[PATCH v6 05/19] watchdog: orion: Make sure the watchdog is initially stopped

[Ezequiel Garcia]

On Mon, Feb 10, 2014 at 10:48:50AM -0600, linux at roeck-us.net wrote:
> Quoting Ezequiel Garcia <ezequiel.garcia at free-electrons.com>:
> 
> > On Fri, Feb 07, 2014 at 10:43:14AM -0700, Jason Gunthorpe wrote:
> >> On Fri, Feb 07, 2014 at 07:40:45AM -0300, Ezequiel Garcia wrote:
> >>
> >> > Well, this is related to the discussion about the bootloader not
> >> > reseting the watchdog properly, provoking spurious watchdog triggering.
> >> >
> >> > Jason Gunthorpe explained [1] that we needed a particular sequence:
> >> >
> >> >  1. Disable WDT
> >> >  2. Clear bridge
> >> >  3. Enable WDT
> >> >
> >> > We added the irq handling to satisfy (2), and the watchdog stop for (1).
> >>
> >> The issue here is the driver configures two 'machine kill' elements:
> >> the PANIC IRQ and the RstOut setup.
> >>
> >> Before configuring either of those the driver needs to ensure that any
> >> old watchdog events are cleared out of the HW. We must not get a
> >> spurious event.
> >>
> >> I agree not disabling an already functional and properly configured
> >> counter from the bootloader is desirable.
> >>
> >> So lets break it down a bit..
> >>
> >> 1) The IRQ:
> >>   It looks like the cause bit latches high on watchdog timer
> >>   expiration but has no side effect unless it is unmasked.
> >>
> >>   The new IRQ flow code ensures the bit is cleared during request_irq
> >>   so no old events can trigger the IRQ. Thus it is solved now.
> >>
> >
> > Agreed.
> >
> >> 3) The timer itself:
> >>   The WDT is just a general timer with an optional hookup to the
> >>   rst control. If it is harmlessly counting but not resetting we need
> >>   to stop that before enabling rst out.
> >>
> >
> > Actually, the current flow is to:
> >
> > 1. Disable rst out and then disable the counter, in probe().
> >
> > 2. Enable the counter, and then enable rst out, in start().
> >
> >> So, how about this for psuedo-code in probe:
> >>
> >> if (readl(RSTOUTn) & WDRstOutEn)
> >> {
> >>     /* Watchdog is configured and may be down counting,
> >>        don't touch it */
> >>     request_irq(..);
> >> }
> >> else
> >> {
> >>     /* Watchdog is not configured, fully disable the timer
> >>        and configure for watchdog operation. */
> >>     disable_watchdog();
> >>     request_irq();
> >>     writel(RSTOUTn), .. WDRstOutEn);
> >> }
> >>
> >
> > Sounds good, although it seems to me it's actually simpler:
> >
> >   /* Let's make sure the watchdog is fully stopped, unless
> >    * it's explicitly enabled and running
> >    */
> >   if ( !(wdt_rst_out_en && wdt_timer_enabled) ) {
> >     watchdog_stop();
> >   }
> >
> 
>      if (!wdt_rst_out_en || !wdt_timer_enabled)
>          watchdog_stop();
> 
> seems to be a bit easier to understand.
> 

Yeah, I was actually planning to have a orion_wdt_enabled() function
to get the running and enabled status. Looks cleaner I think.

	if (!orion_wdt_enabled())
		watchdog_stop();

So the idea is OK?

I'll push the new series in a short while. Unfortunately, this change
means I have to rebase almost all the series, because I introduce the
orion watchdog struct :-(
-- 
Ezequiel García, Free Electrons
Embedded Linux, Kernel and Android Engineering
http://free-electrons.com