[PATCH 2/3] input: touchscreen: imx25 tcq driver
Markus Pargmann
mpa at pengutronix.de
Thu Feb 20 11:21:51 EST 2014
This is a driver for the imx25 ADC/TSC module. It controls the
touchscreen conversion queue and creates a touchscreen input device.
The driver currently only supports 4 wire touchscreens. The driver uses
a simple conversion queue of precharge, touch detection, X measurement,
Y measurement, precharge and another touch detection.
This driver uses the regmap from the parent to setup some touch specific
settings in the core driver and setup a idle configuration with touch
detection.
Signed-off-by: Markus Pargmann <mpa at pengutronix.de>
---
.../bindings/input/touchscreen/fsl-mx25-tcq.txt | 29 +
drivers/input/touchscreen/Kconfig | 6 +
drivers/input/touchscreen/Makefile | 1 +
drivers/input/touchscreen/fsl-imx25-tcq.c | 589 +++++++++++++++++++++
4 files changed, 625 insertions(+)
create mode 100644 Documentation/devicetree/bindings/input/touchscreen/fsl-mx25-tcq.txt
create mode 100644 drivers/input/touchscreen/fsl-imx25-tcq.c
diff --git a/Documentation/devicetree/bindings/input/touchscreen/fsl-mx25-tcq.txt b/Documentation/devicetree/bindings/input/touchscreen/fsl-mx25-tcq.txt
new file mode 100644
index 0000000..4214a99
--- /dev/null
+++ b/Documentation/devicetree/bindings/input/touchscreen/fsl-mx25-tcq.txt
@@ -0,0 +1,29 @@
+Freescale mx25 TS conversion queue module
+
+mx25 touchscreen conversion queue module which controls the ADC unit of the
+mx25 for attached touchscreens.
+
+Required properties:
+ - compatible: Should be "fsl,imx25-tcq".
+ - reg: Memory range of the device.
+ - interrupts: Should be the interrupt number associated with this module within
+ the tscadc unit (<0>).
+ - interrupt-parent: Should be a phandle to the tscadc unit.
+ - fsl,wires: Should be '<4>' or '<5>'
+
+Optional properties:
+ - fsl,pen-debounce: Pen debounce time.
+ - fsl,pen-threshold: Pen-down threshold for the touchscreen.
+ - fsl,settling-time: Settling time in nanoseconds.
+
+This device includes two conversion queues which can be added as subnodes.
+The first queue is for the touchscreen, the second for general purpose ADC.
+
+Example:
+ tsc: tcq at 50030400 {
+ compatible = "fsl,imx25-tcq";
+ reg = <0x50030400 0x60>;
+ interrupt-parent = <&tscadc>;
+ interrupts = <0>;
+ fsl,wires = <4>;
+ };
diff --git a/drivers/input/touchscreen/Kconfig b/drivers/input/touchscreen/Kconfig
index 07e9e82..d52c055 100644
--- a/drivers/input/touchscreen/Kconfig
+++ b/drivers/input/touchscreen/Kconfig
@@ -715,6 +715,12 @@ config TOUCHSCREEN_USB_COMPOSITE
To compile this driver as a module, choose M here: the
module will be called usbtouchscreen.
+config TOUCHSCREEN_MX25
+ tristate "Freescale i.MX25 touchscreen input driver"
+ depends on MFD_MX25_TSADC
+ help
+ Enable support for touchscreen connected to your i.MX25.
