[PATCHv2 1/8] ARM: at91: Add at91sam9rl DT SoC support
Jean-Jacques Hiblot
jjhiblot at gmail.com
Wed Feb 19 11:19:37 EST 2014
Hi boris,
I don't know if splitting the patch is needed. For the 9261 I was
asked to keep the patch number low and the board won't boot up if the
one of the 2 patches is missing.
Jean-Jacques
2014-02-19 17:01 GMT+01:00 Boris BREZILLON <b.brezillon at overkiz.com>:
> Hi Alexandre,
>
>
> On 19/02/2014 16:32, Alexandre Belloni wrote:
>>
>> This adds preliminary DT support for the at91sam9rl.
>>
>> Signed-off-by: Alexandre Belloni <alexandre.belloni at free-electrons.com>
>> ---
>> arch/arm/boot/dts/at91sam9rl.dtsi | 628
>> ++++++++++++++++++++++++++++++++++++++
>> arch/arm/mach-at91/at91sam9rl.c | 16 +
>> 2 files changed, 644 insertions(+)
>> create mode 100644 arch/arm/boot/dts/at91sam9rl.dtsi
>>
>> diff --git a/arch/arm/boot/dts/at91sam9rl.dtsi
>> b/arch/arm/boot/dts/at91sam9rl.dtsi
>> new file mode 100644
>> index 000000000000..9a6208b046b6
>> --- /dev/null
>> +++ b/arch/arm/boot/dts/at91sam9rl.dtsi
>> @@ -0,0 +1,628 @@
>> +/*
>> + * at91sam9rl.dtsi - Device Tree Include file for AT91SAM9RL family SoC
>> + *
>> + * Copyright (C) 2014 Alexandre Belloni
>> <alexandre.belloni at free-electrons.com>
>> + *
>> + * Licensed under GPLv2 or later.
>> + */
>> +
>> +#include "skeleton.dtsi"
>> +#include <dt-bindings/pinctrl/at91.h>
>> +#include <dt-bindings/interrupt-controller/irq.h>
>> +#include <dt-bindings/gpio/gpio.h>
>> +
>> +/ {
>> + model = "Atmel AT91SAM9RL family SoC";
>> + compatible = "atmel,at91sam9rl", "atmel,at91sam9";
>> + interrupt-parent = <&aic>;
>> +
>> + aliases {
>> + serial0 = &dbgu;
>> + serial1 = &usart0;
>> + serial2 = &usart1;
>> + serial3 = &usart2;
>> + serial4 = &usart3;
>> + gpio0 = &pioA;
>> + gpio1 = &pioB;
>> + gpio2 = &pioC;
>> + gpio3 = &pioD;
>> + tcb0 = &tcb0;
>> + i2c0 = &i2c0;
>> + i2c1 = &i2c1;
>> + ssc0 = &ssc0;
>> + ssc1 = &ssc1;
>> + };
>> +
>> + cpus {
>> + #address-cells = <0>;
>> + #size-cells = <0>;
>> +
>> + cpu {
>> + compatible = "arm,arm926ej-s";
>> + device_type = "cpu";
>> + };
>> + };
>> +
>> + memory {
>> + reg = <0x20000000 0x04000000>;
>> + };
>> +
>> + ahb {
>> + compatible = "simple-bus";
>> + #address-cells = <1>;
>> + #size-cells = <1>;
>> + ranges;
>> +
>> + apb {
>> + compatible = "simple-bus";
>> + #address-cells = <1>;
>> + #size-cells = <1>;
>> + ranges;
>> +
>> + tcb0: timer at fffa0000 {
>> + compatible = "atmel,at91rm9200-tcb";
