[PATCH v10 0/4] PHY: Add APM X-Gene SoC 15Gbps Multi-purpose PHY support
Loc Ho
lho at apm.com
Fri Feb 21 12:46:37 EST 2014
This patch adds support for APM X-Gene SoC 15Gbps Multi-purpose PHY. This
is the physical layer interface for the corresponding host controller. This
driver uses the PHY generic framework. In addition, the PHY generic
framework is patched to provide an function to set the speed of the PHY.
v10
* Update comment for function xgene_phy_force_lat_summer_cal and
xgene_phy_sata_force_gen with function style fully-winged style
v9
* Update CMU parameter setting for register 13
* Add required delay when configure CMU PLL, Manual Calibration PLL, and VCO
PLL
* Add comment for CMU PLL calibration loop delay of 10us
* Add required delay for stopping and starting summer calibrations
* Update comment for summer and latch calibration delays
* Update comment for PHY reset Rx delay and decrease max sleep time from 500
to 150us
* Always program the DFE (equalizer) setting to 0x7e00 as with original version
* Fix Tx speed selection to always using Gen3 setting when force to an
specified generation speed
v8
* Update binding documentation
* Remove XGENE_PHY_DTS and XGENE_PHY_EXT_DTS defines
* Remove support for internal clock
* Remove support for external reference CMU
* Remove the need for external reference resource DTS entry and its related
code
v7
* Add/Update PHY CMU/lane parameters and its default values
* Rename variable enable_manual_cal to preA3Chip
* Remove function phy_rd, phy_wr, and phy_wr_flush
* Change function cmu_wr, cmu_rd, cmu_toggle1to0, cmu_clrbits, cmu_setbits,
serdes_wr, serdes_rd, serdes_clrbits, and serdes_setbits to take context
instead void *
* Remove function serdes_toggle1to0
* Decrease the polling time from 10ms to 1ms on CMU calibration complete
detection
* Move all SATA specify code in function xgene_phy_hw_initialize into
function xgene_phy_hw_init_sata
* Add usleep_range after starting summer/latch calibrations
* Add usleep_range between receiver reset (function xgene_phy_reset_rxd)
* Save and restore PHY register 31 instead writing 0 in function
xgene_phy_gen_avg_val
* Update function xgene_phy_sata_force_gen programming sequences
* Add support to reset the receiver lane in function xgene_phy_set_speed
if speed is 0
* Update PHY parameters in DTS per controller
* Some minor code clean up
v6
* Move PHY document to Documentation/devicetree/binding/phy
* Remove _ADDR from all register defines
* Update clock-names property for sataphy1clk, sataphy2clk, and sataphy3clk
v5
* Update DTS binding documentation
* Remove direct clock access and use clock interface instead
* Change override parameters to decimal instead hex values
* Change apm,tx-amplitude, apm,tx-pre-cursor1, apm,tx-pre-cursor2,
apm,tx-post-cursor to be unit of uV
v4
* Update documentation with 'apm,' instead 'apm-'
* Change DTS override parameter to have 'apm,'
* Add select GENERIC_PHY to Kconfig PHY_XGENE
* Make override parameters to be pair of three values instead one
* Some minor comment and indentation changes
* Remove error register addition offset
* Add ULL to constants
* Use module_init instead subsys_initcall
* Make DTS node based on first register address
* Update override setting values
v3
* Major re-write of the code based on various review comments
* Support external clock only at the moment
* Support SATA mode only at the moment
* No UEFI support at the moment
v2
* Remove port knowledge from functions
* Make all functions static
* Remove ID completely
* Make resource requirement based on compatible type
* Rename override PHY parameters with more descriptive name
* Add override PHY parameter for per controller, per port, and per speed
* Patch the generic PHY frame to expose set_speed operation
v1
* Initial version
Signed-off-by: Loc Ho <lho at apm.com>
Signed-off-by: Tuan Phan <tphan at apm.com>
Signed-off-by: Suman Tripathi <stripathi at apm.com>
---
Loc Ho (4):
PHY: Add function set_speed to generic PHY framework
Documentation: Add APM X-Gene SoC 15Gbps Multi-purpose PHY driver
binding documentation
PHY: add APM X-Gene SoC 15Gbps Multi-purpose PHY driver
arm64: Add APM X-Gene SoC 15Gbps Multi-purpose PHY DTS entries
.../devicetree/bindings/phy/apm-xgene-phy.txt | 79 +
arch/arm64/boot/dts/apm-storm.dtsi | 75 +
drivers/phy/Kconfig | 7 +
drivers/phy/Makefile | 2 +
drivers/phy/phy-core.c | 21 +
drivers/phy/phy-xgene.c | 1826 ++++++++++++++++++++
include/linux/phy/phy.h | 8 +
7 files changed, 2018 insertions(+), 0 deletions(-)
create mode 100644 Documentation/devicetree/bindings/phy/apm-xgene-phy.txt
create mode 100644 drivers/phy/phy-xgene.c
More information about the linux-arm-kernel
mailing list