+
config TOUCHSCREEN_MC13783
tristate "Freescale MC13783 touchscreen input driver"
depends on MFD_MC13XXX
diff --git a/drivers/input/touchscreen/Makefile b/drivers/input/touchscreen/Makefile
index 62801f2..c891f30 100644
--- a/drivers/input/touchscreen/Makefile
+++ b/drivers/input/touchscreen/Makefile
@@ -38,6 +38,7 @@ obj-$(CONFIG_TOUCHSCREEN_INEXIO) += inexio.o
obj-$(CONFIG_TOUCHSCREEN_INTEL_MID) += intel-mid-touch.o
obj-$(CONFIG_TOUCHSCREEN_LPC32XX) += lpc32xx_ts.o
obj-$(CONFIG_TOUCHSCREEN_MAX11801) += max11801_ts.o
+obj-$(CONFIG_TOUCHSCREEN_MX25) += fsl-imx25-tcq.o
obj-$(CONFIG_TOUCHSCREEN_MC13783) += mc13783_ts.o
obj-$(CONFIG_TOUCHSCREEN_MCS5000) += mcs5000_ts.o
obj-$(CONFIG_TOUCHSCREEN_MIGOR) += migor_ts.o
diff --git a/drivers/input/touchscreen/fsl-imx25-tcq.c b/drivers/input/touchscreen/fsl-imx25-tcq.c
new file mode 100644
index 0000000..436cc8b
--- /dev/null
+++ b/drivers/input/touchscreen/fsl-imx25-tcq.c
@@ -0,0 +1,589 @@
+/*
+ * Copyright 2014 Markus Pargmann, Pengutronix <mpa at pengutronix.de>
+ * Based on driver from 2011 Juergen Beisert, Pengutronix <kernel at pengutronix.de>
+ *
+ * The code contained herein is licensed under the GNU General Public
+ * License. You may obtain a copy of the GNU General Public License
+ * Version 2 or later at the following locations:
+ *
+ * http://www.opensource.org/licenses/gpl-license.html
+ * http://www.gnu.org/copyleft/gpl.html
+ *
+ * This is the driver for the imx25 TCQ (Touchscreen Conversion Queue)
+ * connected to the imx25 ADC.
+ */
+
+#include <linux/clk.h>
+#include <linux/interrupt.h>
+#include <linux/input.h>
+#include <linux/mfd/imx25-tsadc.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+
+static const char mx25_tcq_name[] = "mx25-tcq";
+
+enum mx25_tcq_mode {
+ MX25_TS_4WIRE,
+};
+
+struct mx25_tcq_priv {
+ struct regmap *regs;
+ struct regmap *core_regs;
+ struct input_dev *idev;
+ enum mx25_tcq_mode mode;
+ unsigned int pen_threshold;
+ unsigned int sample_count;
+ unsigned int expected_samples;
+ unsigned int repeat_wait;
+ unsigned int pen_debounce;
+ unsigned int settling_time;
+ struct clk *clk;
+};
+
+static struct regmap_config mx25_tcq_regconfig = {
+ .fast_io = true,
+ .max_register = 0x5c,
+ .reg_bits = 32,
+ .val_bits = 32,
+ .reg_stride = 4,
+};
+
+static struct of_device_id mx25_tcq_ids[] = {
+ { .compatible = "fsl,imx25-tcq", },
+ { /* Senitel */ }
+};
+
+#define TSC_4WIRE_PRE_INDEX 0
+#define TSC_4WIRE_X_INDEX 1
+#define TSC_4WIRE_Y_INDEX 2
+#define TSC_4WIRE_POST_INDEX 3
+#define TSC_4WIRE_LEAVE 4
+
+#define MX25_TSC_DEF_THRESHOLD 80
+#define TSC_MAX_SAMPLES 16
+
+
+enum mx25_adc_configurations {
+ MX25_CFG_PRECHARGE = 0,
+ MX25_CFG_TOUCH_DETECT,
+ MX25_CFG_X_MEASUREMENT,
+ MX25_CFG_Y_MEASUREMENT,
