[PATCH v3 01/15] at91: dt: Add at91sam9261 dt SoC support
Boris BREZILLON
b.brezillon at overkiz.com
Fri Feb 7 03:43:42 EST 2014
Hello Jean-Christophe,
On 07/02/2014 09:23, Jean-Christophe PLAGNIOL-VILLARD wrote:
> On 16:57 Thu 23 Jan , Jean-Jacques Hiblot wrote:
>> This patch adds the basics to support the Device Tree on a sam9261-based platform
>>
>> Signed-off-by: Jean-Jacques Hiblot <jjhiblot at traphandler.com>
>> ---
>> arch/arm/boot/dts/at91sam9261.dtsi | 627 +++++++++++++++++++++++++++++++++++++
>> arch/arm/mach-at91/at91sam9261.c | 15 +
>> 2 files changed, 642 insertions(+)
>> create mode 100644 arch/arm/boot/dts/at91sam9261.dtsi
>>
>> diff --git a/arch/arm/boot/dts/at91sam9261.dtsi b/arch/arm/boot/dts/at91sam9261.dtsi
>> new file mode 100644
>> index 0000000..2730611
>> --- /dev/null
>> +++ b/arch/arm/boot/dts/at91sam9261.dtsi
>> @@ -0,0 +1,627 @@
>> +/*
>> + * at91sam9261.dtsi - Device Tree Include file for AT91SAM9261 SoC
>> + *
>> + * Copyright (C) 2013 Jean-Jacques Hiblot <jjhiblot at traphandler.com>
>> + *
>> + * Licensed under GPLv2 only.
>> + */
>> +
>> +#include "skeleton.dtsi"
>> +#include <dt-bindings/pinctrl/at91.h>
>> +#include <dt-bindings/interrupt-controller/irq.h>
>> +#include <dt-bindings/gpio/gpio.h>
>> +#include <dt-bindings/clk/at91.h>
>> +
>> +/ {
>> + model = "Atmel AT91SAM9261 family SoC";
>> + compatible = "atmel,at91sam9261";
>> + interrupt-parent = <&aic>;
>> +
>> + aliases {
>> + serial0 = &dbgu;
>> + serial1 = &usart0;
>> + serial2 = &usart1;
>> + serial3 = &usart2;
>> + gpio0 = &pioA;
>> + gpio1 = &pioB;
>> + gpio2 = &pioC;
>> + tcb0 = &tcb0;
>> + i2c0 = &i2c0;
>> + ssc0 = &ssc0;
>> + ssc1 = &ssc1;
>> + };
>> + cpus {
>> + #address-cells = <0>;
>> + #size-cells = <0>;
>> +
>> + cpu {
>> + compatible = "arm,arm926ej-s";
>> + device_type = "cpu";
>> + };
>> + };
>> +
>> + memory {
>> + reg = <0x20000000 0x08000000>;
>> + };
>> +
>> + ahb {
>> + compatible = "simple-bus";
>> + #address-cells = <1>;
>> + #size-cells = <1>;
>> + ranges;
>> +
>> + usb0: ohci at 00500000 {
>> + compatible = "atmel,at91rm9200-ohci", "usb-ohci";
>> + reg = <0x00500000 0x100000>;
>> + interrupts = <20 IRQ_TYPE_LEVEL_HIGH 2>;
> as requested before use the new interrupt property
> interrupts-extended (mandatory)
>
> there is missing
> pinctrl-names = "default";
>
> on mmc & co
>> + status = "disabled";
>> + };
>> +
>> + nand0: nand at 40000000 {
>> + compatible = "atmel,at91rm9200-nand";
>> + #address-cells = <1>;
>> + #size-cells = <1>;
>> + reg = <0x40000000 0x10000000>;
>> + atmel,nand-addr-offset = <22>;
>> + atmel,nand-cmd-offset = <21>;
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&pinctrl_nand>;
>> +
>> + gpios = <&pioC 15 GPIO_ACTIVE_HIGH
