[PATCH] can: xilinx CAN controller support.
Kedareswara rao Appana
appana.durga.rao at xilinx.com
Thu Feb 6 05:19:36 EST 2014
This patch adds xilinx CAN controller support.
This driver supports both ZYNQ CANPS IP and
Soft IP AXI CAN controller.
Signed-off-by: Kedareswara rao Appana <appanad at xilinx.com>
---
This patch is rebased on the 3.14 rc1 kernel.
---
.../devicetree/bindings/net/can/xilinx_can.txt | 43 +
drivers/net/can/Kconfig | 8 +
drivers/net/can/Makefile | 1 +
drivers/net/can/xilinx_can.c | 1150 ++++++++++++++++++++
4 files changed, 1202 insertions(+), 0 deletions(-)
create mode 100644 Documentation/devicetree/bindings/net/can/xilinx_can.txt
create mode 100644 drivers/net/can/xilinx_can.c
diff --git a/Documentation/devicetree/bindings/net/can/xilinx_can.txt b/Documentation/devicetree/bindings/net/can/xilinx_can.txt
new file mode 100644
index 0000000..34f9643
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/can/xilinx_can.txt
@@ -0,0 +1,43 @@
+Xilinx Axi CAN/Zynq CANPS controller Device Tree Bindings
+---------------------------------------------------------
+
+Required properties:
+- compatible : Should be "xlnx,zynq-can-1.00.a" for Zynq CAN
+ controllers and "xlnx,axi-can-1.00.a" for Axi CAN
+ controllers.
+- reg : Physical base address and size of the Axi CAN/Zynq
+ CANPS registers map.
+- interrupts : Property with a value describing the interrupt
+ number.
+- interrupt-parent : Must be core interrupt controller
+- clock-names : List of input clock names - "ref_clk", "aper_clk"
+ (See clock bindings for details. Two clocks are
+ required for Zynq CAN. For Axi CAN
+ case it is one(ref_clk)).
+- clocks : Clock phandles (see clock bindings for details).
+- xlnx,can-tx-dpth : Can Tx fifo depth (Required for Axi CAN).
+- xlnx,can-rx-dpth : Can Rx fifo depth (Required for Axi CAN).
+
+
+Example:
+
+For Zynq CANPS Dts file:
+ zynq_can_0: zynq-can at e0008000 {
+ compatible = "xlnx,zynq-can-1.00.a";
+ clocks = <&clkc 19>, <&clkc 36>;
+ clock-names = "ref_clk", "aper_clk";
+ reg = <0xe0008000 0x1000>;
+ interrupts = <0 28 4>;
+ interrupt-parent = <&intc>;
+ };
+For Axi CAN Dts file:
+ axi_can_0: axi-can at 40000000 {
+ compatible = "xlnx,axi-can-1.00.a";
+ clocks = <&clkc 0>;
+ clock-names = "ref_clk" ;
+ reg = <0x40000000 0x10000>;
+ interrupt-parent = <&intc>;
+ interrupts = <0 59 1>;
+ xlnx,can-tx-dpth = <0x40>;
+ xlnx,can-rx-dpth = <0x40>;
+ };
diff --git a/drivers/net/can/Kconfig b/drivers/net/can/Kconfig
index d447b88..2344fb5 100644
--- a/drivers/net/can/Kconfig
+++ b/drivers/net/can/Kconfig
@@ -125,6 +125,14 @@ config CAN_GRCAN
endian syntheses of the cores would need some modifications on
the hardware level to work.
+config CAN_XILINXCAN
+ tristate "Xilinx CAN"
+ depends on ARCH_ZYNQ || MICROBLAZE
+ default n
+ ---help---
+ Xilinx CAN driver. This driver supports both soft AXI CAN IP and
+ Zynq CANPS IP.
+
source "drivers/net/can/mscan/Kconfig"
source "drivers/net/can/sja1000/Kconfig"
diff --git a/drivers/net/can/Makefile b/drivers/net/can/Makefile
index c744039..0b8e11e 100644
--- a/drivers/net/can/Makefile
+++ b/drivers/net/can/Makefile
@@ -25,5 +25,6 @@ obj-$(CONFIG_CAN_JANZ_ICAN3) += janz-ican3.o
obj-$(CONFIG_CAN_FLEXCAN) += flexcan.o
obj-$(CONFIG_PCH_CAN) += pch_can.o
obj-$(CONFIG_CAN_GRCAN) += grcan.o
+obj-$(CONFIG_CAN_XILINXCAN) += xilinx_can.o
ccflags-$(CONFIG_CAN_DEBUG_DEVICES) := -DDEBUG
diff --git a/drivers/net/can/xilinx_can.c b/drivers/net/can/xilinx_can.c
new file mode 100644
index 0000000..c1b2b9d
--- /dev/null
+++ b/drivers/net/can/xilinx_can.c
@@ -0,0 +1,1150 @@
+/* Xilinx CAN device driver
+ *
+ * Copyright (C) 2012 - 2014 Xilinx, Inc.
+ * Copyright (C) 2009 PetaLogix. All rights reserved.
+ *
+ * Description:
+ * This driver is developed for Axi CAN IP and for Zynq CANPS Controller.
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program. If not, see <http://www.gnu.org/licenses/>.
