[PATCH v7 08/15] ahci-imx: Port to library-ised ahci_platform

Hans de Goede hdegoede at redhat.com
Sat Feb 22 10:53:37 EST 2014


This avoids the ugliness of creating a nested platform device from probe.

While moving it around anyways, move the mk6q phy init code from probe
to imx_sata_enable, as the phy needs to be re-initialized on resume too,
otherwise the drive won't be recognized after resume.

Tested on a wandboard i.mx6 quad.

Signed-off-by: Hans de Goede <hdegoede at redhat.com>
---
 .../devicetree/bindings/ata/ahci-platform.txt      |   9 +-
 drivers/ata/ahci_imx.c                             | 331 ++++++++-------------
 2 files changed, 134 insertions(+), 206 deletions(-)

diff --git a/Documentation/devicetree/bindings/ata/ahci-platform.txt b/Documentation/devicetree/bindings/ata/ahci-platform.txt
index 499bfed..d86e854 100644
--- a/Documentation/devicetree/bindings/ata/ahci-platform.txt
+++ b/Documentation/devicetree/bindings/ata/ahci-platform.txt
@@ -5,8 +5,9 @@ Each SATA controller should have its own node.
 
 Required properties:
 - compatible        : compatible list, one of "snps,spear-ahci",
-                      "snps,exynos5440-ahci", "ibm,476gtr-ahci", or
-                      "allwinner,sun4i-a10-ahci"
+                      "snps,exynos5440-ahci", "ibm,476gtr-ahci",
+                      "allwinner,sun4i-a10-ahci", "fsl,imx53-ahci" or
+                      "fsl,imx6q-ahci"
 - interrupts        : <interrupt mapping for SATA IRQ>
 - reg               : <registers mapping>
 
@@ -15,6 +16,10 @@ Optional properties:
 - clocks            : a list of phandle + clock specifier pairs
 - target-supply     : regulator for SATA target power
 
+"fsl,imx53-ahci", "fsl,imx6q-ahci" required properties:
+- clocks            : must contain the sata, sata_ref and ahb clocks
+- clock-names       : must contain "ahb" for the ahb clock
+
 Examples:
         sata at ffe08000 {
 		compatible = "snps,spear-ahci";
diff --git a/drivers/ata/ahci_imx.c b/drivers/ata/ahci_imx.c
index dd4d6f7..3cb5d69 100644
--- a/drivers/ata/ahci_imx.c
+++ b/drivers/ata/ahci_imx.c
@@ -42,13 +42,7 @@ enum ahci_imx_type {
 struct imx_ahci_priv {
 	struct platform_device *ahci_pdev;
 	enum ahci_imx_type type;
-
-	/* i.MX53 clock */
-	struct clk *sata_gate_clk;
-	/* Common clock */
-	struct clk *sata_ref_clk;
 	struct clk *ahb_clk;
-
 	struct regmap *gpr;
 	bool no_device;
 	bool first_time;
@@ -58,28 +52,52 @@ static int ahci_imx_hotplug;
 module_param_named(hotplug, ahci_imx_hotplug, int, 0644);
 MODULE_PARM_DESC(hotplug, "AHCI IMX hot-plug support (0=Don't support, 1=support)");
 
-static int imx_sata_clock_enable(struct device *dev)
+static void ahci_imx_host_stop(struct ata_host *host);
+
+static int imx_sata_enable(struct ahci_host_priv *hpriv)
 {
-	struct imx_ahci_priv *imxpriv = dev_get_drvdata(dev->parent);
+	struct imx_ahci_priv *imxpriv = hpriv->plat_data;
 	int ret;
 
-	if (imxpriv->type == AHCI_IMX53) {
-		ret = clk_prepare_enable(imxpriv->sata_gate_clk);
-		if (ret < 0) {
-			dev_err(dev, "prepare-enable sata_gate clock err:%d\n",
-				ret);
+	if (imxpriv->no_device)
+		return 0;
+
+	if (hpriv->target_pwr) {
+		ret = regulator_enable(hpriv->target_pwr);
+		if (ret)
 			return ret;
-		}
 	}
 