>> + reg = <0xfffa0000 0x100>;
>> + interrupts = <16 IRQ_TYPE_LEVEL_HIGH 0
>> + 17 IRQ_TYPE_LEVEL_HIGH 0
>> + 18 IRQ_TYPE_LEVEL_HIGH 0>;
>> + };
>> +
>> + mmc0: mmc at fffa4000 {
>> + compatible = "atmel,hsmci";
>> + reg = <0xfffa4000 0x600>;
>> + interrupts = <10 IRQ_TYPE_LEVEL_HIGH 0>;
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> + pinctrl-names = "default";
>> + status = "disabled";
>> + };
>> +
>> + i2c0: i2c at fffa8000 {
>> + compatible = "atmel,at91sam9260-i2c";
>> + reg = <0xfffa8000 0x100>;
>> + interrupts = <11 IRQ_TYPE_LEVEL_HIGH 6>;
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> + status = "disabled";
>> + };
>> +
>> + i2c1: i2c at fffac000 {
>> + compatible = "atmel,at91sam9260-i2c";
>> + reg = <0xfffac000 0x100>;
>> + interrupts = <12 IRQ_TYPE_LEVEL_HIGH 6>;
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> + status = "disabled";
>> + };
>> +
>> + usart0: serial at fffb0000 {
>> + compatible = "atmel,at91sam9260-usart";
>> + reg = <0xfffb0000 0x200>;
>> + interrupts = <6 IRQ_TYPE_LEVEL_HIGH 5>;
>> + atmel,use-dma-rx;
>> + atmel,use-dma-tx;
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&pinctrl_usart0>;
>> + status = "disabled";
>> + };
>> +
>> + usart1: serial at fffb4000 {
>> + compatible = "atmel,at91sam9260-usart";
>> + reg = <0xfffb4000 0x200>;
>> + interrupts = <7 IRQ_TYPE_LEVEL_HIGH 5>;
>> + atmel,use-dma-rx;
>> + atmel,use-dma-tx;
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&pinctrl_usart1>;
>> + status = "disabled";
>> + };
>> +
>> + usart2: serial at fffb8000 {
>> + compatible = "atmel,at91sam9260-usart";
>> + reg = <0xfffb8000 0x200>;
>> + interrupts = <8 IRQ_TYPE_LEVEL_HIGH 5>;
>> + atmel,use-dma-rx;
>> + atmel,use-dma-tx;
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&pinctrl_usart2>;
>> + status = "disabled";
>> + };
>> +
>> + usart3: serial at fffbc000 {
>> + compatible = "atmel,at91sam9260-usart";
>> + reg = <0xfffbc000 0x200>;
>> + interrupts = <9 IRQ_TYPE_LEVEL_HIGH 5>;
>> + atmel,use-dma-rx;
>> + atmel,use-dma-tx;
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&pinctrl_usart3>;
>> + status = "disabled";
>> + };
>> +
>> + ssc0: ssc at fffc0000 {
>> + compatible = "atmel,at91rm9200-ssc";
>> + reg = <0xfffc0000 0x4000>;
>> + interrupts = <14 IRQ_TYPE_LEVEL_HIGH 5>;
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&pinctrl_ssc0_tx
>> &pinctrl_ssc0_rx>;
>> + status = "disabled";
>> + };
>> +
>> + ssc1: ssc at fffc4000 {