+ */
+
+#include <linux/clk.h>
+#include <linux/errno.h>
+#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <linux/io.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/netdevice.h>
+#include <linux/of.h>
+#include <linux/platform_device.h>
+#include <linux/skbuff.h>
+#include <linux/string.h>
+#include <linux/types.h>
+#include <linux/can/dev.h>
+#include <linux/can/error.h>
+#include <linux/can/led.h>
+
+#define DRIVER_NAME "XILINX_CAN"
+
+/* CAN registers set */
+#define XCAN_SRR_OFFSET 0x00 /* Software reset */
+#define XCAN_MSR_OFFSET 0x04 /* Mode select */
+#define XCAN_BRPR_OFFSET 0x08 /* Baud rate prescaler */
+#define XCAN_BTR_OFFSET 0x0C /* Bit timing */
+#define XCAN_ECR_OFFSET 0x10 /* Error counter */
+#define XCAN_ESR_OFFSET 0x14 /* Error status */
+#define XCAN_SR_OFFSET 0x18 /* Status */
+#define XCAN_ISR_OFFSET 0x1C /* Interrupt status */
+#define XCAN_IER_OFFSET 0x20 /* Interrupt enable */
+#define XCAN_ICR_OFFSET 0x24 /* Interrupt clear */
+#define XCAN_TXFIFO_ID_OFFSET 0x30 /* TX FIFO ID */
+#define XCAN_TXFIFO_DLC_OFFSET 0x34 /* TX FIFO DLC */
+#define XCAN_TXFIFO_DW1_OFFSET 0x38 /* TX FIFO Data Word 1 */
+#define XCAN_TXFIFO_DW2_OFFSET 0x3C /* TX FIFO Data Word 2 */
+#define XCAN_RXFIFO_ID_OFFSET 0x50 /* RX FIFO ID */
+#define XCAN_RXFIFO_DLC_OFFSET 0x54 /* RX FIFO DLC */
+#define XCAN_RXFIFO_DW1_OFFSET 0x58 /* RX FIFO Data Word 1 */
+#define XCAN_RXFIFO_DW2_OFFSET 0x5C /* RX FIFO Data Word 2 */
+
+/* CAN register bit masks - XCAN_<REG>_<BIT>_MASK */
+#define XCAN_SRR_CEN_MASK 0x00000002 /* CAN enable */
+#define XCAN_SRR_RESET_MASK 0x00000001 /* Soft Reset the CAN core */
+#define XCAN_MSR_LBACK_MASK 0x00000002 /* Loop back mode select */
+#define XCAN_MSR_SLEEP_MASK 0x00000001 /* Sleep mode select */
+#define XCAN_BRPR_BRP_MASK 0x000000FF /* Baud rate prescaler */
+#define XCAN_BTR_SJW_MASK 0x00000180 /* Synchronous jump width */
+#define XCAN_BTR_TS2_MASK 0x00000070 /* Time segment 2 */
+#define XCAN_BTR_TS1_MASK 0x0000000F /* Time segment 1 */
+#define XCAN_ECR_REC_MASK 0x0000FF00 /* Receive error counter */
+#define XCAN_ECR_TEC_MASK 0x000000FF /* Transmit error counter */
+#define XCAN_ESR_ACKER_MASK 0x00000010 /* ACK error */
+#define XCAN_ESR_BERR_MASK 0x00000008 /* Bit error */
+#define XCAN_ESR_STER_MASK 0x00000004 /* Stuff error */
+#define XCAN_ESR_FMER_MASK 0x00000002 /* Form error */
+#define XCAN_ESR_CRCER_MASK 0x00000001 /* CRC error */
+#define XCAN_SR_TXFLL_MASK 0x00000400 /* TX FIFO is full */
+#define XCAN_SR_ESTAT_MASK 0x00000180 /* Error status */
+#define XCAN_SR_ERRWRN_MASK 0x00000040 /* Error warning */
+#define XCAN_SR_NORMAL_MASK 0x00000008 /* Normal mode */
+#define XCAN_SR_LBACK_MASK 0x00000002 /* Loop back mode */
+#define XCAN_SR_CONFIG_MASK 0x00000001 /* Configuration mode */
+#define XCAN_IXR_TXFEMP_MASK 0x00004000 /* TX FIFO Empty */
+#define XCAN_IXR_WKUP_MASK 0x00000800 /* Wake up interrupt */
+#define XCAN_IXR_SLP_MASK 0x00000400 /* Sleep interrupt */
+#define XCAN_IXR_BSOFF_MASK 0x00000200 /* Bus off interrupt */
+#define XCAN_IXR_ERROR_MASK 0x00000100 /* Error interrupt */
+#define XCAN_IXR_RXNEMP_MASK 0x00000080 /* RX FIFO NotEmpty intr */
+#define XCAN_IXR_RXOFLW_MASK 0x00000040 /* RX FIFO Overflow intr */
+#define XCAN_IXR_RXOK_MASK 0x00000010 /* Message received intr */
+#define XCAN_IXR_TXOK_MASK 0x00000002 /* TX successful intr */
+#define XCAN_IXR_ARBLST_MASK 0x00000001 /* Arbitration lost intr */
+#define XCAN_IDR_ID1_MASK 0xFFE00000 /* Standard msg identifier */
+#define XCAN_IDR_SRR_MASK 0x00100000 /* Substitute remote TXreq */
+#define XCAN_IDR_IDE_MASK 0x00080000 /* Identifier extension */
+#define XCAN_IDR_ID2_MASK 0x0007FFFE /* Extended message ident */
+#define XCAN_IDR_RTR_MASK 0x00000001 /* Remote TX request */
+#define XCAN_DLCR_DLC_MASK 0xF0000000 /* Data length code */
+
+#define XCAN_INTR_ALL (XCAN_IXR_TXOK_MASK | XCAN_IXR_BSOFF_MASK |\
+ XCAN_IXR_WKUP_MASK | XCAN_IXR_SLP_MASK | \
+ XCAN_IXR_RXNEMP_MASK | XCAN_IXR_ERROR_MASK | \
+ XCAN_IXR_ARBLST_MASK | XCAN_IXR_RXOK_MASK)
+
+/* CAN register bit shift - XCAN_<REG>_<BIT>_SHIFT */
+#define XCAN_BTR_SJW_SHIFT 7 /* Synchronous jump width */
+#define XCAN_BTR_TS2_SHIFT 4 /* Time segment 2 */
+#define XCAN_IDR_ID1_SHIFT 21 /* Standard Messg Identifier */
+#define XCAN_IDR_ID2_SHIFT 1 /* Extended Message Identifier */
+#define XCAN_DLCR_DLC_SHIFT 28 /* Data length code */
+#define XCAN_ESR_REC_SHIFT 8 /* Rx Error Count */
+
+/* CAN frame length constants */
+#define XCAN_ECHO_SKB_MAX 64
+#define XCAN_NAPI_WEIGHT 64
+#define XCAN_FRAME_MAX_DATA_LEN 8
+#define XCAN_TIMEOUT (50 * HZ)
+
+/**
+ * struct xcan_priv - This definition define CAN driver instance
+ * @can: CAN private data structure.