-	ret = clk_prepare_enable(imxpriv->sata_ref_clk);
-	if (ret < 0) {
-		dev_err(dev, "prepare-enable sata_ref clock err:%d\n",
-			ret);
-		goto clk_err;
-	}
+	ret = ahci_platform_enable_clks(hpriv);
+	if (ret < 0)
+		goto disable_regulator;
 
 	if (imxpriv->type == AHCI_IMX6Q) {
+		/*
+		 * set PHY Paremeters, two steps to configure the GPR13,
+		 * one write for rest of parameters, mask of first write
+		 * is 0x07ffffff, and the other one write for setting
+		 * the mpll_clk_en.
+		 */
+		regmap_update_bits(imxpriv->gpr, IOMUXC_GPR13,
+				   IMX6Q_GPR13_SATA_RX_EQ_VAL_MASK |
+				   IMX6Q_GPR13_SATA_RX_LOS_LVL_MASK |
+				   IMX6Q_GPR13_SATA_RX_DPLL_MODE_MASK |
+				   IMX6Q_GPR13_SATA_SPD_MODE_MASK |
+				   IMX6Q_GPR13_SATA_MPLL_SS_EN |
+				   IMX6Q_GPR13_SATA_TX_ATTEN_MASK |
+				   IMX6Q_GPR13_SATA_TX_BOOST_MASK |
+				   IMX6Q_GPR13_SATA_TX_LVL_MASK |
+				   IMX6Q_GPR13_SATA_MPLL_CLK_EN |
+				   IMX6Q_GPR13_SATA_TX_EDGE_RATE,
+				   IMX6Q_GPR13_SATA_RX_EQ_VAL_3_0_DB |
+				   IMX6Q_GPR13_SATA_RX_LOS_LVL_SATA2M |
+				   IMX6Q_GPR13_SATA_RX_DPLL_MODE_2P_4F |
+				   IMX6Q_GPR13_SATA_SPD_MODE_3P0G |
+				   IMX6Q_GPR13_SATA_MPLL_SS_EN |
+				   IMX6Q_GPR13_SATA_TX_ATTEN_9_16 |
+				   IMX6Q_GPR13_SATA_TX_BOOST_3_33_DB |
+				   IMX6Q_GPR13_SATA_TX_LVL_1_025_V);
 		regmap_update_bits(imxpriv->gpr, IOMUXC_GPR13,
 				   IMX6Q_GPR13_SATA_MPLL_CLK_EN,
 				   IMX6Q_GPR13_SATA_MPLL_CLK_EN);
@@ -89,15 +107,19 @@ static int imx_sata_clock_enable(struct device *dev)
 
 	return 0;
 
-clk_err:
-	if (imxpriv->type == AHCI_IMX53)
-		clk_disable_unprepare(imxpriv->sata_gate_clk);
+disable_regulator:
+	if (hpriv->target_pwr)
+		regulator_disable(hpriv->target_pwr);
+
 	return ret;
 }
 
-static void imx_sata_clock_disable(struct device *dev)
+static void imx_sata_disable(struct ahci_host_priv *hpriv)
 {
-	struct imx_ahci_priv *imxpriv = dev_get_drvdata(dev->parent);
+	struct imx_ahci_priv *imxpriv = hpriv->plat_data;
+
+	if (imxpriv->no_device)
+		return;
 
 	if (imxpriv->type == AHCI_IMX6Q) {
 		regmap_update_bits(imxpriv->gpr, IOMUXC_GPR13,
@@ -105,10 +127,10 @@ static void imx_sata_clock_disable(struct device *dev)
 				   !IMX6Q_GPR13_SATA_MPLL_CLK_EN);
 	}
 