+};
+
+#define MX25_PRECHARGE_VALUE (\
+ MX25_ADCQ_CFG_YPLL_OFF | \
+ MX25_ADCQ_CFG_XNUR_OFF | \
+ MX25_ADCQ_CFG_XPUL_HIGH | \
+ MX25_ADCQ_CFG_REFP_INT | \
+ MX25_ADCQ_CFG_IN_XP | \
+ MX25_ADCQ_CFG_REFN_NGND2 | \
+ MX25_ADCQ_CFG_IGS)
+
+#define MX25_TOUCH_DETECT_VALUE (\
+ MX25_ADCQ_CFG_YNLR | \
+ MX25_ADCQ_CFG_YPLL_OFF | \
+ MX25_ADCQ_CFG_XNUR_OFF | \
+ MX25_ADCQ_CFG_XPUL_OFF | \
+ MX25_ADCQ_CFG_REFP_INT | \
+ MX25_ADCQ_CFG_IN_XP | \
+ MX25_ADCQ_CFG_REFN_NGND2 | \
+ MX25_ADCQ_CFG_PENIACK)
+
+static void imx25_setup_queue_cfgs(struct mx25_tcq_priv *priv,
+ unsigned int settling_time)
+{
+ u32 precharge_cfg =
+ MX25_PRECHARGE_VALUE |
+ MX25_ADCQ_CFG_SETTLING_TIME(settling_time);
+ u32 touch_detect_cfg =
+ MX25_TOUCH_DETECT_VALUE |
+ MX25_ADCQ_CFG_NOS(1) |
+ MX25_ADCQ_CFG_SETTLING_TIME(settling_time);
+
+ regmap_write(priv->core_regs, MX25_TSC_TICR, precharge_cfg);
+
+ /* PRECHARGE */
+ regmap_write(priv->regs, MX25_ADCQ_CFG(MX25_CFG_PRECHARGE),
+ precharge_cfg);
+
+ /* TOUCH_DETECT */
+ regmap_write(priv->regs, MX25_ADCQ_CFG(MX25_CFG_TOUCH_DETECT),
+ touch_detect_cfg);
+
+ /* X Measurement */
+ regmap_write(priv->regs, MX25_ADCQ_CFG(MX25_CFG_X_MEASUREMENT),
+ MX25_ADCQ_CFG_YPLL_OFF |
+ MX25_ADCQ_CFG_XNUR_LOW |
+ MX25_ADCQ_CFG_XPUL_HIGH |
+ MX25_ADCQ_CFG_REFP_XP |
+ MX25_ADCQ_CFG_IN_YP |
+ MX25_ADCQ_CFG_REFN_XN |
+ MX25_ADCQ_CFG_NOS(priv->sample_count) |
+ MX25_ADCQ_CFG_SETTLING_TIME(settling_time));
+
+ /* Y Measurement */
+ regmap_write(priv->regs, MX25_ADCQ_CFG(MX25_CFG_Y_MEASUREMENT),
+ MX25_ADCQ_CFG_YNLR |
+ MX25_ADCQ_CFG_YPLL_HIGH |
+ MX25_ADCQ_CFG_XNUR_OFF |
+ MX25_ADCQ_CFG_XPUL_OFF |
+ MX25_ADCQ_CFG_REFP_YP |
+ MX25_ADCQ_CFG_IN_XP |
+ MX25_ADCQ_CFG_REFN_YN |
+ MX25_ADCQ_CFG_NOS(priv->sample_count) |
+ MX25_ADCQ_CFG_SETTLING_TIME(settling_time));
+
+ /* Enable the touch detection right now */
+ regmap_write(priv->core_regs, MX25_TSC_TICR, touch_detect_cfg |
+ MX25_ADCQ_CFG_IGS);
+}
+
+static int imx25_setup_queue_4wire(struct mx25_tcq_priv *priv,
+ unsigned settling_time, int *items)
+{
+ imx25_setup_queue_cfgs(priv, settling_time);
+
+ /* Setup the conversion queue */
+ regmap_write(priv->regs, MX25_ADCQ_ITEM_7_0,
+ MX25_ADCQ_ITEM(0, MX25_CFG_PRECHARGE) |
+ MX25_ADCQ_ITEM(1, MX25_CFG_TOUCH_DETECT) |
+ MX25_ADCQ_ITEM(2, MX25_CFG_X_MEASUREMENT) |
+ MX25_ADCQ_ITEM(3, MX25_CFG_Y_MEASUREMENT) |
+ MX25_ADCQ_ITEM(4, MX25_CFG_PRECHARGE) |
+ MX25_ADCQ_ITEM(5, MX25_CFG_TOUCH_DETECT));
+
+ /* We measure X/Y with 'sample_count' number of samples and execute a
+ * touch detection twice, with 1 sample each */
+ priv->expected_samples = priv->sample_count * 2 + 2;
+ *items = 6;
+
+ return 0;
+}
+
+static void mx25_tcq_disable_touch_irq(struct mx25_tcq_priv *priv)
+{