>> + compatible = "atmel,at91rm9200-ssc";
>> + reg = <0xfffc4000 0x4000>;
>> + interrupts = <15 IRQ_TYPE_LEVEL_HIGH 5>;
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&pinctrl_ssc1_tx
>> &pinctrl_ssc1_rx>;
>> + status = "disabled";
>> + };
>> +
>> + spi0: spi at fffcc000 {
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> + compatible = "atmel,at91rm9200-spi";
>> + reg = <0xfffcc000 0x200>;
>> + interrupts = <13 IRQ_TYPE_LEVEL_HIGH 3>;
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&pinctrl_spi0>;
>> + status = "disabled";
>> + };
>> +
>> + adc0: adc at fffd0000 {
>> + compatible = "atmel,at91sam9260-adc";
>> + reg = <0xfffd0000 0x100>;
>> + interrupts = <20 IRQ_TYPE_LEVEL_HIGH 0>;
>> + atmel,adc-use-external-triggers;
>> + atmel,adc-channels-used = <0xf>;
>> + atmel,adc-vref = <3300>;
>> + atmel,adc-num-channels = <4>;
>> + atmel,adc-startup-time = <15>;
>> + atmel,adc-channel-base = <0x30>;
>> + atmel,adc-drdy-mask = <0x10000>;
>> + atmel,adc-status-register = <0x1c>;
>> + atmel,adc-trigger-register = <0x04>;
>> + atmel,adc-res = <8 10>;
>> + atmel,adc-res-names = "lowres", "highres";
>> + atmel,adc-use-res = "highres";
>> +
>> + trigger at 0 {
>> + trigger-name = "timer-counter-0";
>> + trigger-value = <0x1>;
>> + };
>> + trigger at 1 {
>> + trigger-name = "timer-counter-1";
>> + trigger-value = <0x3>;
>> + };
>> +
>> + trigger at 2 {
>> + trigger-name = "timer-counter-2";
>> + trigger-value = <0x5>;
>> + };
>> +
>> + trigger at 3 {
>> + trigger-name = "external";
>> + trigger-value = <0x13>;
>> + trigger-external;
>> + };
>> + };
>> +
>> + usb0: gadget at fffd4000 {
>> + compatible = "atmel,at91rm9200-udc";
>> + reg = <0xfffd4000 0x4000>;
>> + interrupts = <22 IRQ_TYPE_LEVEL_HIGH 2>;
>> + status = "disabled";
>> + };
>> +
>> + ramc0: ramc at ffffea00 {
>> + compatible = "atmel,at91sam9260-sdramc";
>> + reg = <0xffffea00 0x200>;
>> + };
>> +
>> + aic: interrupt-controller at fffff000 {
>> + #interrupt-cells = <3>;
>> + compatible = "atmel,at91rm9200-aic";
>> + interrupt-controller;
>> + reg = <0xfffff000 0x200>;
>> + atmel,external-irqs = <31>;
>> + };
>> +
>> + dbgu: serial at fffff200 {
>> + compatible = "atmel,at91sam9260-usart";
>> + reg = <0xfffff200 0x200>;
>> + interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>;
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&pinctrl_dbgu>;
>> + status = "disabled";
>> + };
>> +
>> + pinctrl at fffff400 {
>> + #address-cells = <1>;