+ * @open_time: For holding timeout values
+ * @waiting_ech_skb_index: Pointer for skb
+ * @ech_skb_next: This tell the next packet in the queue
+ * @waiting_ech_skb_num: Gives the number of packets waiting
+ * @xcan_echo_skb_max_tx: Maximum number packets the driver can send
+ * @xcan_echo_skb_max_rx: Maximum number packets the driver can receive
+ * @napi: NAPI structure
+ * @ech_skb_lock: For spinlock purpose
+ * @read_reg: For reading data from CAN registers
+ * @write_reg: For writing data to CAN registers
+ * @dev: Network device data structure
+ * @reg_base: Ioremapped address to registers
+ * @irq_flags: For request_irq()
+ * @aperclk: Pointer to struct clk
+ * @devclk: Pointer to struct clk
+ */
+struct xcan_priv {
+ struct can_priv can;
+ int open_time;
+ int waiting_ech_skb_index;
+ int ech_skb_next;
+ int waiting_ech_skb_num;
+ int xcan_echo_skb_max_tx;
+ int xcan_echo_skb_max_rx;
+ struct napi_struct napi;
+ spinlock_t ech_skb_lock;
+ u32 (*read_reg)(const struct xcan_priv *priv, int reg);
+ void (*write_reg)(const struct xcan_priv *priv, int reg, u32 val);
+ struct net_device *dev;
+ void __iomem *reg_base;
+ unsigned long irq_flags;
+ struct clk *aperclk;
+ struct clk *devclk;
+};
+
+/* CAN Bittiming constants as per Xilinx CAN specs */
+static struct can_bittiming_const xcan_bittiming_const = {
+ .name = DRIVER_NAME,
+ .tseg1_min = 1,
+ .tseg1_max = 16,
+ .tseg2_min = 1,
+ .tseg2_max = 8,
+ .sjw_max = 4,
+ .brp_min = 1,
+ .brp_max = 256,
+ .brp_inc = 1,
+};
+
+/**
+ * xcan_write_reg - Write a value to the device register
+ * @priv: Driver private data structure
+ * @reg: Register offset
+ * @val: Value to write at the Register offset
+ *
+ * Write data to the paricular CAN register
+ */
+static void xcan_write_reg(const struct xcan_priv *priv, int reg, u32 val)
+{
+ writel(val, priv->reg_base + reg);
+}
+
+/**
+ * xcan_read_reg - Read a value from the device register
+ * @priv: Driver private data structure
+ * @reg: Register offset
+ *
+ * Read data from the particular CAN register
+ * Return: value read from the CAN register
+ */
+static u32 xcan_read_reg(const struct xcan_priv *priv, int reg)
+{
+ return readl(priv->reg_base + reg);
+}
+
+/**
+ * set_reset_mode - Resets the CAN device mode
+ * @ndev: Pointer to net_device structure
+ *
+ * This is the driver reset mode routine.The driver
+ * enters into configuration mode.
+ *
+ * Return: 0 on success and failure value on error
+ */
+static int set_reset_mode(struct net_device *ndev)
+{
+ struct xcan_priv *priv = netdev_priv(ndev);
+ unsigned long timeout;
+
+ priv->can.state = CAN_STATE_STOPPED;
+ priv->write_reg(priv, XCAN_SRR_OFFSET, XCAN_SRR_OFFSET);
+
+ timeout = jiffies + XCAN_TIMEOUT;
+ while (!(priv->read_reg(priv, XCAN_SR_OFFSET) & XCAN_SR_CONFIG_MASK)) {
+ if (time_after(jiffies, timeout)) {
+ netdev_warn(ndev, "timedout waiting for config mode\n");
+ return -ETIMEDOUT;
+ }
+ schedule_timeout(1);
+ }
+
+ return 0;
+}
+
+/**
+ * xcan_set_bittiming - CAN set bit timing routine
+ * @ndev: Pointer to net_device structure
+ *
+ * This is the driver set bittiming routine.
+ * Return: 0 on success and failure value on error
+ */
+static int xcan_set_bittiming(struct net_device *ndev)
+{
+ struct xcan_priv *priv = netdev_priv(ndev);
+ struct can_bittiming *bt = &priv->can.bittiming;
+ u32 btr0, btr1;
+ u32 is_config_mode;
+
+ /* Check whether Xilinx CAN is in configuration mode.
+ * It cannot set bit timing if Xilinx CAN is not in configuration mode.
+ */
+ is_config_mode = priv->read_reg(priv, XCAN_SR_OFFSET) &
+ XCAN_SR_CONFIG_MASK;
+ if (!is_config_mode) {
+ netdev_alert(ndev,
+ "Cannot set bittiming can is not in config mode\n");
+ return -EPERM;
+ }
+
+ netdev_dbg(ndev, "brp=%d,prop=%d,phase_seg1:%d,phase_reg2=%d,sjw=%d\n",
+ bt->brp, bt->prop_seg, bt->phase_seg1, bt->phase_seg2,
+ bt->sjw);
+
+ /* Setting Baud Rate prescalar value in BRPR Register */
+ btr0 = (bt->brp - 1) & XCAN_BRPR_BRP_MASK;
+
+ /* Setting Time Segment 1 in BTR Register */
+ btr1 = (bt->prop_seg + bt->phase_seg1 - 1) & XCAN_BTR_TS1_MASK;
+
+ /* Setting Time Segment 2 in BTR Register */
+ btr1 |= ((bt->phase_seg2 - 1) << XCAN_BTR_TS2_SHIFT) &
+ XCAN_BTR_TS2_MASK;
+
+ /* Setting Synchronous jump width in BTR Register */
+ btr1 |= ((bt->sjw - 1) << XCAN_BTR_SJW_SHIFT) & XCAN_BTR_SJW_MASK;
+
+ if (priv->can.ctrlmode & CAN_CTRLMODE_3_SAMPLES)
+ netdev_info(ndev, "Doesn't support Triple Sampling\n");
+ netdev_dbg(ndev, "Setting BTR0=0x%02x BTR1=0x%02x\n", btr0, btr1);
+
+ priv->write_reg(priv, XCAN_BRPR_OFFSET, btr0);
+ priv->write_reg(priv, XCAN_BTR_OFFSET, btr1);
+
+ netdev_dbg(ndev, "BRPR=0x%08x, BTR=0x%08x\n",
+ priv->read_reg(priv, XCAN_BRPR_OFFSET),
+ priv->read_reg(priv, XCAN_BTR_OFFSET));
+
+ return 0;
+}
+
+/**
+ * xcan_start - This the drivers start routine
+ * @ndev: Pointer to net_device structure
+ *
+ * This is the drivers start routine.
+ * Based on the State of the CAN device it puts
+ * the CAN device into a proper mode.
+ *
+ * Return: 0 always
+ */
+static int xcan_start(struct net_device *ndev)
+{
+ struct xcan_priv *priv = netdev_priv(ndev);
+
+ /* Check if it is in reset mode */
+ if (priv->can.state != CAN_STATE_STOPPED)
+ set_reset_mode(ndev);
+
+ /* Enable interrupts */
+ priv->write_reg(priv, XCAN_IER_OFFSET, XCAN_INTR_ALL);
+
+ /* Check whether it is loopback mode or normal mode */
+ if (priv->can.ctrlmode & CAN_CTRLMODE_LOOPBACK)
+ /* Put device into loopback mode */
+ priv->write_reg(priv, XCAN_MSR_OFFSET, XCAN_MSR_LBACK_MASK);
+ else
+ /* The device is in normal mode */
+ priv->write_reg(priv, XCAN_MSR_OFFSET, 0);
+
+ if (priv->can.state == CAN_STATE_STOPPED) {
+ /* Enable Xilinx CAN */
+ priv->write_reg(priv, XCAN_SRR_OFFSET, XCAN_SRR_CEN_MASK);
+ priv->can.state = CAN_STATE_ERROR_ACTIVE;
+ if (priv->can.ctrlmode & CAN_CTRLMODE_LOOPBACK) {
+ while ((priv->read_reg(priv, XCAN_SR_OFFSET) &
+ XCAN_SR_LBACK_MASK) == 0)
+ ;
+ } else {
+ while ((priv->read_reg(priv, XCAN_SR_OFFSET)
+ & XCAN_SR_NORMAL_MASK) == 0)
+ ;
+ }
+ netdev_dbg(ndev, "status:#x%08x\n",
+ priv->read_reg(priv, XCAN_SR_OFFSET));
+ }
+ priv->can.state = CAN_STATE_ERROR_ACTIVE;
+ return 0;
+}
+
+/**
+ * xcan_do_set_mode - This sets the mode of the driver
+ * @ndev: Pointer to net_device structure
+ * @mode: Tells the mode of the driver
+ *
+ * This check the drivers state and calls the
+ * the corresponding modes to set.