+ regmap_update_bits(priv->regs, MX25_ADCQ_CR, MX25_ADCQ_CR_PDMSK,
+ MX25_ADCQ_CR_PDMSK);
+}
+
+static void mx25_tcq_enable_touch_irq(struct mx25_tcq_priv *priv)
+{
+ regmap_update_bits(priv->regs, MX25_ADCQ_CR, MX25_ADCQ_CR_PDMSK, 0);
+}
+
+static void mx25_tcq_disable_fifo_irq(struct mx25_tcq_priv *priv)
+{
+ regmap_update_bits(priv->regs, MX25_ADCQ_MR, MX25_ADCQ_MR_FDRY_IRQ,
+ MX25_ADCQ_MR_FDRY_IRQ);
+}
+
+static void mx25_tcq_enable_fifo_irq(struct mx25_tcq_priv *priv)
+{
+ regmap_update_bits(priv->regs, MX25_ADCQ_MR, MX25_ADCQ_MR_FDRY_IRQ, 0);
+}
+
+static void mx25_tcq_force_queue_start(struct mx25_tcq_priv *priv)
+{
+ regmap_update_bits(priv->regs, MX25_ADCQ_CR, MX25_ADCQ_CR_FQS,
+ MX25_ADCQ_CR_FQS);
+
+ regmap_update_bits(priv->regs, MX25_ADCQ_CR, MX25_ADCQ_CR_FQS, 0);
+}
+
+static void mx25_tcq_force_queue_stop(struct mx25_tcq_priv *priv)
+{
+ regmap_update_bits(priv->regs, MX25_ADCQ_CR, MX25_ADCQ_CR_FQS, 0);
+}
+
+static void mx25_tcq_fifo_reset(struct mx25_tcq_priv *priv)
+{
+ u32 tcqcr;
+
+ regmap_read(priv->regs, MX25_ADCQ_CR, &tcqcr);
+ regmap_update_bits(priv->regs, MX25_ADCQ_CR, MX25_ADCQ_CR_FRST,
+ MX25_ADCQ_CR_FRST);
+ regmap_update_bits(priv->regs, MX25_ADCQ_CR, MX25_ADCQ_CR_FRST,
+ 0);
+ regmap_write(priv->regs, MX25_ADCQ_CR, tcqcr);
+}
+
+static void mx25_tcq_re_enable_touch_detection(struct mx25_tcq_priv *priv)
+{
+ /* stop the queue from looping */
+ mx25_tcq_force_queue_stop(priv);
+
+ /* for a clean touch detection, preload the X plane */
+ regmap_write(priv->core_regs, MX25_TSC_TICR, MX25_PRECHARGE_VALUE);
+
+ /* waste some time now to pre-load the X plate to high voltage */
+ mx25_tcq_fifo_reset(priv);
+
+ /* re-enable the detection right now */
+ regmap_write(priv->core_regs, MX25_TSC_TICR, MX25_TOUCH_DETECT_VALUE |
+ MX25_ADCQ_CFG_IGS);
+
+ regmap_update_bits(priv->regs, MX25_ADCQ_SR, MX25_ADCQ_SR_PD,
+ MX25_ADCQ_SR_PD);
+
+ /* enable the pen down event to be a source for the interrupt */
+ regmap_update_bits(priv->regs, MX25_ADCQ_MR, MX25_ADCQ_MR_PD_IRQ, 0);
+
+ /* lets fire the next IRQ if someone touches the touchscreen */
+ mx25_tcq_enable_touch_irq(priv);
+}
+
+static int mx25_tcq_create_event_for_4wire(struct mx25_tcq_priv *priv,
+ u32 *sample_buf, int samples)
+{
+ unsigned int x_pos = 0;
+ unsigned int y_pos = 0;
+ unsigned int touch_pre = 0;
+ unsigned int touch_post = 0;
+ unsigned i;
+ int ret = 0;
+
+ for (i = 0; i < samples; i++) {
+ unsigned int index = MX25_ADCQ_FIFO_ID(sample_buf[i]);
+ unsigned int val = MX25_ADCQ_FIFO_DATA(sample_buf[i]);
+
+ switch (index) {
+ case 1:
+ touch_pre = val;
+ break;
+ case 2:
+ x_pos = val;
+ break;
+ case 3:
+ y_pos = val;
+ break;
+ case 5:
+ touch_post = val;
+ break;
+ default:
+ ret = -EINVAL;
+ break;
+ }
+ }
+
+ if (ret == 0 && samples != 0) {