>> + #size-cells = <1>;
>> + compatible = "atmel,at91rm9200-pinctrl",
>> "simple-bus";
>> + ranges = <0xfffff400 0xfffff400 0x800>;
>> +
>> + atmel,mux-mask = <
>> + /* A B */
>> + 0xffffffff 0xe05c6738 /* pioA */
>> + 0xffffffff 0x0000c780 /* pioB */
>> + 0xffffffff 0xe3ffff0e /* pioC */
>> + 0x003fffff 0x0001ff3c /* pioD */
>> + >;
>> +
>> + /* shared pinctrl settings */
>> + dbgu {
>> + pinctrl_dbgu: dbgu-0 {
>> + atmel,pins =
>> + <AT91_PIOA 21
>> AT91_PERIPH_A AT91_PINCTRL_NONE
>> + AT91_PIOA 22
>> AT91_PERIPH_A AT91_PINCTRL_PULL_UP>;
>> + };
>> + };
>> +
>> + usart0 {
>> + pinctrl_usart0: usart0-0 {
>> + atmel,pins =
>> + <AT91_PIOA 6
>> AT91_PERIPH_A AT91_PINCTRL_NONE
>> + AT91_PIOA 7
>> AT91_PERIPH_A AT91_PINCTRL_PULL_UP>;
>> + };
>> +
>> + pinctrl_usart0_rts: usart0_rts-0 {
>> + atmel,pins =
>> + <AT91_PIOA 9
>> AT91_PERIPH_A AT91_PINCTRL_NONE>;
>> + };
>> +
>> + pinctrl_usart0_cts: usart0_cts-0 {
>> + atmel,pins =
>> + <AT91_PIOA 10
>> AT91_PERIPH_A AT91_PINCTRL_NONE>;
>> + };
>> +
>> + pinctrl_usart0_dtr_dsr:
>> usart0_dtr_dsr-0 {
>> + atmel,pins =
>> + <AT91_PIOD 14
>> AT91_PERIPH_A AT91_PINCTRL_NONE
>> + AT91_PIOD 15
>> AT91_PERIPH_A AT91_PINCTRL_NONE>;
>> + };
>> +
>> + pinctrl_usart0_dcd: usart0_dcd-0 {
>> + atmel,pins =
>> + <AT91_PIOD 16
>> AT91_PERIPH_A AT91_PINCTRL_NONE>;
>> + };
>> +
>> + pinctrl_usart0_ri: usart0_ri-0 {
>> + atmel,pins =
>> + <AT91_PIOD 17
>> AT91_PERIPH_A AT91_PINCTRL_NONE>;
>> + };
>> +
>> + pinctrl_usart0_sck: usart0_sck-0 {
>> + atmel,pins =
>> + <AT91_PIOA 8
>> AT91_PERIPH_A AT91_PINCTRL_NONE>;
>> + };
>> + };
>> +
>> + usart1 {
>> + pinctrl_usart1: usart1-0 {
>> + atmel,pins =
>> + /*TODO check pullup
>> necessary*/
>> + <AT91_PIOA 11
>> AT91_PERIPH_A AT91_PINCTRL_PULL_UP
>> + AT91_PIOA 12
>> AT91_PERIPH_A AT91_PINCTRL_NONE>;
>> + };
>> +
>> + pinctrl_usart1_rts: usart1_rts-0 {
>> + atmel,pins =
>> + <AT91_PIOA 18
>> AT91_PERIPH_B AT91_PINCTRL_NONE>;
>> + };
>> +
>> + pinctrl_usart1_cts: usart1_cts-0 {
>> + atmel,pins =
>> + <AT91_PIOA 19
>> AT91_PERIPH_B AT91_PINCTRL_NONE>;
>> + };
>> +
>> + pinctrl_usart1_sck: usart1_sck-0 {
>> + atmel,pins =
>> + <AT91_PIOD 2
>> AT91_PERIPH_B AT91_PINCTRL_NONE>;
>> + };
>> + };
>> +
>> + usart2 {
>> + pinctrl_usart2: usart2-0 {
>> + atmel,pins =
>> + <AT91_PIOA 13
>> AT91_PERIPH_A AT91_PINCTRL_PULL_UP
>> + AT91_PIOA 14
>> AT91_PERIPH_A AT91_PINCTRL_NONE>;
>> + };
>> +
>> + pinctrl_usart2_rts: usart2_rts-0 {