>> + &pioC 14 GPIO_ACTIVE_HIGH
>> + 0
>> + >;
>> + status = "disabled";
>> + };
>> +
>> + apb {
>> + compatible = "simple-bus";
>> + #address-cells = <1>;
>> + #size-cells = <1>;
>> + ranges;
>> +
>> + tcb0: timer at fffa0000 {
>> + compatible = "atmel,at91rm9200-tcb";
>> + reg = <0xfffa0000 0x100>;
>> + interrupts = < 17 IRQ_TYPE_LEVEL_HIGH 0
>> + 18 IRQ_TYPE_LEVEL_HIGH 0
>> + 19 IRQ_TYPE_LEVEL_HIGH 0
>> + >;
>> + clocks = <&tcb0_clk>;
>> + clock-names = "t0_clk";
>> + status = "disabled";
> we use the tcb as shedule clock this should be on by default
>> + };
>> +
>> + usb1: gadget at fffa4000 {
>> + compatible = "atmel,at91rm9200-udc";
>> + reg = <0xfffa4000 0x4000>;
>> + interrupts = <10 IRQ_TYPE_LEVEL_HIGH 2>;
>> + status = "disabled";
>> + };
>> +
>> + mmc0: mmc at fffa8000 {
>> + compatible = "atmel,hsmci";
>> + reg = <0xfffa8000 0x600>;
>> + interrupts = <9 IRQ_TYPE_LEVEL_HIGH 0>;
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> + clocks = <&mci0_clk>;
>> + clock-names = "mci_clk";
>> + status = "disabled";
>> + };
>> +
>> + i2c0: i2c at fffac000 {
>> + compatible = "atmel,at91sam9261-i2c";
>> + pinctrl-0 = <&pinctrl_i2c_twi>;
>> + reg = <0xfffac000 0x100>;
>> + interrupts = <11 IRQ_TYPE_LEVEL_HIGH 6>;
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> + clocks = <&twi0_clk>;
>> + status = "disabled";
>> + };
>> +
>> + usart0: serial at fffb0000 {
>> + compatible = "atmel,at91sam9260-usart";
>> + reg = <0xfffb0000 0x200>;
>> + interrupts = <6 IRQ_TYPE_LEVEL_HIGH 5>;
>> + atmel,use-dma-rx;
>> + atmel,use-dma-tx;
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&pinctrl_usart0>;
>> + clocks = <&usart0_clk>;
>> + clock-names = "usart";
>> + status = "disabled";
>> + };
>> +
>> + usart1: serial at fffb4000 {
>> + compatible = "atmel,at91sam9260-usart";
>> + reg = <0xfffb4000 0x200>;
>> + interrupts = <7 IRQ_TYPE_LEVEL_HIGH 5>;
>> + atmel,use-dma-rx;
>> + atmel,use-dma-tx;
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&pinctrl_usart1>;
>> + clocks = <&usart1_clk>;
>> + clock-names = "usart";
>> + status = "disabled";
>> + };
>> +
>> + usart2: serial at fffb8000{
>> + compatible = "atmel,at91sam9260-usart";
>> + reg = <0xfffb8000 0x200>;
>> + interrupts = <8 IRQ_TYPE_LEVEL_HIGH 5>;
>> + atmel,use-dma-rx;
>> + atmel,use-dma-tx;
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&pinctrl_usart2>;
>> + clocks = <&usart2_clk>;
>> + clock-names = "usart";
>> + status = "disabled";
>> + };
>> +
>> + ssc0: ssc at fffbc000 {
>> + compatible = "atmel,at91rm9200-ssc";
>> + reg = <0xfffbc000 0x4000>;
>> + interrupts = <14 IRQ_TYPE_LEVEL_HIGH 5>;
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&pinctrl_ssc0_tx &pinctrl_ssc0_rx>;
>> + status = "disabled";
>> + };
>> +