+ /*
+ * only if both touch measures are below a treshold,
+ * the position is valid
+ */
+ if (touch_pre < priv->pen_threshold &&
+ touch_post < priv->pen_threshold) {
+ /* valid samples, generate a report */
+ x_pos /= priv->sample_count;
+ y_pos /= priv->sample_count;
+ input_report_abs(priv->idev, ABS_X, x_pos);
+ input_report_abs(priv->idev, ABS_Y, y_pos);
+ input_report_key(priv->idev, BTN_TOUCH,
+ 0xfff - ((touch_pre + touch_post) / 2));
+ input_sync(priv->idev);
+
+ /* get next sample */
+ mx25_tcq_force_queue_start(priv);
+ mx25_tcq_enable_fifo_irq(priv);
+ } else {
+ if (touch_pre >= priv->pen_threshold &&
+ touch_post >= priv->pen_threshold) {
+ /*
+ * if both samples are invalid,
+ * generate a release report
+ */
+ input_report_key(priv->idev, BTN_TOUCH, 0);
+ input_sync(priv->idev);
+ mx25_tcq_re_enable_touch_detection(priv);
+ } else {
+ /*
+ * if only one of both touch measurements are
+ * below the threshold, still some bouncing
+ * happens. Take additional samples in this
+ * case to be sure
+ */
+ mx25_tcq_force_queue_start(priv);
+ mx25_tcq_enable_fifo_irq(priv);
+ }
+ }
+ }
+
+ return ret;
+}
+
+static irqreturn_t mx25_tcq_irq_thread(int irq, void *dev_id)
+{
+ struct mx25_tcq_priv *priv = (struct mx25_tcq_priv *) dev_id;
+ u32 sample_buf[TSC_MAX_SAMPLES];
+ int samples = 0;
+
+ /* read all samples */
+ while (1) {
+ u32 stats;
+
+ regmap_read(priv->regs, MX25_ADCQ_SR, &stats);
+ if (stats & MX25_ADCQ_SR_EMPT)
+ break;
+
+ if (samples < TSC_MAX_SAMPLES) {
+ regmap_read(priv->regs, MX25_ADCQ_FIFO,
+ &sample_buf[samples]);
+ ++samples;
+ } else {
+ u32 discarded;
+ /* discard samples */
+ regmap_read(priv->regs, MX25_ADCQ_FIFO, &discarded);
+ }
+ }
+
+ mx25_tcq_create_event_for_4wire(priv, sample_buf, samples);
+
+ return IRQ_HANDLED;
+}
+
+static irqreturn_t mx25_tcq_irq(int irq, void *dev_id)
+{
+ struct mx25_tcq_priv *priv = (struct mx25_tcq_priv *)dev_id;
+ u32 stat;
+ int ret = IRQ_HANDLED;
+
+ regmap_read(priv->regs, MX25_ADCQ_SR, &stat);
+
+ if (stat & (MX25_ADCQ_SR_FRR | MX25_ADCQ_SR_FUR | MX25_ADCQ_SR_FOR))
+ mx25_tcq_fifo_reset(priv);
+
+ if (stat & MX25_ADCQ_SR_PD) {
+ mx25_tcq_disable_touch_irq(priv);
+ mx25_tcq_force_queue_start(priv);
+ mx25_tcq_enable_fifo_irq(priv);
+ }
+
+ if (stat & MX25_ADCQ_SR_FDRY) {
+ mx25_tcq_disable_fifo_irq(priv);
+ ret = IRQ_WAKE_THREAD;
+ }
+
+ regmap_update_bits(priv->regs, MX25_ADCQ_SR, MX25_ADCQ_SR_FRR |
+ MX25_ADCQ_SR_FUR | MX25_ADCQ_SR_FOR | MX25_ADCQ_SR_PD |
+ MX25_ADCQ_SR_EOQ,
+ MX25_ADCQ_SR_FRR |
+ MX25_ADCQ_SR_FUR | MX25_ADCQ_SR_FOR | MX25_ADCQ_SR_PD |
+ MX25_ADCQ_SR_EOQ);
+
+ return ret;
+}
+
+/* configure the statemachine for a 4-wire touchscreen */
+static int mx25_tcq_init(struct mx25_tcq_priv *priv)