>> + atmel,pins =
>> + <AT91_PIOA 29
>> AT91_PERIPH_A AT91_PINCTRL_NONE>;
>> + };
>> +
>> + pinctrl_usart2_cts: usart2_cts-0 {
>> + atmel,pins =
>> + <AT91_PIOA 30
>> AT91_PERIPH_A AT91_PINCTRL_NONE>;
>> + };
>> +
>> + pinctrl_usart2_sck: usart2_sck-0 {
>> + atmel,pins =
>> + <AT91_PIOD 9
>> AT91_PERIPH_A AT91_PINCTRL_NONE>;
>> + };
>> + };
>> +
>> + usart3 {
>> + pinctrl_usart3: usart3-0 {
>> + atmel,pins =
>> + <AT91_PIOB 0
>> AT91_PERIPH_A AT91_PINCTRL_PULL_UP
>> + AT91_PIOB 1
>> AT91_PERIPH_A AT91_PINCTRL_NONE>;
>> + };
>> +
>> + pinctrl_usart3_rts: usart3_rts-0 {
>> + atmel,pins =
>> + <AT91_PIOD 4
>> AT91_PERIPH_B AT91_PINCTRL_NONE>;
>> + };
>> +
>> + pinctrl_usart3_cts: usart3_cts-0 {
>> + atmel,pins =
>> + <AT91_PIOD 3
>> AT91_PERIPH_B AT91_PINCTRL_NONE>;
>> + };
>> +
>> + pinctrl_usart3_sck: usart3_sck-0 {
>> + atmel,pins =
>> + <AT91_PIOA 20
>> AT91_PERIPH_B AT91_PINCTRL_NONE>;
>> + };
>> + };
>> +
>> + nand {
>> + pinctrl_nand: nand-0 {
>> + atmel,pins =
>> + <AT91_PIOD 17
>> AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP
>> + AT91_PIOB 6
>> AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP>;
>> + };
>> +
>> + pinctrl_nand0_ale_cle:
>> nand_ale_cle-0 {
>> + atmel,pins =
>> + <AT91_PIOB 2
>> AT91_PERIPH_A AT91_PINCTRL_NONE
>> + AT91_PIOB 3
>> AT91_PERIPH_A AT91_PINCTRL_NONE>;
>> + };
>> +
>> + pinctrl_nand0_oe_we: nand_oe_we-0
>> {
>> + atmel,pins =
>> + <AT91_PIOB 4
>> AT91_PERIPH_A AT91_PINCTRL_NONE
>> + AT91_PIOB 5
>> AT91_PERIPH_A AT91_PINCTRL_NONE>;
>> + };
>> +
>> + pinctrl_nand0_cs: nand_cs-0 {
>> + atmel,pins =
>> + <AT91_PIOB 6
>> AT91_PERIPH_A AT91_PINCTRL_NONE>;
>> + };
>> + };
>> +
>> + mmc0 {
>> + pinctrl_mmc0_clk: mmc0_clk-0 {
>> + atmel,pins =
>> + <AT91_PIOA 2
>> AT91_PERIPH_A AT91_PINCTRL_NONE>;
>> + };
>> +
>> + pinctrl_mmc0_slot0_cmd_dat0:
>> mmc0_slot0_cmd_dat0-0 {
>> + atmel,pins =
>> + <AT91_PIOA 0
>> AT91_PERIPH_A AT91_PINCTRL_PULL_UP
>> + AT91_PIOA 1
>> AT91_PERIPH_A AT91_PINCTRL_PULL_UP>;
>> + };
>> +
>> + pinctrl_mmc0_slot0_dat1_3:
>> mmc0_slot0_dat1_3-0 {
>> + atmel,pins =
>> + <AT91_PIOA 3
>> AT91_PERIPH_A AT91_PINCTRL_PULL_UP
>> + AT91_PIOA 4
>> AT91_PERIPH_A AT91_PINCTRL_PULL_UP
>> + AT91_PIOA 5
>> AT91_PERIPH_A AT91_PINCTRL_PULL_UP>;
>> + };
>> + };
>> +
>> + ssc0 {
>> + pinctrl_ssc0_tx: ssc0_tx-0 {
>> + atmel,pins =
>> + <AT91_PIOA 15
>> AT91_PERIPH_A AT91_PINCTRL_NONE
>> + AT91_PIOC 0
>> AT91_PERIPH_A AT91_PINCTRL_NONE
>> + AT91_PIOC 1