>> + ssc1: ssc at fffc0000 {
>> + compatible = "atmel,at91rm9200-ssc";
>> + reg = <0xfffc0000 0x4000>;
>> + interrupts = <15 IRQ_TYPE_LEVEL_HIGH 5>;
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&pinctrl_ssc1_tx &pinctrl_ssc1_rx>;
>> + status = "disabled";
>> + };
>> +
>> + spi0: spi at fffc8000 {
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> + compatible = "atmel,at91rm9200-spi";
>> + reg = <0xfffc8000 0x200>;
>> + interrupts = <12 IRQ_TYPE_LEVEL_HIGH 3>;
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&pinctrl_spi0>;
>> + clocks = <&spi0_clk>;
>> + clock-names = "spi_clk";
>> + status = "disabled";
>> + };
>> +
>> + spi1: spi at fffcc000 {
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> + compatible = "atmel,at91rm9200-spi";
>> + reg = <0xfffcc000 0x200>;
>> + interrupts = <13 IRQ_TYPE_LEVEL_HIGH 3>;
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&pinctrl_spi1>;
>> + clocks = <&spi1_clk>;
>> + clock-names = "spi_clk";
>> + status = "disabled";
>> + };
> as said for sama5d3 we need to have macro for the hw CS as GPIO to make it
> more clear to use and read
>> +
>> + ramc: ramc at ffffea00 {
>> + compatible = "atmel,at91sam9260-sdramc";
>> + reg = <0xffffea00 0x200>;
>> + };
>> +
>> + aic: interrupt-controller at fffff000 {
>> + #interrupt-cells = <3>;
>> + compatible = "atmel,at91rm9200-aic";
>> + interrupt-controller;
>> + reg = <0xfffff000 0x200>;
>> + atmel,external-irqs = <29 30 31>;
>> + };
> one missing empty line
>> + dbgu: serial at fffff200 {
>> + compatible = "atmel,at91sam9260-usart";
>> + reg = <0xfffff200 0x200>;
>> + interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>;
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&pinctrl_dbgu>;
>> + clocks = <&mck>;
>> + clock-names = "usart";
>> + status = "disabled";
>> + };
>> +
>> + pinctrl at fffff400 {
>> + #address-cells = <1>;
>> + #size-cells = <1>;
>> + compatible = "atmel,at91rm9200-pinctrl", "simple-bus";
>> + ranges = <0xfffff400 0xfffff400 0xa00>;
>> +
>> + atmel,mux-mask = <
>> + /* A B */
>> + 0xffffffff 0xfffffff7 /* pioA */
>> + 0xffffffff 0xfffffff4 /* pioB */
>> + 0xffffffff 0xffffff07 /* pioC */
>> + >;
>> +
>> + /* shared pinctrl settings */
>> + dbgu {
>> + pinctrl_dbgu: dbgu-0 {
>> + atmel,pins =
>> + <AT91_PIOA 9 AT91_PERIPH_A AT91_PINCTRL_NONE
>> + AT91_PIOA 10 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>;
>> + };
>> + };
>> +
>> + usart0 {
>> + pinctrl_usart0: usart0-0 {
>> + atmel,pins =
>> + <AT91_PIOC 8 AT91_PERIPH_A AT91_PINCTRL_PULL_UP
>> + AT91_PIOC 9 AT91_PERIPH_A AT91_PINCTRL_NONE>;
>> + };
>> +
>> + pinctrl_usart0_rts: usart0_rts-0 {
>> + atmel,pins =
>> + <AT91_PIOC 10 AT91_PERIPH_A AT91_PINCTRL_NONE>;
>> + };
>> +
>> + pinctrl_usart0_cts: usart0_cts-0 {