+{
+ u32 tgcr;
+ unsigned int ipg_div;
+ unsigned int adc_period;
+ unsigned int repeat_wait;
+ unsigned int debounce_cnt;
+ unsigned int settling_time;
+ int itemct;
+ int ret;
+
+ regmap_read(priv->core_regs, MX25_TSC_TGCR, &tgcr);
+ ipg_div = max_t(unsigned int, 4, MX25_TGCR_GET_ADCCLK(tgcr));
+ adc_period = clk_get_rate(priv->clk) / (ipg_div * 2 + 2);
+ repeat_wait = fls(DIV_ROUND_UP(priv->repeat_wait, adc_period));
+ debounce_cnt = DIV_ROUND_UP(priv->pen_debounce, adc_period * 8) - 1;
+ settling_time = DIV_ROUND_UP(priv->settling_time, adc_period);
+
+
+ /* Reset */
+ regmap_write(priv->regs, MX25_ADCQ_CR, MX25_ADCQ_CR_QRST |
+ MX25_ADCQ_CR_FRST);
+ regmap_update_bits(priv->regs, MX25_ADCQ_CR, MX25_ADCQ_CR_QRST |
+ MX25_ADCQ_CR_FRST, 0);
+
+ /* up to 128 * 8 ADC clocks are possible */
+ if (debounce_cnt > 127)
+ debounce_cnt = 127;
+
+ if (repeat_wait > 15)
+ repeat_wait = 15;
+
+ regmap_update_bits(priv->regs, MX25_ADCQ_CR, MX25_ADCQ_CR_RWAIT_MASK,
+ MX25_ADCQ_CR_RWAIT(repeat_wait));
+
+ ret = imx25_setup_queue_4wire(priv, 0x0, &itemct);
+ if (ret)
+ return ret;
+
+ regmap_update_bits(priv->regs, MX25_ADCQ_CR, MX25_ADCQ_CR_LITEMID_MASK |
+ MX25_ADCQ_CR_WMRK_MASK,
+ MX25_ADCQ_CR_LITEMID(itemct - 1) |
+ MX25_ADCQ_CR_WMRK(priv->expected_samples - 1));
+
+ /* setup debounce count */
+ regmap_update_bits(priv->core_regs, MX25_TSC_TGCR,
+ MX25_TGCR_PDBTIME_MASK,
+ MX25_TGCR_PDBTIME(debounce_cnt));
+
+ /* enable debounce */
+ regmap_update_bits(priv->core_regs, MX25_TSC_TGCR, MX25_TGCR_PDBEN,
+ MX25_TGCR_PDBEN);
+ regmap_update_bits(priv->core_regs, MX25_TSC_TGCR, MX25_TGCR_PDEN,
+ MX25_TGCR_PDEN);
+
+ /* enable the engine on demand */
+ regmap_update_bits(priv->regs, MX25_ADCQ_CR, MX25_ADCQ_CR_QSM_FQS,
+ MX25_ADCQ_CR_QSM_FQS);
+
+ mx25_tcq_re_enable_touch_detection(priv);
+
+ return 0;
+}
+
+static int mx25_tcq_parse_dt(struct platform_device *pdev,
+ struct mx25_tcq_priv *priv)
+{
+ struct device_node *np = pdev->dev.of_node;
+ u32 wires;
+ int ret;
+
+ /* Setup defaults */
+ priv->pen_threshold = 500;
+ priv->sample_count = 3;
+ priv->repeat_wait = 15000000;
+ priv->pen_debounce = 1000000;
+ priv->settling_time = 250000;
+
+ ret = of_property_read_u32(np, "fsl,wires", &wires);
+ if (ret) {
+ dev_err(&pdev->dev, "Failed to find fsl,wires properties\n");
+ return ret;
+ }
+
+ if (wires == 4) {
+ priv->mode = MX25_TS_4WIRE;
+ } else {
+ dev_err(&pdev->dev, "%u-wire mode not supported\n", wires);
+ return -EINVAL;
+ }
+
+ /* These are optional, we don't care about the return values */
+ of_property_read_u32(np, "fsl,pen-threshold", &priv->pen_threshold);
+ of_property_read_u32(np, "fsl,settling-time", &priv->settling_time);
+ of_property_read_u32(np, "fsl,pen-debounce", &priv->pen_debounce);