+ *
+ * Return: 0 on success and failure value on error
+ */
+static int xcan_do_set_mode(struct net_device *ndev, enum can_mode mode)
+{
+ struct xcan_priv *priv = netdev_priv(ndev);
+ int ret;
+
+ netdev_dbg(ndev, "Setting the mode of the driver%s\n", __func__);
+
+ if (!priv->open_time)
+ return -EINVAL;
+
+ switch (mode) {
+ case CAN_MODE_START:
+ ret = xcan_start(ndev);
+ if (ret < 0)
+ netdev_err(ndev, "xcan_start failed!\n");
+
+ if (netif_queue_stopped(ndev))
+ netif_wake_queue(ndev);
+ break;
+ default:
+ ret = -EOPNOTSUPP;
+ break;
+ }
+
+ return ret;
+}
+
+/**
+ * xcan_start_xmit - Starts the transmission
+ * @skb: sk_buff pointer that contains data to be Txed
+ * @ndev: Pointer to net_device structure
+ *
+ * This function is invoked from upper layers to initiate transmission. This
+ * function uses the next available free txbuff and populates their fields to
+ * start the transmission.
+ *
+ * Return: 0 on success and failure value on error
+ */
+static int xcan_start_xmit(struct sk_buff *skb, struct net_device *ndev)
+{
+ struct xcan_priv *priv = netdev_priv(ndev);
+ struct net_device_stats *stats = &ndev->stats;
+ struct can_frame *cf = (struct can_frame *)skb->data;
+ u32 id, dlc, tmp_dw1, tmp_dw2 = 0, data1, data2 = 0;
+ unsigned long flags;
+
+ /* Check if the TX buffer is full */
+ if (priv->read_reg(priv, XCAN_SR_OFFSET) & XCAN_SR_TXFLL_MASK) {
+ netif_stop_queue(ndev);
+ netdev_err(ndev, "TX register is still full!\n");
+ return NETDEV_TX_BUSY;
+ } else if (priv->waiting_ech_skb_num == priv->xcan_echo_skb_max_tx) {
+ netif_stop_queue(ndev);
+ netdev_err(ndev, "waiting:0x%08x, max:0x%08x\n",
+ priv->waiting_ech_skb_num, priv->xcan_echo_skb_max_tx);
+ return NETDEV_TX_BUSY;
+ }
+ /* Watch carefully on the bit sequence */
+ if ((cf->can_id & CAN_EFF_FLAG) == 0) {
+ /* Standard CAN ID format */
+ id = ((cf->can_id & CAN_SFF_MASK) << XCAN_IDR_ID1_SHIFT) &
+ XCAN_IDR_ID1_MASK;
+
+ if (cf->can_id & CAN_RTR_FLAG)
+ /* Extended frames remote TX request */
+ id |= XCAN_IDR_SRR_MASK;
+ } else {
+ /* Extended CAN ID format */
+ id = ((cf->can_id & CAN_EFF_MASK) << XCAN_IDR_ID2_SHIFT) &
+ XCAN_IDR_ID2_MASK;
+ id |= (((cf->can_id & CAN_EFF_MASK) >>
+ (CAN_EFF_ID_BITS-CAN_SFF_ID_BITS)) <<
+ XCAN_IDR_ID1_SHIFT) & XCAN_IDR_ID1_MASK;
+
+ /* The substibute remote TX request bit should be "1"
+ * for extended frames as in the Xilinx CAN datasheet
+ */
+ id |= XCAN_IDR_IDE_MASK | XCAN_IDR_SRR_MASK;
+
+ if (cf->can_id & CAN_RTR_FLAG)
+ /* Extended frames remote TX request */
+ id |= XCAN_IDR_RTR_MASK;
+ }
+
+ dlc = (cf->can_dlc & 0xf) << XCAN_DLCR_DLC_SHIFT;
+
+ tmp_dw1 = le32_to_cpup((u32 *)(cf->data));
+ data1 = htonl(tmp_dw1);
+ if (dlc > 4) {
+ tmp_dw2 = le32_to_cpup((u32 *)(cf->data + 4));
+ data2 = htonl(tmp_dw2);
+ }
+
+ netdev_dbg(ndev, "tx:id=0x%08x,dlc=0x%08x,d1=0x%08x,d2=0x%08x\n",
+ id, dlc, data1, data2);
+
+ /* Write the Frame to Xilinx CAN TX FIFO */
+ priv->write_reg(priv, XCAN_TXFIFO_ID_OFFSET, id);
+ priv->write_reg(priv, XCAN_TXFIFO_DLC_OFFSET, dlc);
+ priv->write_reg(priv, XCAN_TXFIFO_DW1_OFFSET, data1);
+ priv->write_reg(priv, XCAN_TXFIFO_DW2_OFFSET, data2);
+ stats->tx_bytes += cf->can_dlc;
+ ndev->trans_start = jiffies;
+
+ can_put_echo_skb(skb, ndev, priv->ech_skb_next);
+
+ priv->ech_skb_next = (priv->ech_skb_next + 1) %
+ priv->xcan_echo_skb_max_tx;
+
+ spin_lock_irqsave(&priv->ech_skb_lock, flags);
+ priv->waiting_ech_skb_num++;
+ spin_unlock_irqrestore(&priv->ech_skb_lock, flags);
+
+ return NETDEV_TX_OK;
+}
+
+/**
+ * xcan_rx - Is called from CAN isr to complete the received
+ * frame processing
+ * @ndev: Pointer to net_device structure
+ *
+ * This function is invoked from the CAN isr(poll) to process the Rx frames. It
+ * does minimal processing and invokes "netif_receive_skb" to complete further
+ * processing.