>> + atmel,pins =
>> + <AT91_PIOC 11 AT91_PERIPH_A AT91_PINCTRL_NONE>;
>> + };
>> + };
>> +
>> + usart1 {
>> + pinctrl_usart1: usart1-0 {
>> + atmel,pins =
>> + <AT91_PIOC 12 AT91_PERIPH_A AT91_PINCTRL_PULL_UP
>> + AT91_PIOC 13 AT91_PERIPH_A AT91_PINCTRL_NONE>;
>> + };
>> +
>> + pinctrl_usart1_rts: usart1_rts-0 {
>> + atmel,pins =
>> + <AT91_PIOA 12 AT91_PERIPH_B AT91_PINCTRL_NONE>;
>> + };
>> +
>> + pinctrl_usart1_cts: usart1_cts-0 {
>> + atmel,pins =
>> + <AT91_PIOA 13 AT91_PERIPH_B AT91_PINCTRL_NONE>;
>> + };
>> + };
>> +
>> + usart2 {
>> + pinctrl_usart2: usart2-0 {
>> + atmel,pins =
>> + <AT91_PIOC 14 AT91_PERIPH_A AT91_PINCTRL_PULL_UP
>> + AT91_PIOC 15 AT91_PERIPH_A AT91_PINCTRL_NONE>;
>> + };
>> +
>> + pinctrl_usart2_rts: usart2_rts-0 {
>> + atmel,pins =
>> + <AT91_PIOA 15 AT91_PERIPH_B AT91_PINCTRL_NONE>;
>> + };
>> +
>> + pinctrl_usart2_cts: usart2_cts-0 {
>> + atmel,pins =
>> + <AT91_PIOA 16 AT91_PERIPH_B AT91_PINCTRL_NONE>;
>> + };
>> + };
>> +
>> + nand {
>> + pinctrl_nand: nand-0 {
>> + atmel,pins =
>> + <AT91_PIOC 15 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP
>> + AT91_PIOC 14 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP>;
>> + };
>> + };
>> +
>> + mmc0 {
>> + pinctrl_mmc0_clk: mmc0_clk-0 {
>> + atmel,pins =
>> + <AT91_PIOA 2 AT91_PERIPH_B AT91_PINCTRL_NONE>;
>> + };
>> +
>> + pinctrl_mmc0_slot0_cmd_dat0: mmc0_slot0_cmd_dat0-0 {
>> + atmel,pins =
>> + <AT91_PIOA 1 AT91_PERIPH_B AT91_PINCTRL_PULL_UP
>> + AT91_PIOA 0 AT91_PERIPH_B AT91_PINCTRL_PULL_UP>;
>> + };
>> +
>> + pinctrl_mmc0_slot0_dat1_3: mmc0_slot0_dat1_3-0 {
>> + atmel,pins =
>> + <AT91_PIOA 4 AT91_PERIPH_B AT91_PINCTRL_PULL_UP
>> + AT91_PIOA 5 AT91_PERIPH_B AT91_PINCTRL_PULL_UP
>> + AT91_PIOA 6 AT91_PERIPH_B AT91_PINCTRL_PULL_UP>;
>> + };
>> + };
>> +
>> + ssc0 {
>> + pinctrl_ssc0_tx: ssc0_tx-0 {
>> + atmel,pins =
>> + <AT91_PIOB 21 AT91_PERIPH_A AT91_PINCTRL_NONE
>> + AT91_PIOB 22 AT91_PERIPH_A AT91_PINCTRL_NONE
>> + AT91_PIOB 23 AT91_PERIPH_A AT91_PINCTRL_NONE>;
>> + };
>> +
>> + pinctrl_ssc0_rx: ssc0_rx-0 {
>> + atmel,pins =
>> + <AT91_PIOB 24 AT91_PERIPH_A AT91_PINCTRL_NONE
>> + AT91_PIOB 25 AT91_PERIPH_A AT91_PINCTRL_NONE
>> + AT91_PIOB 26 AT91_PERIPH_A AT91_PINCTRL_NONE>;
>> + };
>> + };
>> +
>> + ssc1 {
>> + pinctrl_ssc1_tx: ssc1_tx-0 {
>> + atmel,pins =
>> + <AT91_PIOA 17 AT91_PERIPH_B AT91_PINCTRL_NONE
>> + AT91_PIOA 18 AT91_PERIPH_B AT91_PINCTRL_NONE
>> + AT91_PIOA 19 AT91_PERIPH_B AT91_PINCTRL_NONE>;
>> + };
>> +
>> + pinctrl_ssc1_rx: ssc1_rx-0 {
>> + atmel,pins =
>> + <AT91_PIOA 20 AT91_PERIPH_B AT91_PINCTRL_NONE
>> + AT91_PIOA 21 AT91_PERIPH_B AT91_PINCTRL_NONE
>> + AT91_PIOA 22 AT91_PERIPH_B AT91_PINCTRL_NONE>;
>> + };
>> + };
>> +
>> + spi0 {