+
+ return 0;
+}
+
+static int mx25_tcq_probe(struct platform_device *pdev)
+{
+ struct device *dev = &pdev->dev;
+ struct input_dev *idev;
+ struct mx25_tcq_priv *priv;
+ struct resource *res;
+ void __iomem *mem;
+ int ret;
+ int irq;
+
+ priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
+ if (!priv)
+ return -ENOMEM;
+
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ mem = devm_ioremap_resource(dev, res);
+ if (!mem) {
+ dev_err(dev, "Failed to get iomem");
+ return -ENOMEM;
+ }
+
+ ret = mx25_tcq_parse_dt(pdev, priv);
+ if (ret)
+ return ret;
+
+ priv->regs = devm_regmap_init_mmio(dev, mem, &mx25_tcq_regconfig);
+ if (IS_ERR(priv->regs)) {
+ dev_err(dev, "Failed to initialize regmap\n");
+ return PTR_ERR(priv->regs);
+ }
+
+ irq = platform_get_irq(pdev, 0);
+ if (irq < 0) {
+ dev_err(dev, "Failed to get IRQ\n");
+ return irq;
+ }
+
+ ret = devm_request_threaded_irq(dev, irq, mx25_tcq_irq,
+ mx25_tcq_irq_thread, IRQF_ONESHOT, pdev->name, priv);
+ if (ret) {
+ dev_err(dev, "Failed requesting IRQ\n");
+ return ret;
+ }
+
+ idev = devm_input_allocate_device(dev);
+ if (!idev) {
+ dev_err(dev, "Failed to allocate input device\n");
+ return -ENOMEM;
+ }
+
+ idev->name = mx25_tcq_name;
+ idev->evbit[0] = BIT_MASK(EV_KEY) | BIT_MASK(EV_ABS);
+ idev->keybit[BIT_WORD(BTN_TOUCH)] = BIT_MASK(BTN_TOUCH);
+ input_set_abs_params(idev, ABS_X, 0, 0xfff, 0, 0);
+ input_set_abs_params(idev, ABS_Y, 0, 0xfff, 0, 0);
+
+ idev->id.bustype = BUS_HOST;
+
+ ret = input_register_device(idev);
+ if (ret) {
+ dev_err(dev, "Failed to register input device\n");
+ return ret;
+ }
+
+ priv->idev = idev;
+
+ priv->core_regs = mx25_tsadc_get_regmap(pdev->dev.parent);
+ priv->clk = mx25_tsadc_get_ipg(pdev->dev.parent);
+
+ ret = clk_prepare_enable(priv->clk);
+ if (ret) {
+ dev_err(dev, "Failed to enable ipg clock\n");
+ return ret;
+ }
+
+ ret = mx25_tcq_init(priv);
+ if (ret) {
+ dev_err(dev, "Failed to init tcq\n");
+ goto error_tcq_init;
+ }
+
+ platform_set_drvdata(pdev, priv);
+
+ return 0;
+
+error_tcq_init:
+ clk_disable_unprepare(priv->clk);
+ return ret;
+}
+
+static int mx25_tcq_remove(struct platform_device *pdev)
+{
+ struct mx25_tcq_priv *priv = platform_get_drvdata(pdev);
+
+ clk_disable_unprepare(priv->clk);
+
+ return 0;
+}
+
+static struct platform_driver mx25_tcq_driver = {
+ .driver = {
+ .name = "mx25-tcq",
+ .owner = THIS_MODULE,
+ .of_match_table = mx25_tcq_ids,
+ },
+ .probe = mx25_tcq_probe,
+ .remove = mx25_tcq_remove,
+};
+module_platform_driver(mx25_tcq_driver);
+
+MODULE_DESCRIPTION("TS input driver for Freescale mx25");
+MODULE_AUTHOR("Markus Pargmann <mpa at pengutronix.de>");
+MODULE_LICENSE("GPL v2");
--
1.8.5.3
More information about the linux-arm-kernel
mailing list