-	clk_disable_unprepare(imxpriv->sata_ref_clk);
+	ahci_platform_disable_clks(hpriv);
 
-	if (imxpriv->type == AHCI_IMX53)
-		clk_disable_unprepare(imxpriv->sata_gate_clk);
+	if (hpriv->target_pwr)
+		regulator_disable(hpriv->target_pwr);
 }
 
 static void ahci_imx_error_handler(struct ata_port *ap)
@@ -118,7 +140,7 @@ static void ahci_imx_error_handler(struct ata_port *ap)
 	struct ata_host *host = dev_get_drvdata(ap->dev);
 	struct ahci_host_priv *hpriv = host->private_data;
 	void __iomem *mmio = hpriv->mmio;
-	struct imx_ahci_priv *imxpriv = dev_get_drvdata(ap->dev->parent);
+	struct imx_ahci_priv *imxpriv = hpriv->plat_data;
 
 	ahci_error_handler(ap);
 
@@ -136,7 +158,7 @@ static void ahci_imx_error_handler(struct ata_port *ap)
 	 */
 	reg_val = readl(mmio + PORT_PHY_CTL);
 	writel(reg_val | PORT_PHY_CTL_PDDQ_LOC, mmio + PORT_PHY_CTL);
-	imx_sata_clock_disable(ap->dev);
+	imx_sata_disable(hpriv);
 	imxpriv->no_device = true;
 }
 
@@ -144,7 +166,9 @@ static int ahci_imx_softreset(struct ata_link *link, unsigned int *class,
 		       unsigned long deadline)
 {
 	struct ata_port *ap = link->ap;
-	struct imx_ahci_priv *imxpriv = dev_get_drvdata(ap->dev->parent);
+	struct ata_host *host = dev_get_drvdata(ap->dev);
+	struct ahci_host_priv *hpriv = host->private_data;
+	struct imx_ahci_priv *imxpriv = hpriv->plat_data;
 	int ret = -EIO;
 
 	if (imxpriv->type == AHCI_IMX53)
@@ -156,7 +180,8 @@ static int ahci_imx_softreset(struct ata_link *link, unsigned int *class,
 }
 
 static struct ata_port_operations ahci_imx_ops = {
-	.inherits	= &ahci_platform_ops,
+	.inherits	= &ahci_ops,
+	.host_stop	= ahci_imx_host_stop,
 	.error_handler	= ahci_imx_error_handler,
 	.softreset	= ahci_imx_softreset,
 };
@@ -168,79 +193,6 @@ static const struct ata_port_info ahci_imx_port_info = {
 	.port_ops	= &ahci_imx_ops,
 };
 