+ * Return: 0 on success and negative error value on error
+ */
+static int xcan_rx(struct net_device *ndev)
+{
+ struct xcan_priv *priv = netdev_priv(ndev);
+ struct net_device_stats *stats = &ndev->stats;
+ struct can_frame *cf;
+ struct sk_buff *skb;
+ u32 id_xcan, dlc, data1, data2;
+
+ skb = alloc_can_skb(ndev, &cf);
+ if (!skb)
+ return -ENOMEM;
+
+ /* Read a frame from Xilinx zynq CANPS */
+ id_xcan = priv->read_reg(priv, XCAN_RXFIFO_ID_OFFSET);
+ dlc = priv->read_reg(priv, XCAN_RXFIFO_DLC_OFFSET) & XCAN_DLCR_DLC_MASK;
+ data1 = priv->read_reg(priv, XCAN_RXFIFO_DW1_OFFSET);
+ data2 = priv->read_reg(priv, XCAN_RXFIFO_DW2_OFFSET);
+ netdev_dbg(ndev, "rx:id=0x%08x,dlc=0x%08x,d1=0x%08x,d2=0x%08x\n",
+ id_xcan, dlc, data1, data2);
+
+ /* Change Xilinx CAN data length format to socketCAN data format */
+ cf->can_dlc = get_can_dlc((dlc & XCAN_DLCR_DLC_MASK) >>
+ XCAN_DLCR_DLC_SHIFT);
+
+ /* Change Xilinx CAN ID format to socketCAN ID format */
+ if (id_xcan & XCAN_IDR_IDE_MASK) {
+ /* The received frame is an Extended format frame */
+ cf->can_id = (id_xcan & XCAN_IDR_ID1_MASK) >> 3;
+ cf->can_id |= (id_xcan & XCAN_IDR_ID2_MASK) >>
+ XCAN_IDR_ID2_SHIFT;
+ cf->can_id |= CAN_EFF_FLAG;
+ if (id_xcan & XCAN_IDR_RTR_MASK)
+ cf->can_id |= CAN_RTR_FLAG;
+ } else {
+ /* The received frame is a standard format frame */
+ cf->can_id = (id_xcan & XCAN_IDR_ID1_MASK) >>
+ XCAN_IDR_ID1_SHIFT;
+ if (id_xcan & XCAN_IDR_RTR_MASK)
+ cf->can_id |= CAN_RTR_FLAG;
+ }
+
+ /* Change Xilinx CAN data format to socketCAN data format */
+ *(u32 *)(cf->data) = ntohl(data1);
+ if (cf->can_dlc > 4)
+ *(u32 *)(cf->data + 4) = ntohl(data2);
+ else
+ *(u32 *)(cf->data + 4) = 0;
+ stats->rx_bytes += cf->can_dlc;
+
+ can_led_event(ndev, CAN_LED_EVENT_RX);
+
+ netif_receive_skb(skb);
+
+ stats->rx_packets++;
+ return 0;
+}
+
+/**
+ * xcan_err_interrupt - error frame Isr
+ * @ndev: net_device pointer
+ * @isr: interrupt status register value
+ *
+ * This is the CAN error interrupt and it will
+ * check the the type of error and forward the error
+ * frame to upper layers.
+ */
+static void xcan_err_interrupt(struct net_device *ndev, u32 isr)
+{
+ struct xcan_priv *priv = netdev_priv(ndev);
+ struct net_device_stats *stats = &ndev->stats;
+ struct can_frame *cf;
+ struct sk_buff *skb;
+ u32 err_status, status;
+
+ skb = alloc_can_err_skb(ndev, &cf);
+ if (!skb) {
+ netdev_err(ndev, "alloc_can_err_skb() failed!\n");
+ return;
+ }
+
+ err_status = priv->read_reg(priv, XCAN_ESR_OFFSET);
+ priv->write_reg(priv, XCAN_ESR_OFFSET, err_status);
+ status = priv->read_reg(priv, XCAN_SR_OFFSET);
+
+ if (isr & XCAN_IXR_BSOFF_MASK) {
+ priv->can.state = CAN_STATE_BUS_OFF;
+ cf->can_id |= CAN_ERR_BUSOFF;
+ priv->can.can_stats.bus_off++;
+ /* Leave device in Config Mode in bus-off state */
+ priv->write_reg(priv, XCAN_SRR_OFFSET, XCAN_SRR_RESET_MASK);
+ can_bus_off(ndev);
+ } else if ((status & XCAN_SR_ESTAT_MASK) == XCAN_SR_ESTAT_MASK) {
+ cf->can_id |= CAN_ERR_CRTL;
+ priv->can.state = CAN_STATE_ERROR_PASSIVE;
+ priv->can.can_stats.error_passive++;
+ cf->data[1] |= CAN_ERR_CRTL_RX_PASSIVE |
+ CAN_ERR_CRTL_TX_PASSIVE;
+ } else if (status & XCAN_SR_ERRWRN_MASK) {
+ cf->can_id |= CAN_ERR_CRTL;
+ priv->can.state = CAN_STATE_ERROR_WARNING;
+ priv->can.can_stats.error_warning++;
+ cf->data[1] |= CAN_ERR_CRTL_RX_WARNING |
+ CAN_ERR_CRTL_TX_WARNING;
+ }
+
+ /* Check for Arbitration lost interrupt */
+ if (isr & XCAN_IXR_ARBLST_MASK) {
+ cf->can_id |= CAN_ERR_LOSTARB;
+ cf->data[0] = CAN_ERR_LOSTARB_UNSPEC;
+ priv->can.can_stats.arbitration_lost++;
+ }
+
+ /* Check for RX FIFO Overflow interrupt */
+ if (isr & XCAN_IXR_RXOFLW_MASK) {
+ cf->can_id |= CAN_ERR_CRTL;
+ cf->data[1] |= CAN_ERR_CRTL_RX_OVERFLOW;
+ stats->rx_over_errors++;
+ stats->rx_errors++;
+ priv->write_reg(priv, XCAN_SRR_OFFSET, XCAN_SRR_RESET_MASK);
+ }
+
+ /* Check for error interrupt */
+ if (isr & XCAN_IXR_ERROR_MASK) {
+ cf->can_id |= CAN_ERR_PROT | CAN_ERR_BUSERROR;
+ cf->data[2] |= CAN_ERR_PROT_UNSPEC;
+
+ /* Check for Ack error interrupt */
+ if (err_status & XCAN_ESR_ACKER_MASK) {
+ cf->can_id |= CAN_ERR_ACK;
+ cf->data[3] |= CAN_ERR_PROT_LOC_ACK;
+ stats->tx_errors++;
+ }
+
+ /* Check for Bit error interrupt */
+ if (err_status & XCAN_ESR_BERR_MASK) {
+ cf->can_id |= CAN_ERR_PROT;
+ cf->data[2] = CAN_ERR_PROT_BIT;
+ stats->tx_errors++;
+ }
+
+ /* Check for Stuff error interrupt */
+ if (err_status & XCAN_ESR_STER_MASK) {
+ cf->can_id |= CAN_ERR_PROT;
+ cf->data[2] = CAN_ERR_PROT_STUFF;
+ stats->rx_errors++;
+ }
+
+ /* Check for Form error interrupt */
+ if (err_status & XCAN_ESR_FMER_MASK) {
+ cf->can_id |= CAN_ERR_PROT;
+ cf->data[2] = CAN_ERR_PROT_FORM;
+ stats->rx_errors++;
+ }
+
+ /* Check for CRC error interrupt */
+ if (err_status & XCAN_ESR_CRCER_MASK) {
+ cf->can_id |= CAN_ERR_PROT;
+ cf->data[3] = CAN_ERR_PROT_LOC_CRC_SEQ |
+ CAN_ERR_PROT_LOC_CRC_DEL;
+ stats->rx_errors++;
+ }
+ priv->can.can_stats.bus_error++;
+ }
+
+ netif_rx(skb);
+ stats->rx_packets++;
+ stats->rx_bytes += cf->can_dlc;
+
+ netdev_dbg(ndev, "%s: error status register:0x%x\n",
+ __func__, priv->read_reg(priv, XCAN_ESR_OFFSET));
+}
+
+/**
+ * xcan_state_interrupt - It will check the state of the CAN device
+ * @ndev: net_device pointer
+ * @isr: interrupt status register value
+ *
+ * This will checks the state of the CAN device
+ * and puts the device into appropriate state.