>> AT91_PERIPH_A AT91_PINCTRL_NONE>;
>> + };
>> +
>> + pinctrl_ssc0_rx: ssc0_rx-0 {
>> + atmel,pins =
>> + <AT91_PIOA 10
>> AT91_PERIPH_B AT91_PINCTRL_NONE
>> + AT91_PIOA 16
>> AT91_PERIPH_A AT91_PINCTRL_NONE
>> + AT91_PIOA 22
>> AT91_PERIPH_B AT91_PINCTRL_NONE>;
>> + };
>> + };
>> +
>> + ssc1 {
>> + pinctrl_ssc1_tx: ssc1_tx-0 {
>> + atmel,pins =
>> + <AT91_PIOA 13
>> AT91_PERIPH_B AT91_PINCTRL_NONE
>> + AT91_PIOA 29
>> AT91_PERIPH_B AT91_PINCTRL_NONE
>> + AT91_PIOA 30
>> AT91_PERIPH_B AT91_PINCTRL_NONE>;
>> + };
>> +
>> + pinctrl_ssc1_rx: ssc1_rx-0 {
>> + atmel,pins =
>> + <AT91_PIOA 8
>> AT91_PERIPH_B AT91_PINCTRL_NONE
>> + AT91_PIOA 9
>> AT91_PERIPH_B AT91_PINCTRL_NONE
>> + AT91_PIOA 14
>> AT91_PERIPH_B AT91_PINCTRL_NONE>;
>> + };
>> + };
>> +
>> + spi0 {
>> + pinctrl_spi0: spi0-0 {
>> + atmel,pins =
>> + <AT91_PIOA 25
>> AT91_PERIPH_A AT91_PINCTRL_NONE
>> + AT91_PIOA 26
>> AT91_PERIPH_A AT91_PINCTRL_NONE
>> + AT91_PIOA 27
>> AT91_PERIPH_A AT91_PINCTRL_NONE>;
>> + };
>> + };
>> +
>> + i2c_gpio0 {
>> + pinctrl_i2c_gpio0: i2c_gpio0-0 {
>> + atmel,pins =
>> + <AT91_PIOA 23
>> AT91_PERIPH_GPIO AT91_PINCTRL_MULTI_DRIVE
>> + AT91_PIOA 24
>> AT91_PERIPH_GPIO AT91_PINCTRL_MULTI_DRIVE>;
>> + };
>> + };
>> +
>> + i2c_gpio1 {
>> + pinctrl_i2c_gpio1: i2c_gpio1-0 {
>> + atmel,pins =
>> + <AT91_PIOD 10
>> AT91_PERIPH_GPIO AT91_PINCTRL_MULTI_DRIVE
>> + AT91_PIOD 11
>> AT91_PERIPH_GPIO AT91_PINCTRL_MULTI_DRIVE>;
>> + };
>> + };
>> +
>> + tcb0 {
>> + pinctrl_tcb0_tclk0: tcb0_tclk0-0 {
>> + atmel,pins = <AT91_PIOA 3
>> AT91_PERIPH_B AT91_PINCTRL_NONE>;
>> + };
>> +
>> + pinctrl_tcb0_tclk1: tcb0_tclk1-0 {
>> + atmel,pins = <AT91_PIOC 31
>> AT91_PERIPH_B AT91_PINCTRL_NONE>;
>> + };
>> +
>> + pinctrl_tcb0_tclk2: tcb0_tclk2-0 {
>> + atmel,pins = <AT91_PIOD 21
>> AT91_PERIPH_A AT91_PINCTRL_NONE>;
>> + };
>> +
>> + pinctrl_tcb0_tioa0: tcb0_tioa0-0 {
>> + atmel,pins = <AT91_PIOA 4
>> AT91_PERIPH_B AT91_PINCTRL_NONE>;
>> + };
>> +
>> + pinctrl_tcb0_tioa1: tcb0_tioa1-0 {
>> + atmel,pins = <AT91_PIOC 29
>> AT91_PERIPH_B AT91_PINCTRL_NONE>;
>> + };
>> +
>> + pinctrl_tcb0_tioa2: tcb0_tioa2-0 {
>> + atmel,pins = <AT91_PIOD 10
>> AT91_PERIPH_B AT91_PINCTRL_NONE>;
>> + };
>> +
>> + pinctrl_tcb0_tiob0: tcb0_tiob0-0 {
>> + atmel,pins = <AT91_PIOA 5
>> AT91_PERIPH_B AT91_PINCTRL_NONE>;
>> + };
>> +
>> + pinctrl_tcb0_tiob1: tcb0_tiob1-0 {
>> + atmel,pins = <AT91_PIOC 30
>> AT91_PERIPH_B AT91_PINCTRL_NONE>;
>> + };
>> +
>> + pinctrl_tcb0_tiob2: tcb0_tiob2-0 {