-static int imx_sata_init(struct device *dev, void __iomem *mmio)
-{
-	int ret = 0;
-	unsigned int reg_val;
-	struct imx_ahci_priv *imxpriv = dev_get_drvdata(dev->parent);
-
-	ret = imx_sata_clock_enable(dev);
-	if (ret < 0)
-		return ret;
-
-	/*
-	 * Configure the HWINIT bits of the HOST_CAP and HOST_PORTS_IMPL,
-	 * and IP vendor specific register HOST_TIMER1MS.
-	 * Configure CAP_SSS (support stagered spin up).
-	 * Implement the port0.
-	 * Get the ahb clock rate, and configure the TIMER1MS register.
-	 */
-	reg_val = readl(mmio + HOST_CAP);
-	if (!(reg_val & HOST_CAP_SSS)) {
-		reg_val |= HOST_CAP_SSS;
-		writel(reg_val, mmio + HOST_CAP);
-	}
-	reg_val = readl(mmio + HOST_PORTS_IMPL);
-	if (!(reg_val & 0x1)) {
-		reg_val |= 0x1;
-		writel(reg_val, mmio + HOST_PORTS_IMPL);
-	}
-
-	reg_val = clk_get_rate(imxpriv->ahb_clk) / 1000;
-	writel(reg_val, mmio + HOST_TIMER1MS);
-
-	return 0;
-}
-
-static void imx_sata_exit(struct device *dev)
-{
-	imx_sata_clock_disable(dev);
-}
-
-static int imx_ahci_suspend(struct device *dev)
-{
-	struct imx_ahci_priv *imxpriv =  dev_get_drvdata(dev->parent);
-
-	/*
-	 * If no_device is set, The CLKs had been gated off in the
-	 * initialization so don't do it again here.
-	 */
-	if (!imxpriv->no_device)
-		imx_sata_clock_disable(dev);
-
-	return 0;
-}
-
-static int imx_ahci_resume(struct device *dev)
-{
-	struct imx_ahci_priv *imxpriv =  dev_get_drvdata(dev->parent);
-	int ret = 0;
-
-	if (!imxpriv->no_device)
-		ret = imx_sata_clock_enable(dev);
-
-	return ret;
-}
-
-static struct ahci_platform_data imx_sata_pdata = {
-	.init		= imx_sata_init,
-	.exit		= imx_sata_exit,
-	.ata_port_info	= &ahci_imx_port_info,
-	.suspend	= imx_ahci_suspend,
-	.resume		= imx_ahci_resume,
-
-};
-
 static const struct of_device_id imx_ahci_of_match[] = {
 	{ .compatible = "fsl,imx53-ahci", .data = (void *)AHCI_IMX53 },
 	{ .compatible = "fsl,imx6q-ahci", .data = (void *)AHCI_IMX6Q },
@@ -251,151 +203,122 @@ MODULE_DEVICE_TABLE(of, imx_ahci_of_match);
 static int imx_ahci_probe(struct platform_device *pdev)
 {
 	struct device *dev = &pdev->dev;
-	struct resource *mem, *irq, res[2];
 	const struct of_device_id *of_id;
-	enum ahci_imx_type type;
-	const struct ahci_platform_data *pdata = NULL;
+	struct ahci_host_priv *hpriv;
 	struct imx_ahci_priv *imxpriv;
-	struct device *ahci_dev;
-	struct platform_device *ahci_pdev;
+	unsigned int reg_val;
 	int ret;
 
 	of_id = of_match_device(imx_ahci_of_match, dev);
 	if (!of_id)
 		return -EINVAL;
 
-	type = (enum ahci_imx_type)of_id->data;
-	pdata = &imx_sata_pdata;
-
 	imxpriv = devm_kzalloc(dev, sizeof(*imxpriv), GFP_KERNEL);
-	if (!imxpriv) {
-		dev_err(dev, "can't alloc ahci_host_priv\n");
+	if (!imxpriv)
 		return -ENOMEM;
-	}
-
-	ahci_pdev = platform_device_alloc("ahci", -1);
-	if (!ahci_pdev)
-		return -ENODEV;
-
-	ahci_dev = &ahci_pdev->dev;
-	ahci_dev->parent = dev;
 
 	imxpriv->no_device = false;
 	imxpriv->first_time = true;
-	imxpriv->type = type;
-
+	imxpriv->type = (enum ahci_imx_type)of_id->data;
 	imxpriv->ahb_clk = devm_clk_get(dev, "ahb");
 	if (IS_ERR(imxpriv->ahb_clk)) {
 		dev_err(dev, "can't get ahb clock.\n");
-		ret = PTR_ERR(imxpriv->ahb_clk);
-		goto err_out;
+		return PTR_ERR(imxpriv->ahb_clk);
 	}
 
