aisheng wrote:
>>> +    dev_dbg(&pdev->dev, "mram_base %p sidf 0x%x %d xidf 0x%x %d rxf0
>>> 0x%x %d rxf1 0x%x %d rxb 0x%x %d txe 0x%x %d txb 0x%x %d\n",
>>> +        priv->mram_base,
>>> +        priv->mcfg[MRAM_SIDF].off, priv->mcfg[MRAM_SIDF].num,
>>> +        priv->mcfg[MRAM_XIDF].off, priv->mcfg[MRAM_XIDF].num,
>>> +        priv->mcfg[MRAM_RXF0].off, priv->mcfg[MRAM_RXF0].num,
>>> +        priv->mcfg[MRAM_RXF1].off, priv->mcfg[MRAM_RXF1].num,
>>> +        priv->mcfg[MRAM_RXB].off, priv->mcfg[MRAM_RXB].num,
>>> +        priv->mcfg[MRAM_TXE].off, priv->mcfg[MRAM_TXE].num,
>>> +        priv->mcfg[MRAM_TXB].off, priv->mcfg[MRAM_TXB].num);
>>> +
>>>>>> dev_dbg() will insert the new lines in b/w. It wont print the values as
>>>>>> you expected.
>>>>>> Check this by enabling debug ...
>>>>> What do you mean by b/w?
>>>> You are expecting the data to be print in format like:
>>>> pdev->dev/name: mram_base %p sidf 0x%x %d xidf 0x%x %d rxf0 0x%x %d rxf1 0x%x %d rxb 0x%x %d txe 0x%x %d txb 0x%x %d
>>>>
>>>> But when we use the dev_dbg()/pr_debug()... It will put data like:
>>>> pdev->dev/name: mram_base %p sidf 0x%x
>>>> 0x%x %d rxf0 0x%x
>>>> rxf1 0x%x %d rxb
>>>> ....
>>>>
>>>> check this by enable DEBUG...
>>>>
>>> My test showed the format is:
>>> root at imx6qdlsolo:~# uname -a
>>> Linux imx6qdlsolo 3.16.0-rc2-next-20140627-00006-gd55dd62-dirty #373 SMP Fri Jul 11 18:12:31 CST 2014 armv7l GNU/Linux
>>> root at imx6qdlsolo:~# dmesg | grep m_can
>>> m_can 20e8000.can: mram_base c0990000 sidf 0x0 0 xidf 0x0 0 rxf0 0x0 32 rxf1 0x200 0 rxb 0x200 0 txe 0x200 0 txb 0x200 1
>>> m_can 20e8000.can: m_can device registered (regs=c0988000, irq=146)
>>> m_can 20f0000.can: mram_base c09a0000 sidf 0x400 0 xidf 0x400 0 rxf0 0x400 32 rxf1 0x600 0 rxb 0x600 0 txe 0x600 0 txb 0x600 1
>>> m_can 20f0000.can: m_can device registered (regs=c0998000, irq=147)
>>>
>> I think you got the expected result.
>>
>> I faced the above problem when i use pr_debug(). Can you check with this....?
>>
> It works too.
> root at imx6qdlsolo:~# dmesg | grep mram
> mram_base c0990000 sidf 0x0 0 xidf 0x0 0 rxf0 0x0 32 rxf1 0x200 0 rxb 0x200 0 txe 0x200 0 txb 0x200 1
> mram_base c09a0000 sidf 0x400 0 xidf 0x400 0 rxf0 0x400 32 rxf1 0x600 0 rxb 0x600 0 txe 0x600 0 txb 0x600 1
>
Ohooooo... I got the problem because i used pr_debug in a 'for' loop.

Any way thanks.

>> This is good. Thanks for clarification.
>>
>>> Regards
>>> Dong Aisheng
>>>
>> -- 
>> Regards,
>> Varka Bhadram.
>>
> Regards
> Dong Aisheng


-- 
Regards,
Varka Bhadram.