[PATCH v6 8/8] ARM: brcmstb: dts: add a reference DTS for Broadcom 7445

[Matt Porter]

On Mon, Feb 03, 2014 at 01:30:41PM -0800, Marc Carino wrote:
> Add a sample DTS which will allow bootup of a board populated
> with the BCM7445 chip.
> 
> Signed-off-by: Marc Carino <marc.ceeeee at gmail.com>
> Acked-by: Florian Fainelli <f.fainelli at gmail.com>
> ---
>  arch/arm/boot/dts/bcm7445.dts |  111 +++++++++++++++++++++++++++++++++++++++++
>  1 files changed, 111 insertions(+), 0 deletions(-)
>  create mode 100644 arch/arm/boot/dts/bcm7445.dts

Looking forward, I suspect you are going to have to move to a
bcm7445.dtsi with your board specific implementations in something like
bcm7445-myrefbrd.dts. It's probably better to split this now to
encourage inclusion of the common SoC nodes from the board specific
dts. Since it's not abstracted this way it'll encourage people to just
copy the entire bcm7445.dts for their board.

> diff --git a/arch/arm/boot/dts/bcm7445.dts b/arch/arm/boot/dts/bcm7445.dts
> new file mode 100644
> index 0000000..ffa3305
> --- /dev/null
> +++ b/arch/arm/boot/dts/bcm7445.dts
> @@ -0,0 +1,111 @@
> +/dts-v1/;
> +/include/ "skeleton.dtsi"
> +
> +/ {
> +	#address-cells = <2>;
> +	#size-cells = <2>;
> +	model = "Broadcom STB (bcm7445)";
> +	compatible = "brcm,bcm7445", "brcm,brcmstb";
> +	interrupt-parent = <&gic>;
> +
> +	chosen {};
> +
> +	memory {
> +		device_type = "memory";
> +		reg = <0x00 0x00000000 0x00 0x40000000>,
> +		      <0x00 0x40000000 0x00 0x40000000>,
> +		      <0x00 0x80000000 0x00 0x40000000>;
> +	};
> +
> +	cpus {
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +
> +		cpu at 0 {
> +			compatible = "brcm,brahma-b15";
> +			device_type = "cpu";
> +			reg = <0>;
> +		};
> +
> +		cpu at 1 {
> +			compatible = "brcm,brahma-b15";
> +			device_type = "cpu";
> +			reg = <1>;
> +		};
> +
> +		cpu at 2 {
> +			compatible = "brcm,brahma-b15";
> +			device_type = "cpu";
> +			reg = <2>;
> +		};
> +
> +		cpu at 3 {
> +			compatible = "brcm,brahma-b15";
> +			device_type = "cpu";
> +			reg = <3>;
> +		};
> +	};
> +
> +	gic: interrupt-controller at ffd00000 {
> +		compatible = "brcm,brahma-b15-gic", "arm,cortex-a15-gic";
> +		reg = <0x00 0xffd01000 0x00 0x1000>,
> +		      <0x00 0xffd02000 0x00 0x2000>,
> +		      <0x00 0xffd04000 0x00 0x2000>,
> +		      <0x00 0xffd06000 0x00 0x2000>;
> +		interrupt-controller;
> +		#interrupt-cells = <3>;
> +	};
> +
> +	timer {
> +		compatible = "arm,armv7-timer";
> +		interrupts = <1 13 0xf08>,
> +			     <1 14 0xf08>,
> +			     <1 11 0xf08>,
> +			     <1 10 0xf08>;

These should leverage the preprocessor defines that are available
e.g.
		interrupts = <GIC_PPI 13 GIC_CPU_MASK_RAW(15)|IRQ_TYPE_LEVEL_LOW>,
		...

> +	};
> +
> +	rdb {
> +		#address-cells = <1>;
> +		#size-cells = <1>;
> +		compatible = "simple-bus";
> +		ranges = <0 0x00 0xf0000000 0x1000000>;
> +
> +		serial at 406b00 {
> +			compatible = "ns16550a";
> +			reg = <0x406b00 0x20>;
> +			reg-shift = <2>;
> +			reg-io-width = <4>;
> +			interrupts = <0 75 0x4>;

same here:

			interrupt = <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>;

-Matt