>> + atmel,pins = <AT91_PIOD 11
>> AT91_PERIPH_B AT91_PINCTRL_NONE>;
>> + };
>> + };
>> +
>> + pioA: gpio at fffff400 {
>> + compatible =
>> "atmel,at91rm9200-gpio";
>> + reg = <0xfffff400 0x200>;
>> + interrupts = <2
>> IRQ_TYPE_LEVEL_HIGH 1>;
>> + #gpio-cells = <2>;
>> + gpio-controller;
>> + interrupt-controller;
>> + #interrupt-cells = <2>;
>> + };
>> +
>> + pioB: gpio at fffff600 {
>> + compatible =
>> "atmel,at91rm9200-gpio";
>> + reg = <0xfffff600 0x200>;
>> + interrupts = <3
>> IRQ_TYPE_LEVEL_HIGH 1>;
>> + #gpio-cells = <2>;
>> + gpio-controller;
>> + interrupt-controller;
>> + #interrupt-cells = <2>;
>> + };
>> +
>> + pioC: gpio at fffff800 {
>> + compatible =
>> "atmel,at91rm9200-gpio";
>> + reg = <0xfffff800 0x200>;
>> + interrupts = <4
>> IRQ_TYPE_LEVEL_HIGH 1>;
>> + #gpio-cells = <2>;
>> + gpio-controller;
>> + interrupt-controller;
>> + #interrupt-cells = <2>;
>> + };
>> +
>> + pioD: gpio at fffffa00 {
>> + compatible =
>> "atmel,at91rm9200-gpio";
>> + reg = <0xfffffa00 0x200>;
>> + interrupts = <5
>> IRQ_TYPE_LEVEL_HIGH 1>;
>> + #gpio-cells = <2>;
>> + gpio-controller;
>> + interrupt-controller;
>> + #interrupt-cells = <2>;
>> + };
>> + };
>> +
>> + pmc: pmc at fffffc00 {
>> + compatible = "atmel,at91rm9200-pmc";
>> + reg = <0xfffffc00 0x100>;
>> + };
>> +
>> + rstc at fffffd00 {
>> + compatible = "atmel,at91sam9260-rstc";
>> + reg = <0xfffffd00 0x10>;
>> + };
>> +
>> + shdwc at fffffd10 {
>> + compatible = "atmel,at91sam9260-shdwc";
>> + reg = <0xfffffd10 0x10>;
>> + };
>> +
>> + pit: timer at fffffd30 {
>> + compatible = "atmel,at91sam9260-pit";
>> + reg = <0xfffffd30 0xf>;
>> + interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>;
>> + };
>> +
>> + watchdog at fffffd40 {
>> + compatible = "atmel,at91sam9260-wdt";
>> + reg = <0xfffffd40 0x10>;
>> + interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>;
>> + status = "disabled";
>> + };
>> + };
>> +
>> + nand0: nand at 40000000 {
>> + compatible = "atmel,at91rm9200-nand";
>> + #address-cells = <1>;
>> + #size-cells = <1>;
>> + reg = <0x40000000 0x10000000
>> + 0xffffe800 0x200
>> + >;
>> + atmel,nand-addr-offset = <21>;
>> + atmel,nand-cmd-offset = <22>;
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&pinctrl_nand>;
>> + gpios = <&pioD 17 GPIO_ACTIVE_HIGH
>> + &pioB 6 GPIO_ACTIVE_HIGH
>> + 0
>> + >;
>> + status = "disabled";
>> + };
>> + };
>> +
>> + i2c at 0 {
>> + compatible = "i2c-gpio";
