pci-mvebu driver on km_kirkwood

[Thomas Petazzoni]

Dear Gerlando Falauto,

On Tue, 18 Feb 2014 18:29:56 +0100, Gerlando Falauto wrote:

> I tried these settings (a long time ago) and everything seemed to work 
> fine. Except, we now have a different problem.
> Essentially, this device requires 128MB for a given BAR to provide a 
> PCI-to-localbus bridge. (another BAR provides the configuration space to 
> configure chip select regions and so on).
> Apparently, only the first 64MB of this BAR seem to work correctly with 
> the new driver. As soon as you exceed that, reads (always?) return 0.
> Other BARs (which are then of course assigned a higher region) seem to 
> work just fine, so it looks like a per-BAR limitation.
> 
> This was not a problem with a 3.0 kernel. Do you have any idea what 
> could be wrong here?
> I'm currently using a 3.10 kernel, where your patches for the pci-mvebu 
> driver were forcibly brought in (without full support for the MBUS 
> description at device tree level though).

[...]

> mvebu-pcie pcie-controller.1: PCIe0.0: link up
> mvebu-pcie pcie-controller.1: PCI host bridge to bus 0000:00
> pci_bus 0000:00: root bus resource [io  0x1000-0xfffff]
> pci_bus 0000:00: root bus resource [mem 0xe0000000-0xefffffff]
> pci_bus 0000:00: root bus resource [bus 00-ff]
> pci 0000:00:01.0: [11ab:7846] type 01 class 0x060400
> PCI: bus0: Fast back to back transfers disabled
> pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring
> pci 0000:01:00.0: [10ee:0008] type 00 class 0x050000
> pci 0000:01:00.0: reg 10: [mem 0x00000000-0x00000fff]
> pci 0000:01:00.0: reg 14: [mem 0x00000000-0x07ffffff]
> pci 0000:01:00.0: reg 18: [mem 0x00000000-0x00000fff]
> pci 0000:01:00.0: reg 1c: [mem 0x00000000-0x007fffff]
> pci 0000:01:00.0: reg 20: [mem 0x00000000-0x00001fff]
> pci 0000:01:00.0: reg 24: [mem 0x00000000-0x00000fff]
> pci 0000:01:00.0: supports D1 D2
> pci 0000:01:00.0: PME# supported from D0 D1 D2 D3hot
> PCI: bus1: Fast back to back transfers disabled
> pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01
> pci 0000:00:01.0: BAR 8: assigned [mem 0xe0000000-0xebffffff]
> pci 0000:01:00.0: BAR 1: assigned [mem 0xe0000000-0xe7ffffff]

So I guess this one is the 128 MB BAR, right?

> pci 0000:01:00.0: BAR 3: assigned [mem 0xe8000000-0xe87fffff]
> pci 0000:01:00.0: BAR 4: assigned [mem 0xe8800000-0xe8801fff]
> pci 0000:01:00.0: BAR 0: assigned [mem 0xe8802000-0xe8802fff]
> pci 0000:01:00.0: BAR 2: assigned [mem 0xe8803000-0xe8803fff]
> pci 0000:01:00.0: BAR 5: assigned [mem 0xe8804000-0xe8804fff]

So in total, for the device 0000:01:00, the memory region should go
from 0xe0000000 to 0xe8804fff. This means that a 256 MB window is
needed for this device, because only power of two sizes are possible
for MBus windows.

Can you give me the output of /sys/kernel/debug/mvebu-mbus/devices ? It
will tell us how the MBus windows are configured, as I suspect the
problem might be here.

Thanks!

Thomas
-- 
Thomas Petazzoni, CTO, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com