-	if (type == AHCI_IMX53) {
-		imxpriv->sata_gate_clk = devm_clk_get(dev, "sata_gate");
-		if (IS_ERR(imxpriv->sata_gate_clk)) {
-			dev_err(dev, "can't get sata_gate clock.\n");
-			ret = PTR_ERR(imxpriv->sata_gate_clk);
-			goto err_out;
+	if (imxpriv->type == AHCI_IMX6Q) {
+		imxpriv->gpr = syscon_regmap_lookup_by_compatible(
+							"fsl,imx6q-iomuxc-gpr");
+		if (IS_ERR(imxpriv->gpr)) {
+			dev_err(dev,
+				"failed to find fsl,imx6q-iomux-gpr regmap\n");
+			return PTR_ERR(imxpriv->gpr);
 		}
 	}
 
-	imxpriv->sata_ref_clk = devm_clk_get(dev, "sata_ref");
-	if (IS_ERR(imxpriv->sata_ref_clk)) {
-		dev_err(dev, "can't get sata_ref clock.\n");
-		ret = PTR_ERR(imxpriv->sata_ref_clk);
-		goto err_out;
-	}
+	hpriv = ahci_platform_get_resources(pdev);
+	if (IS_ERR(hpriv))
+		return PTR_ERR(hpriv);
+
+	hpriv->plat_data = imxpriv;
 
-	imxpriv->ahci_pdev = ahci_pdev;
-	platform_set_drvdata(pdev, imxpriv);
+	ret = imx_sata_enable(hpriv);
+	if (ret)
+		return ret;
 
-	mem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
-	irq = platform_get_resource(pdev, IORESOURCE_IRQ, 0);
-	if (!mem || !irq) {
-		dev_err(dev, "no mmio/irq resource\n");
-		ret = -ENOMEM;
-		goto err_out;
+	/*
+	 * Configure the HWINIT bits of the HOST_CAP and HOST_PORTS_IMPL,
+	 * and IP vendor specific register HOST_TIMER1MS.
+	 * Configure CAP_SSS (support stagered spin up).
+	 * Implement the port0.
+	 * Get the ahb clock rate, and configure the TIMER1MS register.
+	 */
+	reg_val = readl(hpriv->mmio + HOST_CAP);
+	if (!(reg_val & HOST_CAP_SSS)) {
+		reg_val |= HOST_CAP_SSS;
+		writel(reg_val, hpriv->mmio + HOST_CAP);
+	}
+	reg_val = readl(hpriv->mmio + HOST_PORTS_IMPL);
+	if (!(reg_val & 0x1)) {
+		reg_val |= 0x1;
+		writel(reg_val, hpriv->mmio + HOST_PORTS_IMPL);
 	}
 
-	res[0] = *mem;
-	res[1] = *irq;
+	reg_val = clk_get_rate(imxpriv->ahb_clk) / 1000;
+	writel(reg_val, hpriv->mmio + HOST_TIMER1MS);
 
-	ahci_dev->coherent_dma_mask = DMA_BIT_MASK(32);
-	ahci_dev->dma_mask = &ahci_dev->coherent_dma_mask;
-	ahci_dev->of_node = dev->of_node;
+	ret = ahci_platform_init_host(pdev, hpriv, &ahci_imx_port_info, 0, 0);
+	if (ret)
+		imx_sata_disable(hpriv);
 
-	if (type == AHCI_IMX6Q) {
-		imxpriv->gpr = syscon_regmap_lookup_by_compatible(
-							"fsl,imx6q-iomuxc-gpr");
-		if (IS_ERR(imxpriv->gpr)) {
-			dev_err(dev,
-				"failed to find fsl,imx6q-iomux-gpr regmap\n");
-			ret = PTR_ERR(imxpriv->gpr);
-			goto err_out;
-		}
+	return ret;
+}
 