>> + pinctrl_spi0: spi0-0 {
>> + atmel,pins =
>> + <AT91_PIOA 0 AT91_PERIPH_A AT91_PINCTRL_NONE
>> + AT91_PIOA 1 AT91_PERIPH_A AT91_PINCTRL_NONE
>> + AT91_PIOA 2 AT91_PERIPH_A AT91_PINCTRL_NONE>;
>> + };
>> + };
>> +
>> + spi1 {
>> + pinctrl_spi1: spi1-0 {
>> + atmel,pins =
>> + <AT91_PIOB 30 AT91_PERIPH_A AT91_PINCTRL_NONE
>> + AT91_PIOB 31 AT91_PERIPH_A AT91_PINCTRL_NONE
>> + AT91_PIOB 29 AT91_PERIPH_A AT91_PINCTRL_NONE>;
>> + };
>> + };
>> +
>> + tcb0 {
>> + pinctrl_tcb0_tclk0: tcb0_tclk0-0 {
>> + atmel,pins = <AT91_PIOC 16 AT91_PERIPH_B AT91_PINCTRL_NONE>;
>> + };
>> +
>> + pinctrl_tcb0_tclk1: tcb0_tclk1-0 {
>> + atmel,pins = <AT91_PIOC 17 AT91_PERIPH_B AT91_PINCTRL_NONE>;
>> + };
>> +
>> + pinctrl_tcb0_tclk2: tcb0_tclk2-0 {
>> + atmel,pins = <AT91_PIOC 18 AT91_PERIPH_B AT91_PINCTRL_NONE>;
>> + };
>> +
>> + pinctrl_tcb0_tioa0: tcb0_tioa0-0 {
>> + atmel,pins = <AT91_PIOC 19 AT91_PERIPH_B AT91_PINCTRL_NONE>;
>> + };
>> +
>> + pinctrl_tcb0_tioa1: tcb0_tioa1-0 {
>> + atmel,pins = <AT91_PIOC 21 AT91_PERIPH_B AT91_PINCTRL_NONE>;
>> + };
>> +
>> + pinctrl_tcb0_tioa2: tcb0_tioa2-0 {
>> + atmel,pins = <AT91_PIOC 23 AT91_PERIPH_B AT91_PINCTRL_NONE>;
>> + };
>> +
>> + pinctrl_tcb0_tiob0: tcb0_tiob0-0 {
>> + atmel,pins = <AT91_PIOC 20 AT91_PERIPH_B AT91_PINCTRL_NONE>;
>> + };
>> +
>> + pinctrl_tcb0_tiob1: tcb0_tiob1-0 {
>> + atmel,pins = <AT91_PIOC 22 AT91_PERIPH_B AT91_PINCTRL_NONE>;
>> + };
>> +
>> + pinctrl_tcb0_tiob2: tcb0_tiob2-0 {
>> + atmel,pins = <AT91_PIOC 24 AT91_PERIPH_B AT91_PINCTRL_NONE>;
>> + };
>> + };
>> +
>> + i2c0 {
>> + pinctrl_i2c_bitbang: i2c-0-bitbang {
>> + atmel,pins =
>> + <AT91_PIOA 7 AT91_PERIPH_GPIO AT91_PINCTRL_NONE
>> + AT91_PIOA 8 AT91_PERIPH_GPIO AT91_PINCTRL_NONE>;
>> + };
>> + pinctrl_i2c_twi: i2c-0-twi {
>> + atmel,pins =
>> + <AT91_PIOA 7 AT91_PERIPH_A AT91_PINCTRL_NONE
>> + AT91_PIOA 8 AT91_PERIPH_A AT91_PINCTRL_NONE>;
>> + };
>> + };
>> +
>> + pioA: gpio at fffff400 {
>> + compatible = "atmel,at91rm9200-gpio";
>> + reg = <0xfffff400 0x200>;
>> + interrupts = <2 IRQ_TYPE_LEVEL_HIGH 1>;
>> + #gpio-cells = <2>;
>> + gpio-controller;
>> + interrupt-controller;
>> + #interrupt-cells = <2>;
>> + clocks = <&pioA_clk>;
>> + };
>> +
>> + pioB: gpio at fffff600 {
>> + compatible = "atmel,at91rm9200-gpio";
>> + reg = <0xfffff600 0x200>;
>> + interrupts = <3 IRQ_TYPE_LEVEL_HIGH 1>;
>> + #gpio-cells = <2>;
>> + gpio-controller;
>> + interrupt-controller;
>> + #interrupt-cells = <2>;
>> + clocks = <&pioB_clk>;
>> + };
>> +
>> + pioC: gpio at fffff800 {
>> + compatible = "atmel,at91rm9200-gpio";
>> + reg = <0xfffff800 0x200>;
>> + interrupts = <4 IRQ_TYPE_LEVEL_HIGH 1>;
>> + #gpio-cells = <2>;
>> + gpio-controller;
>> + interrupt-controller;
>> + #interrupt-cells = <2>;
