[PATCH v3 2/2] can: m_can: add Bosch M_CAN controller support

[Dong Aisheng]

On Mon, Jul 14, 2014 at 01:05:55PM +0530, Varka Bhadram wrote:
> On 07/14/2014 12:51 PM, Dong Aisheng wrote:
> >
> >+    dev_dbg(&pdev->dev, "mram_base %p sidf 0x%x %d xidf 0x%x %d rxf0
> >0x%x %d rxf1 0x%x %d rxb 0x%x %d txe 0x%x %d txb 0x%x %d\n",
> >+        priv->mram_base,
> >+        priv->mcfg[MRAM_SIDF].off, priv->mcfg[MRAM_SIDF].num,
> >+        priv->mcfg[MRAM_XIDF].off, priv->mcfg[MRAM_XIDF].num,
> >+        priv->mcfg[MRAM_RXF0].off, priv->mcfg[MRAM_RXF0].num,
> >+        priv->mcfg[MRAM_RXF1].off, priv->mcfg[MRAM_RXF1].num,
> >+        priv->mcfg[MRAM_RXB].off, priv->mcfg[MRAM_RXB].num,
> >+        priv->mcfg[MRAM_TXE].off, priv->mcfg[MRAM_TXE].num,
> >+        priv->mcfg[MRAM_TXB].off, priv->mcfg[MRAM_TXB].num);
> >+
> >>>>dev_dbg() will insert the new lines in b/w. It wont print the values as
> >>>>you expected.
> >>>>Check this by enabling debug ...
> >>>What do you mean by b/w?
> >>You are expecting the data to be print in format like:
> >>pdev->dev/name: mram_base %p sidf 0x%x %d xidf 0x%x %d rxf0 0x%x %d rxf1 0x%x %d rxb 0x%x %d txe 0x%x %d txb 0x%x %d
> >>
> >>But when we use the dev_dbg()/pr_debug()... It will put data like:
> >>pdev->dev/name: mram_base %p sidf 0x%x
> >>0x%x %d rxf0 0x%x
> >>rxf1 0x%x %d rxb
> >>....
> >>
> >>check this by enable DEBUG...
> >>
> >My test showed the format is:
> >root at imx6qdlsolo:~# uname -a
> >Linux imx6qdlsolo 3.16.0-rc2-next-20140627-00006-gd55dd62-dirty #373 SMP Fri Jul 11 18:12:31 CST 2014 armv7l GNU/Linux
> >root at imx6qdlsolo:~# dmesg | grep m_can
> >m_can 20e8000.can: mram_base c0990000 sidf 0x0 0 xidf 0x0 0 rxf0 0x0 32 rxf1 0x200 0 rxb 0x200 0 txe 0x200 0 txb 0x200 1
> >m_can 20e8000.can: m_can device registered (regs=c0988000, irq=146)
> >m_can 20f0000.can: mram_base c09a0000 sidf 0x400 0 xidf 0x400 0 rxf0 0x400 32 rxf1 0x600 0 rxb 0x600 0 txe 0x600 0 txb 0x600 1
> >m_can 20f0000.can: m_can device registered (regs=c0998000, irq=147)
> >
> I think you got the expected result.
> 
> I faced the above problem when i use pr_debug(). Can you check with this....?
> 

It works too.
root at imx6qdlsolo:~# dmesg | grep mram 
mram_base c0990000 sidf 0x0 0 xidf 0x0 0 rxf0 0x0 32 rxf1 0x200 0 rxb 0x200 0 txe 0x200 0 txb 0x200 1
mram_base c09a0000 sidf 0x400 0 xidf 0x400 0 rxf0 0x400 32 rxf1 0x600 0 rxb 0x600 0 txe 0x600 0 txb 0x600 1

> This is good. Thanks for clarification.
> 
> >
> >Regards
> >Dong Aisheng
> >
> -- 
> Regards,
> Varka Bhadram.
> 

Regards
Dong Aisheng