+ */
+static void xcan_state_interrupt(struct net_device *ndev, u32 isr)
+{
+ struct xcan_priv *priv = netdev_priv(ndev);
+
+ /* Check for Sleep interrupt if set put CAN device in sleep state */
+ if (isr & XCAN_IXR_SLP_MASK)
+ priv->can.state = CAN_STATE_SLEEPING;
+
+ /* Check for Wake up interrupt if set put CAN device in Active state */
+ if (isr & XCAN_IXR_WKUP_MASK)
+ priv->can.state = CAN_STATE_ERROR_ACTIVE;
+}
+
+/**
+ * xcan_rx_poll - Poll routine for rx packets (NAPI)
+ * @napi: napi structure pointer
+ * @quota: Max number of rx packets to be processed.
+ *
+ * This is the poll routine for rx part.
+ * It will process the packets maximux quota value.
+ *
+ * Return: number of packets received
+ */
+static int xcan_rx_poll(struct napi_struct *napi, int quota)
+{
+ struct net_device *ndev = napi->dev;
+ struct xcan_priv *priv = netdev_priv(ndev);
+ u32 isr, ier;
+ int work_done = 0;
+
+ isr = priv->read_reg(priv, XCAN_ISR_OFFSET);
+ while ((isr & XCAN_IXR_RXNEMP_MASK) && (work_done < quota)) {
+ if (isr & XCAN_IXR_RXOK_MASK) {
+ priv->write_reg(priv, XCAN_ICR_OFFSET,
+ XCAN_IXR_RXOK_MASK);
+ if (xcan_rx(ndev) < 0)
+ return work_done;
+ work_done++;
+ } else {
+ priv->write_reg(priv, XCAN_ICR_OFFSET,
+ XCAN_IXR_RXNEMP_MASK);
+ break;
+ }
+ priv->write_reg(priv, XCAN_ICR_OFFSET, XCAN_IXR_RXNEMP_MASK);
+ isr = priv->read_reg(priv, XCAN_ISR_OFFSET);
+ }
+
+ if (work_done < quota) {
+ napi_complete(napi);
+ ier = priv->read_reg(priv, XCAN_IER_OFFSET);
+ ier |= (XCAN_IXR_RXOK_MASK | XCAN_IXR_RXNEMP_MASK);
+ priv->write_reg(priv, XCAN_IER_OFFSET, ier);
+ }
+ return work_done;
+}
+
+/**
+ * xcan_tx_interrupt - Tx Done Isr
+ * @ndev: net_device pointer
+ */
+static void xcan_tx_interrupt(struct net_device *ndev)
+{
+ unsigned long flags;
+ struct xcan_priv *priv = netdev_priv(ndev);
+ struct net_device_stats *stats = &ndev->stats;
+ u32 processed = 0, txpackets;
+
+ stats->tx_packets++;
+ netdev_dbg(ndev, "%s: waiting total:%d,current:%d\n", __func__,
+ priv->waiting_ech_skb_num, priv->waiting_ech_skb_index);
+
+ txpackets = priv->waiting_ech_skb_num;
+
+ if (txpackets) {
+ can_get_echo_skb(ndev, priv->waiting_ech_skb_index);
+ priv->waiting_ech_skb_index =
+ (priv->waiting_ech_skb_index + 1) %
+ priv->xcan_echo_skb_max_tx;
+ processed++;
+ txpackets--;
+ }
+
+ spin_lock_irqsave(&priv->ech_skb_lock, flags);
+ priv->waiting_ech_skb_num -= processed;
+ spin_unlock_irqrestore(&priv->ech_skb_lock, flags);
+
+ netdev_dbg(ndev, "%s: waiting total:%d,current:%d\n", __func__,
+ priv->waiting_ech_skb_num, priv->waiting_ech_skb_index);
+
+ netif_wake_queue(ndev);
+
+ can_led_event(ndev, CAN_LED_EVENT_TX);
+}
+
+/**
+ * xcan_interrupt - CAN Isr
+ * @irq: irq number
+ * @dev_id: device id poniter
+ *
+ * This is the xilinx CAN Isr. It checks for the type of interrupt
+ * and invokes the corresponding ISR.
+ *
+ * Return:
+ * IRQ_NONE - If CAN device is in sleep mode, IRQ_HANDLED otherwise
+ */
+static irqreturn_t xcan_interrupt(int irq, void *dev_id)
+{
+ struct net_device *ndev = (struct net_device *)dev_id;
+ struct xcan_priv *priv = netdev_priv(ndev);
+ u32 isr, ier;
+
+ if (priv->can.state == CAN_STATE_STOPPED)
+ return IRQ_NONE;
+
+ /* Get the interrupt status from Xilinx CAN */
+ isr = priv->read_reg(priv, XCAN_ISR_OFFSET);
+ if (!isr)
+ return IRQ_NONE;
+
+ netdev_dbg(ndev, "%s: isr:#x%08x, err:#x%08x\n", __func__,
+ isr, priv->read_reg(priv, XCAN_ESR_OFFSET));
+
+ /* Check for the type of interrupt and Processing it */
+ if (isr & (XCAN_IXR_SLP_MASK | XCAN_IXR_WKUP_MASK)) {
+ priv->write_reg(priv, XCAN_ICR_OFFSET, (XCAN_IXR_SLP_MASK |
+ XCAN_IXR_WKUP_MASK));
+ xcan_state_interrupt(ndev, isr);
+ }
+
+ /* Check for Tx interrupt and Processing it */
+ if (isr & XCAN_IXR_TXOK_MASK) {
+ priv->write_reg(priv, XCAN_ICR_OFFSET, XCAN_IXR_TXOK_MASK);
+ xcan_tx_interrupt(ndev);
+ }
+
+ /* Check for the type of error interrupt and Processing it */
+ if (isr & (XCAN_IXR_ERROR_MASK | XCAN_IXR_RXOFLW_MASK |
+ XCAN_IXR_BSOFF_MASK | XCAN_IXR_ARBLST_MASK)) {
+ priv->write_reg(priv, XCAN_ICR_OFFSET, (XCAN_IXR_ERROR_MASK |
+ XCAN_IXR_RXOFLW_MASK | XCAN_IXR_BSOFF_MASK |
+ XCAN_IXR_ARBLST_MASK));
+ xcan_err_interrupt(ndev, isr);
+ }
+
+ /* Check for the type of receive interrupt and Processing it */
+ if (isr & (XCAN_IXR_RXNEMP_MASK | XCAN_IXR_RXOK_MASK)) {
+ ier = priv->read_reg(priv, XCAN_IER_OFFSET);
+ ier &= ~(XCAN_IXR_RXNEMP_MASK | XCAN_IXR_RXOK_MASK);
+ priv->write_reg(priv, XCAN_IER_OFFSET, ier);
+ napi_schedule(&priv->napi);
+ }
+ return IRQ_HANDLED;
+}
+
+/**
+ * xcan_stop - Driver stop routine
+ * @ndev: Pointer to net_device structure
+ *
+ * This is the drivers stop routine. It will disable the
+ * interrupts and put the device into configuration mode.