>> + gpios = <&pioA 23 GPIO_ACTIVE_HIGH /* sda */
>> + &pioA 24 GPIO_ACTIVE_HIGH /* scl */
>> + >;
>> + i2c-gpio,sda-open-drain;
>> + i2c-gpio,scl-open-drain;
>> + i2c-gpio,delay-us = <2>; /* ~100 kHz */
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&pinctrl_i2c_gpio0>;
>> + status = "disabled";
>> + };
>> +
>> + i2c at 1 {
>> + compatible = "i2c-gpio";
>> + gpios = <&pioD 10 GPIO_ACTIVE_HIGH /* sda */
>> + &pioD 11 GPIO_ACTIVE_HIGH /* scl */
>> + >;
>> + i2c-gpio,sda-open-drain;
>> + i2c-gpio,scl-open-drain;
>> + i2c-gpio,delay-us = <2>; /* ~100 kHz */
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&pinctrl_i2c_gpio1>;
>> + status = "disabled";
>> + };
>> +};
>> diff --git a/arch/arm/mach-at91/at91sam9rl.c
>> b/arch/arm/mach-at91/at91sam9rl.c
>> index 3651517abedf..d6ee8bb47213 100644
>> --- a/arch/arm/mach-at91/at91sam9rl.c
>> +++ b/arch/arm/mach-at91/at91sam9rl.c
>
>
> I would have splitted this patch in 2 different patches:
> 1) define at91sam9rl DT clock lookup entries
> 2) add at91sam9rl DT SoC support
>
>
>> @@ -196,6 +196,22 @@ static struct clk_lookup periph_clocks_lookups[] = {
>> CLKDEV_CON_ID("pioB", &pioB_clk),
>> CLKDEV_CON_ID("pioC", &pioC_clk),
>> CLKDEV_CON_ID("pioD", &pioD_clk),
>> + /* more lookup table for DT entries */
>> + CLKDEV_CON_DEV_ID("usart", "fffff200.serial", &mck),
>> + CLKDEV_CON_DEV_ID("usart", "fffb0000.serial", &usart0_clk),
>> + CLKDEV_CON_DEV_ID("usart", "ffffb400.serial", &usart1_clk),
>> + CLKDEV_CON_DEV_ID("usart", "ffffb800.serial", &usart2_clk),
>> + CLKDEV_CON_DEV_ID("usart", "ffffbc00.serial", &usart3_clk),
>> + CLKDEV_CON_DEV_ID("t0_clk", "fffa0000.timer", &tc0_clk),
>> + CLKDEV_CON_DEV_ID("t1_clk", "fffa0000.timer", &tc1_clk),
>> + CLKDEV_CON_DEV_ID("t2_clk", "fffa0000.timer", &tc2_clk),
>> + CLKDEV_CON_DEV_ID("mci_clk", "fffa4000.mmc", &mmc_clk),
>> + CLKDEV_CON_DEV_ID(NULL, "fffa8000.i2c", &twi0_clk),
>> + CLKDEV_CON_DEV_ID(NULL, "fffac000.i2c", &twi1_clk),
>> + CLKDEV_CON_DEV_ID(NULL, "fffff400.gpio", &pioA_clk),
>> + CLKDEV_CON_DEV_ID(NULL, "fffff600.gpio", &pioB_clk),
>> + CLKDEV_CON_DEV_ID(NULL, "fffff800.gpio", &pioC_clk),
>> + CLKDEV_CON_DEV_ID(NULL, "fffffa00.gpio", &pioD_clk),
>> };
>> static struct clk_lookup usart_clocks_lookups[] = {
>
>
>
> _______________________________________________
> linux-arm-kernel mailing list
> linux-arm-kernel at lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
More information about the linux-arm-kernel
mailing list