>> + clocks = <&pioC_clk>;
>> + };
>> + };
>> +
>> + pmc: pmc at fffffc00 {
>> + compatible = "atmel,at91rm9200-pmc";
>> + reg = <0xfffffc00 0x100>;
>> + interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>;
>> + interrupt-controller;
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> + #interrupt-cells = <1>;
>> +
>> + clk32k: slck {
>> + compatible = "fixed-clock";
>> + #clock-cells = <0>;
>> + clock-frequency = <32768>;
>> + };
>> +
>> + main: mainck {
>> + compatible = "atmel,at91rm9200-clk-main";
>> + #clock-cells = <0>;
>> + interrupts-extended = <&pmc AT91_PMC_MOSCS>;
>> + clocks = <&clk32k>;
>> + };
>> +
>> + plla: pllack {
>> + compatible = "atmel,at91rm9200-clk-pll";
>> + #clock-cells = <0>;
>> + interrupts-extended = <&pmc AT91_PMC_LOCKA>;
>> + clocks = <&main>;
>> + reg = <0>;
>> + atmel,clk-input-range = <1000000 32000000>;
>> + #atmel,pll-clk-output-range-cells = <4>;
>> + atmel,pll-clk-output-ranges = <80000000 200000000 190000000 240000000>;
>> + };
>> +
>> + pllb: pllbck {
>> + compatible = "atmel,at91rm9200-clk-pll";
>> + #clock-cells = <0>;
>> + interrupts-extended = <&pmc AT91_PMC_LOCKB>;
>> + clocks = <&main>;
>> + reg = <1>;
>> + atmel,clk-input-range = <1000000 32000000>;
>> + #atmel,pll-clk-output-range-cells = <4>;
>> + atmel,pll-clk-output-ranges = <80000000 200000000 190000000 240000000>;
>> + };
>> +
>> + mck: masterck {
>> + compatible = "atmel,at91rm9200-clk-master";
>> + #clock-cells = <0>;
>> + interrupts-extended = <&pmc AT91_PMC_MCKRDY>;
>> + clocks = <&clk32k>, <&main>, <&plla>, <&pllb>;
>> + atmel,clk-output-range = <0 94000000>;
>> + atmel,clk-divisors = <1 2 4 3>;
>> + };
>> + periphck {
>> + compatible = "atmel,at91rm9200-clk-peripheral";
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> + clocks = <&mck>;
>> +
>> + pioA_clk: pioA_clk {
>> + #clock-cells = <0>;
>> + reg = <2>;
>> + };
>> +
>> + pioB_clk: pioB_clk {
>> + #clock-cells = <0>;
>> + reg = <3>;
>> + };
>> +
>> + pioC_clk: pioC_clk {
>> + #clock-cells = <0>;
>> + reg = <4>;
>> + };
>> +
>> + usart0_clk: usart0_clk {
>> + #clock-cells = <0>;
>> + reg = <6>;
>> + };
>> +
>> + usart1_clk: usart1_clk {
>> + #clock-cells = <0>;
>> + reg = <7>;
>> + };
>> +
>> + usart2_clk: usart2_clk {
>> + #clock-cells = <0>;
>> + reg = <8>;
>> + };
>> +
>> + mci0_clk: mci0_clk {
>> + #clock-cells = <0>;
>> + reg = <9>;
>> + };
>> +
>> + twi0_clk: twi0_clk {
>> + reg = <11>;
>> + #clock-cells = <0>;
>> + };
>> +
>> + spi0_clk: spi0_clk {
>> + #clock-cells = <0>;
>> + reg = <12>;
>> + };
>> +
>> + spi1_clk: spi1_clk {
>> + #clock-cells = <0>;
>> + reg = <13>;
>> + };
>> +
>> + tcb0_clk: tcb0_clk {
>> + #clock-cells = <0>;
>> + reg = <17>;
>> + };
>> +
>> + lcd_clk: lcd_clk {
>> + #clock-cells = <0>;