+ */
+static void xcan_stop(struct net_device *ndev)
+{
+ struct xcan_priv *priv = netdev_priv(ndev);
+ u32 ier;
+
+ /* Disable interrupts and leave the can in configuration mode */
+ ier = priv->read_reg(priv, XCAN_IER_OFFSET);
+ ier &= ~XCAN_INTR_ALL;
+ priv->write_reg(priv, XCAN_IER_OFFSET, ier);
+ priv->write_reg(priv, XCAN_SRR_OFFSET, XCAN_SRR_RESET_MASK);
+ priv->can.state = CAN_STATE_STOPPED;
+}
+
+/**
+ * xcan_open - Driver open routine
+ * @ndev: Pointer to net_device structure
+ *
+ * This is the driver open routine.
+ * Return: 0 on success and failure value on error
+ */
+static int xcan_open(struct net_device *ndev)
+{
+ struct xcan_priv *priv = netdev_priv(ndev);
+ int err;
+
+ /* Set chip into reset mode */
+ err = set_reset_mode(ndev);
+ if (err < 0)
+ netdev_err(ndev, "mode resetting failed failed!\n");
+
+ /* Common open */
+ err = open_candev(ndev);
+ if (err)
+ return err;
+
+ err = xcan_start(ndev);
+ if (err < 0)
+ netdev_err(ndev, "xcan_start failed!\n");
+
+
+ can_led_event(ndev, CAN_LED_EVENT_OPEN);
+ napi_enable(&priv->napi);
+ netif_start_queue(ndev);
+
+ return 0;
+}
+
+/**
+ * xcan_close - Driver close routine
+ * @ndev: Pointer to net_device structure
+ *
+ * Return: 0 always
+ */
+static int xcan_close(struct net_device *ndev)
+{
+ struct xcan_priv *priv = netdev_priv(ndev);
+
+ netif_stop_queue(ndev);
+ napi_disable(&priv->napi);
+ xcan_stop(ndev);
+ close_candev(ndev);
+
+ can_led_event(ndev, CAN_LED_EVENT_STOP);
+
+ return 0;
+}
+
+/**
+ * xcan_get_berr_counter - error counter routine
+ * @ndev: Pointer to net_device structure
+ * @bec: Pointer to can_berr_counter structure
+ *
+ * This is the driver error counter routine.
+ * Return: 0 always
+ */
+static int xcan_get_berr_counter(const struct net_device *ndev,
+ struct can_berr_counter *bec)
+{
+ struct xcan_priv *priv = netdev_priv(ndev);
+
+ bec->txerr = priv->read_reg(priv, XCAN_ECR_OFFSET) & XCAN_ECR_TEC_MASK;
+ bec->rxerr = ((priv->read_reg(priv, XCAN_ECR_OFFSET) &
+ XCAN_ECR_REC_MASK) >> XCAN_ESR_REC_SHIFT);
+ return 0;
+}
+
+static const struct net_device_ops xcan_netdev_ops = {
+ .ndo_open = xcan_open,
+ .ndo_stop = xcan_close,
+ .ndo_start_xmit = xcan_start_xmit,
+};
+
+#ifdef CONFIG_PM_SLEEP
+/**
+ * xcan_suspend - Suspend method for the driver
+ * @_dev: Address of the platform_device structure
+ *
+ * Put the driver into low power mode.
+ * Return: 0 always
+ */
+static int xcan_suspend(struct device *_dev)
+{
+ struct platform_device *pdev = container_of(_dev,
+ struct platform_device, dev);
+ struct net_device *ndev = platform_get_drvdata(pdev);
+ struct xcan_priv *priv = netdev_priv(ndev);
+
+ if (netif_running(ndev)) {
+ netif_stop_queue(ndev);
+ netif_device_detach(ndev);
+ }
+
+ priv->write_reg(priv, XCAN_MSR_OFFSET, XCAN_MSR_SLEEP_MASK);
+ priv->can.state = CAN_STATE_SLEEPING;
+
+ clk_disable(priv->aperclk);
+ clk_disable(priv->devclk);
+
+ return 0;
+}
+
+/**
+ * xcan_resume - Resume from suspend
+ * @dev: Address of the platformdevice structure
+ *
+ * Resume operation after suspend.
+ * Return: 0 on success and failure value on error
+ */
+static int xcan_resume(struct device *dev)
+{
+ struct platform_device *pdev = container_of(dev,
+ struct platform_device, dev);
+ struct net_device *ndev = platform_get_drvdata(pdev);
+ struct xcan_priv *priv = netdev_priv(ndev);
+ int ret;
+
+ ret = clk_enable(priv->aperclk);
+ if (ret) {
+ dev_err(dev, "Cannot enable clock.\n");
+ return ret;
+ }
+ ret = clk_enable(priv->devclk);
+ if (ret) {
+ dev_err(dev, "Cannot enable clock.\n");
+ return ret;
+ }
+
+ priv->write_reg(priv, XCAN_MSR_OFFSET, 0);
+ priv->write_reg(priv, XCAN_SRR_OFFSET, XCAN_SRR_CEN_MASK);
+ priv->can.state = CAN_STATE_ERROR_ACTIVE;
+
+ if (netif_running(ndev)) {
+ netif_device_attach(ndev);
+ netif_start_queue(ndev);
+ }
+
+ return 0;
+}
+#endif
+
+static SIMPLE_DEV_PM_OPS(xcan_dev_pm_ops, xcan_suspend, xcan_resume);
+
+/**
+ * xcan_probe - Platform registration call
+ * @pdev: Handle to the platform device structure
+ *
+ * This function does all the memory allocation and registration for the CAN
+ * device.
