[PATCH v2 00/12] Samsung PM consolidation part 2 (multiplatform)

[Tomasz Figa]

On 06.02.2014 20:12, Tomasz Figa wrote:
> Current Samsung PM code is heavily unprepared for multiplatform systems.
> The design implies accessing functions and global variables defined in
> particular mach- subdirectory from common code in plat-, which is not
> allowed when building ARCH_MULTIPLATFORM. In addition there is a lot of
> forced code unification, which makes common function handle any possible
> quirks of all supported SoCs. In the end this design turned out to not
> work too well, ending with a lot of empty functions exported from mach-,
> just because code in common pm.c calls them. Moreover, recent trend of
> moving lower level suspend/resume code to proper drivers, like pinctrl
> or clk, made a lot of code there redundant, especially on DT-only platforms
> like Exynos.
>
> This patch series attempts to untie Exynos PM support from the legacy
> Samsung PM core and make it multiplatform-aware, by isolating truly
> generic parts of the latter, making them multiplatform-friendly and then
> reimplementing Exynos PM support in a multiplatform-capable way by using
> those generic parts. The result is that now PM initialization is started
> from mach-exynos*-dt, which calls Exynos-specific initialization code that
> registers platform_suspend_ops, so control flow is basically reversed
> ending with mach- code calling more generic plat- code if needed.
>
> This is limited to Exynos right now, but remaining SoCs could follow
> in further series.
>
> Depends on Samsung PM consolidation part 1 (clocks) series:
>   - http://thread.gmane.org/gmane.linux.kernel.samsung-soc/26816
>
> On Exynos4210-based Trats, Exynos4412-based Trats2 and Exynos5250-based
> Arndale boards (except suspend/resume, which is broken because of
> unrelated reasons):
>
> Tested-by: Tomasz Figa <t.figa at samsung.com>
>
> Changes since v1 (RFC):
>   - fixed l2x0 resume,
>   - fixed checkpatch complaints (about issues in existing code being moved),
>   - rebased on top of current linux-next,
>   - slightly reordered patches to make the order more logical.
>
> Tomasz Figa (12):
>    ARM: EXYNOS: Do not resume l2x0 if not enabled before suspend
>    ARM: SAMSUNG: Add soc_is_s3c2410() helper
>    ARM: SAMSUNG: pm: Save UART DIVSLOT register based on SoC type
>    ARM: SAMSUNG: pm: Use debug_ll_addr() to get UART base address
>    ARM: SAMSUNG: pm: Consolidate PM debug functions
>    ARM: SAMSUNG: pm: Move Samsung PM debug code into separate file
>    ARM: SAMSUNG: Move common save/restore helpers to separate file
>    ARM: SAMSUNG: pm: Move s3c_pm_check_* prototypes to plat/pm-common.h
>    ARM: EXYNOS: Kconfig: Fix abuse of CONFIG_PM
>    ARM: EXYNOS: Remove PM initcalls and useless indirection
>    ARM: EXYNOS: Stop using legacy Samsung PM code
>    ARM: exynos: Allow wake-up using GIC interrupts
>
>   arch/arm/mach-exynos/Kconfig                   |  16 +--
>   arch/arm/mach-exynos/Makefile                  |   2 +-
>   arch/arm/mach-exynos/common.c                  |   1 +
>   arch/arm/mach-exynos/common.h                  |  14 ++
>   arch/arm/mach-exynos/include/mach/pm-core.h    |  75 -----------
>   arch/arm/mach-exynos/pm.c                      | 172 +++++++++++++++++++------
>   arch/arm/mach-exynos/regs-pmu.h                |   2 +
>   arch/arm/mach-exynos/sleep.S                   |  85 ++++++++++++
>   arch/arm/mach-s3c64xx/pm.c                     |   1 -
>   arch/arm/mach-s5p64x0/pm.c                     |   1 -
>   arch/arm/plat-samsung/Makefile                 |   2 +
>   arch/arm/plat-samsung/include/plat/cpu.h       |   6 +
>   arch/arm/plat-samsung/include/plat/pm-common.h | 110 ++++++++++++++++
>   arch/arm/plat-samsung/include/plat/pm.h        |  80 +-----------
>   arch/arm/plat-samsung/pm-check.c               |   2 +-
>   arch/arm/plat-samsung/pm-common.c              |  75 +++++++++++
>   arch/arm/plat-samsung/pm-debug.c               |  98 ++++++++++++++
>   arch/arm/plat-samsung/pm.c                     | 146 ---------------------
>   arch/arm/plat-samsung/s5p-sleep.S              |  43 -------
>   19 files changed, 531 insertions(+), 400 deletions(-)
>   delete mode 100644 arch/arm/mach-exynos/include/mach/pm-core.h
>   create mode 100644 arch/arm/mach-exynos/sleep.S
>   create mode 100644 arch/arm/plat-samsung/include/plat/pm-common.h
>   create mode 100644 arch/arm/plat-samsung/pm-common.c
>   create mode 100644 arch/arm/plat-samsung/pm-debug.c
>

With patch

[PATCH] ARM: dts: exynos5250-arndale: Keep G3D regulator always on

on Exynos5250-based Arndale board, including suspend to RAM:

Tested-by: Tomasz Figa <t.figa at samsung.com>

Best regards,
Tomasz