>> + reg = <21>;
>> + };
>> + };
>> + };
>> +
>> + rstc at fffffd00 {
>> + compatible = "atmel,at91sam9260-rstc";
>> + reg = <0xfffffd00 0x10>;
>> + };
>> +
>> + shdwc at fffffd10 {
>> + compatible = "atmel,at91sam9260-shdwc";
>> + reg = <0xfffffd10 0x10>;
>> + };
>> +
>> + pit: timer at fffffd30 {
>> + compatible = "atmel,at91sam9260-pit";
>> + reg = <0xfffffd30 0xf>;
>> + interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>;
>> + clocks = <&mck>;
>> + };
>> +
>> + watchdog at fffffd40 {
>> + compatible = "atmel,at91sam9260-wdt";
>> + reg = <0xfffffd40 0x10>;
>> + status = "disabled";
>> + };
>> + };
>> + };
>> +
>> + i2c at 0 {
>> + compatible = "i2c-gpio";
>> + pinctrl-0 = <&pinctrl_i2c_bitbang>;
>> + gpios = <&pioA 7 GPIO_ACTIVE_HIGH /* sda */
>> + &pioA 8 GPIO_ACTIVE_HIGH /* scl */
>> + >;
>> + i2c-gpio,sda-open-drain;
>> + i2c-gpio,scl-open-drain;
>> + i2c-gpio,delay-us = <2>; /* ~100 kHz */
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> + status = "disabled";
>> + };
>> +};
>> diff --git a/arch/arm/mach-at91/at91sam9261.c b/arch/arm/mach-at91/at91sam9261.c
>> index 6276b4c..6a2c869 100644
>> --- a/arch/arm/mach-at91/at91sam9261.c
>> +++ b/arch/arm/mach-at91/at91sam9261.c
>> @@ -189,6 +189,21 @@ static struct clk_lookup periph_clocks_lookups[] = {
>> CLKDEV_CON_ID("pioA", &pioA_clk),
>> CLKDEV_CON_ID("pioB", &pioB_clk),
>> CLKDEV_CON_ID("pioC", &pioC_clk),
>> + /* more usart lookup table for DT entries */
>> + CLKDEV_CON_DEV_ID("usart", "fffff200.serial", &mck),
>> + CLKDEV_CON_DEV_ID("usart", "fffb0000.serial", &usart0_clk),
>> + CLKDEV_CON_DEV_ID("usart", "ffffb400.serial", &usart1_clk),
>> + CLKDEV_CON_DEV_ID("usart", "fff94000.serial", &usart2_clk),
>> + /* more tc lookup table for DT entries */
>> + CLKDEV_CON_DEV_ID("t0_clk", "fffa0000.timer", &tc0_clk),
>> + CLKDEV_CON_DEV_ID("hclk", "500000.ohci", &hck0),
>> + CLKDEV_CON_DEV_ID("spi_clk", "fffc8000.spi", &spi0_clk),
>> + CLKDEV_CON_DEV_ID("spi_clk", "fffcc000.spi", &spi1_clk),
>> + CLKDEV_CON_DEV_ID("mci_clk", "fffa8000.mmc", &mmc_clk),
>> + CLKDEV_CON_DEV_ID(NULL, "fffac000.i2c", &twi_clk),
>> + CLKDEV_CON_DEV_ID(NULL, "fffff400.gpio", &pioA_clk),
>> + CLKDEV_CON_DEV_ID(NULL, "fffff600.gpio", &pioB_clk),
>> + CLKDEV_CON_DEV_ID(NULL, "fffff800.gpio", &pioC_clk),
> do we really need this with ccf?
We need this in case we want to support multi-board kernel with some boards
that do not support CCF.
If you want to drop these clk lookup defintions you'll have to add the
"depends on COMMON_CLK" line in the "config SOC_AT91SAM9261" section.
Best Regards,
Boris
>> };
>>
>> static struct clk_lookup usart_clocks_lookups[] = {
>> --
>> 1.8.5.2
>>
More information about the linux-arm-kernel
mailing list