+ *
+ * Return: 0 on success and failure value on error
+ */
+static int xcan_probe(struct platform_device *pdev)
+{
+ struct resource *res; /* IO mem resources */
+ struct net_device *ndev;
+ struct xcan_priv *priv;
+ int ret, fifodep;
+
+ /* Create a CAN device instance */
+ ndev = alloc_candev(sizeof(struct xcan_priv), XCAN_ECHO_SKB_MAX);
+ if (!ndev)
+ return -ENOMEM;
+
+ priv = netdev_priv(ndev);
+ priv->dev = ndev;
+ priv->can.bittiming_const = &xcan_bittiming_const;
+ priv->can.do_set_bittiming = xcan_set_bittiming;
+ priv->can.do_set_mode = xcan_do_set_mode;
+ priv->can.do_get_berr_counter = xcan_get_berr_counter;
+ priv->can.ctrlmode_supported = CAN_CTRLMODE_LOOPBACK |
+ CAN_CTRLMODE_BERR_REPORTING;
+ priv->xcan_echo_skb_max_tx = XCAN_ECHO_SKB_MAX;
+ priv->xcan_echo_skb_max_rx = XCAN_NAPI_WEIGHT;
+
+ /* Get IRQ for the device */
+ ndev->irq = platform_get_irq(pdev, 0);
+ ret = devm_request_irq(&pdev->dev, ndev->irq, &xcan_interrupt,
+ priv->irq_flags, dev_name(&pdev->dev),
+ (void *)ndev);
+ if (ret < 0) {
+ dev_err(&pdev->dev, "Irq allocation for CAN failed\n");
+ goto err_free;
+ }
+
+ spin_lock_init(&priv->ech_skb_lock);
+ ndev->flags |= IFF_ECHO; /* We support local echo */
+
+ platform_set_drvdata(pdev, ndev);
+ SET_NETDEV_DEV(ndev, &pdev->dev);
+ ndev->netdev_ops = &xcan_netdev_ops;
+
+ /* Get the virtual base address for the device */
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ priv->reg_base = devm_ioremap_resource(&pdev->dev, res);
+ if (IS_ERR(priv->reg_base)) {
+ ret = PTR_ERR(priv->reg_base);
+ goto err_free;
+ }
+ ndev->mem_start = res->start;
+ ndev->mem_end = res->end;
+
+ priv->write_reg = xcan_write_reg;
+ priv->read_reg = xcan_read_reg;
+
+ /* Getting the CAN devclk info */
+ priv->devclk = devm_clk_get(&pdev->dev, "ref_clk");
+ if (IS_ERR(priv->devclk)) {
+ dev_err(&pdev->dev, "Device clock not found.\n");
+ ret = PTR_ERR(priv->devclk);
+ goto err_free;
+ }
+
+ /* Check for type of CAN device */
+ if (of_device_is_compatible(pdev->dev.of_node,
+ "xlnx,zynq-can-1.00.a")) {
+ priv->aperclk = devm_clk_get(&pdev->dev, "aper_clk");
+ if (IS_ERR(priv->aperclk)) {
+ dev_err(&pdev->dev, "aper clock not found\n");
+ ret = PTR_ERR(priv->aperclk);
+ goto err_free;
+ }
+ } else {
+ priv->aperclk = priv->devclk;
+ ret = of_property_read_u32(pdev->dev.of_node,
+ "xlnx,can-tx-dpth", &fifodep);
+ if (ret < 0)
+ goto err_free;
+ priv->xcan_echo_skb_max_tx = fifodep;
+ ret = of_property_read_u32(pdev->dev.of_node,
+ "xlnx,can-rx-dpth", &fifodep);
+ if (ret < 0)
+ goto err_free;
+ priv->xcan_echo_skb_max_rx = fifodep;
+ }
+
+ ret = clk_prepare_enable(priv->devclk);
+ if (ret) {
+ dev_err(&pdev->dev, "unable to enable device clock\n");
+ goto err_free;
+ }
+
+ ret = clk_prepare_enable(priv->aperclk);
+ if (ret) {
+ dev_err(&pdev->dev, "unable to enable aper clock\n");
+ goto err_unprepar_disabledev;
+ }
+
+ priv->can.clock.freq = clk_get_rate(priv->devclk);
+
+ netif_napi_add(ndev, &priv->napi, xcan_rx_poll,
+ priv->xcan_echo_skb_max_rx);
+ ret = register_candev(ndev);
+ if (ret) {
+ dev_err(&pdev->dev, "fail to register failed (err=%d)\n", ret);
+ goto err_unprepar_disableaper;
+ }
+
+ devm_can_led_init(ndev);
+ dev_info(&pdev->dev,
+ "reg_base=0x%p irq=%d clock=%d, tx fifo depth:%d\n",
+ priv->reg_base, ndev->irq, priv->can.clock.freq,
+ priv->xcan_echo_skb_max_tx);
+
+ return 0;
+
+err_unprepar_disableaper:
+ clk_disable_unprepare(priv->aperclk);
+err_unprepar_disabledev:
+ clk_disable_unprepare(priv->devclk);
+err_free:
+ free_candev(ndev);
+
+ return ret;
+}
+
+/**
+ * xcan_remove - Unregister the device after releasing the resources
+ * @pdev: Handle to the platform device structure
+ *
+ * This function frees all the resources allocated to the device.
+ * Return: 0 always
+ */
+static int xcan_remove(struct platform_device *pdev)
+{
+ struct net_device *ndev = platform_get_drvdata(pdev);
+ struct xcan_priv *priv = netdev_priv(ndev);
+
+ if (set_reset_mode(ndev) < 0)
+ netdev_err(ndev, "mode resetting failed!\n");
+
+ unregister_candev(ndev);
+ netif_napi_del(&priv->napi);
+ clk_disable_unprepare(priv->aperclk);
+ clk_disable_unprepare(priv->devclk);
+
+ free_candev(ndev);
+
+ return 0;
+}
+
+/* Match table for OF platform binding */
+static struct of_device_id xcan_of_match[] = {
+ { .compatible = "xlnx,zynq-can-1.00.a", },
+ { .compatible = "xlnx,axi-can-1.00.a", },
+ { /* end of list */ },
+};
+MODULE_DEVICE_TABLE(of, xcan_of_match);
+
+static struct platform_driver xcan_driver = {
+ .probe = xcan_probe,
+ .remove = xcan_remove,
+ .driver = {
+ .owner = THIS_MODULE,
+ .name = DRIVER_NAME,
+ .pm = &xcan_dev_pm_ops,
+ .of_match_table = xcan_of_match,
+ },
+};
+
+module_platform_driver(xcan_driver);
+
+MODULE_LICENSE("GPL");
+MODULE_AUTHOR("Xilinx Inc");
+MODULE_DESCRIPTION("Xilinx CAN interface");
--
1.7.4
More information about the linux-arm-kernel
mailing list