-		/*
-		 * Set PHY Paremeters, two steps to configure the GPR13,
-		 * one write for rest of parameters, mask of first write
-		 * is 0x07fffffe, and the other one write for setting
-		 * the mpll_clk_en happens in imx_sata_clock_enable().
-		 */
-		regmap_update_bits(imxpriv->gpr, IOMUXC_GPR13,
-				   IMX6Q_GPR13_SATA_RX_EQ_VAL_MASK |
-				   IMX6Q_GPR13_SATA_RX_LOS_LVL_MASK |
-				   IMX6Q_GPR13_SATA_RX_DPLL_MODE_MASK |
-				   IMX6Q_GPR13_SATA_SPD_MODE_MASK |
-				   IMX6Q_GPR13_SATA_MPLL_SS_EN |
-				   IMX6Q_GPR13_SATA_TX_ATTEN_MASK |
-				   IMX6Q_GPR13_SATA_TX_BOOST_MASK |
-				   IMX6Q_GPR13_SATA_TX_LVL_MASK |
-				   IMX6Q_GPR13_SATA_MPLL_CLK_EN |
-				   IMX6Q_GPR13_SATA_TX_EDGE_RATE,
-				   IMX6Q_GPR13_SATA_RX_EQ_VAL_3_0_DB |
-				   IMX6Q_GPR13_SATA_RX_LOS_LVL_SATA2M |
-				   IMX6Q_GPR13_SATA_RX_DPLL_MODE_2P_4F |
-				   IMX6Q_GPR13_SATA_SPD_MODE_3P0G |
-				   IMX6Q_GPR13_SATA_MPLL_SS_EN |
-				   IMX6Q_GPR13_SATA_TX_ATTEN_9_16 |
-				   IMX6Q_GPR13_SATA_TX_BOOST_3_33_DB |
-				   IMX6Q_GPR13_SATA_TX_LVL_1_025_V);
-	}
+static void ahci_imx_host_stop(struct ata_host *host)
+{
+	struct ahci_host_priv *hpriv = host->private_data;
 
-	ret = platform_device_add_resources(ahci_pdev, res, 2);
-	if (ret)
-		goto err_out;
+	imx_sata_disable(hpriv);
+}
 
-	ret = platform_device_add_data(ahci_pdev, pdata, sizeof(*pdata));
-	if (ret)
-		goto err_out;
+static int imx_ahci_suspend(struct device *dev)
+{
+	struct ata_host *host = dev_get_drvdata(dev);
+	struct ahci_host_priv *hpriv = host->private_data;
+	int ret;
 
-	ret = platform_device_add(ahci_pdev);
-	if (ret) {
-err_out:
-		platform_device_put(ahci_pdev);
+	ret = ahci_platform_suspend_host(dev);
+	if (ret)
 		return ret;
-	}
+
+	imx_sata_disable(hpriv);
 
 	return 0;
 }
 
-static int imx_ahci_remove(struct platform_device *pdev)
+static int imx_ahci_resume(struct device *dev)
 {
-	struct imx_ahci_priv *imxpriv = platform_get_drvdata(pdev);
-	struct platform_device *ahci_pdev = imxpriv->ahci_pdev;
+	struct ata_host *host = dev_get_drvdata(dev);
+	struct ahci_host_priv *hpriv = host->private_data;
+	int ret;
 
-	platform_device_unregister(ahci_pdev);
-	return 0;
+	ret = imx_sata_enable(hpriv);
+	if (ret)
+		return ret;
+
+	return ahci_platform_resume_host(dev);
 }
 
+static SIMPLE_DEV_PM_OPS(ahci_imx_pm_ops, imx_ahci_suspend, imx_ahci_resume);
+
 static struct platform_driver imx_ahci_driver = {
 	.probe = imx_ahci_probe,
-	.remove = imx_ahci_remove,
+	.remove = ata_platform_remove_one,
 	.driver = {
 		.name = "ahci-imx",
 		.owner = THIS_MODULE,
 		.of_match_table = imx_ahci_of_match,
+		.pm = &ahci_imx_pm_ops,
 	},
 };
 module_platform_driver(imx_ahci_driver);
-- 
1.9.0




More information about the linux-arm-kernel mailing list